JMODEM executes best from a batch file as an external pro-
tocol for any of the communications programs that have ex-
ternal-protocol capability. A typical communications program
is TELIX.
DESCRIPTION
The DCP0105 family is a series of high efficiency, 5V
input isolated DC/DC converters. In addition to 1W
nominal galvanically isolated output power capability,
the range of DC/DCs are also fully synchronizable.
The devices feature thermal shutdown, and overload
protection is implemented via watchdog circuitry.
Advanced power-on reset techniques give superior
reset performance and the devices will start into any
capacitive load up to full power output.
The DCP0105 family is implemented in standard-
molded IC packaging, giving outlines suitable for high
volume assembly.
This application note describes the three methods that can be used to
program the Flash code memory of the 89C51Rx+/Rx2/66x families
of microcontrollers. It discusses in detail the operation of the
In-System Programming (ISP) capability which allows these
microcontrollers to be programmed while mounted in the end product.
These microcontrollers also have an In-Application Programming
(IAP) capability which allows them to be programmed under firmware
control of the embedded application. This capability is also described
The W78E58B is an 8-bit microcontroller which has an in-system programmable Flash EPROM for
firmware updating. The instruction set of the W78E58B is fully compatible with the standard 8052. The
W78E58B contains a 32K bytes of main ROM and a 4K bytes of auxiliary ROM which allows the
contents of the 32KB main ROM to be updated by the loader program located at the 4KB auxiliary
ROM 512 bytes of on-chip RAM four 8-bit bi-directional and bit-addressable I/O ports an additional 4-
bit port P4 three 16-bit timer/counters a serial port. These peripherals are supported by a eight
sources two-level interrupt capability. To facilitate programming and verification, the ROM inside the
W78E58B allows the program memory to be programmed and read electronically. Once the code is
confirmed, the user can protect the code for security
I always believe that one will easily lag behind unless he keeps on learning. Of course, if I am given a chance for advanced studies in this famous University , I will stare to effort to master a good command of advance my capability.
Introduction
? ?
The ARM Cortex -A8 microprocessor is the first applications microprocessor in ARM!ˉs
new Cortex family. With high performance and power efficiency, it targets a wide
variety of mobile and consumer applications including mobile phones, set-top boxes,
gaming consoles and automotive navigation/entertainment systems. The Cortex-A8
processor spans a range of performance points depending on the implementation,
delivering over to 2000 Dhrystone MIPS (DMIPS) of performance for demanding
consumer applications and consuming less than 300mW for low-power mobile devices.
This translates into a large increase in processing capability while staying with the
power levels of previous generations of mobile devices. Consumer applications will
benefit from the reduced heat dissipation and resulting lower packaging and integration
costs.
An Overview of Smart Card Security.
The smart card, an intelligent token, is a credit card sized plastic card embedded with an integrated circuit chip. It provides not only memory capacity, but computational capability as well. The self-containment of smart card makes it resistant to attack as it does not need to depend upon potentially vulnerable external resources. Because of this characteristic, smart cards are often used in different applications which require strong security protection and authentication.
Among the many features built into Microchip’sEnhanced FLASH Microcontroller devices is the capability of the program memory to self-program. This very useful feature has been deliberately included to give the user the ability to perform bootloading operations.Devices like the PIC18F452 are designed with a designated“boot block”, a small section of protectable program memory allocated specifically for bootload firmware.
Among the many features built into Microchip’sEnhanced FLASH Microcontroller devices is the capability of the program memory to self-program. This very useful feature has been deliberately included to give the user the ability to perform bootloading operations.Devices like the PIC18F452 are designed with a designated“boot block”, a small section of protectable program memory allocated specifically for bootload firmware.
