circular convolution using 6713 tms320 kit
標簽： convolution circular using 6713
上傳時間： 2013-12-24
上傳用戶：天誠24
circular convolution code in matlab
標簽： convolution circular matlab code
上傳時間： 2017-07-01
上傳用戶：pompey
circular Buffer / Queue immplementation
標簽： immplementation circular Buffer Queue
上傳時間： 2013-12-24
上傳用戶：huannan88
source code c54x FIR filter with circular addressing
標簽： addressing circular source filter
上傳時間： 2017-08-17
上傳用戶：hebmuljb
基于幅移鍵控技術ASK（Amplitude-Shift Keying），以C8051F340單片機作為監測終端控制器，C8051F330D單片機作為探測節點控制器，采用半雙工的通信方式，通過監控終端和探測節點的無線收發電路，實現數據的雙向無線傳輸。收發電路采用直徑為0.8 mm的漆包線自行繞制成圓形空心線圈天線，天線直徑為（3.4±0.3）cm。試驗表明，探測節點與監測終端的通信距離為24 cm，通過橋接方式，節點收發功率為102 mW時，節點間的通信距離可達20 cm。與傳統無線收發模塊相比，該無線收發電路在受體積、功耗、成本限制的場合有廣闊的應用前景。 Abstract: Based on ASK technology and with the C8051F340 and C8051F330D MCU as the controller， using half-duplex communication mode， this paper achieves bi-directional data transfer. Transceiver circuit constituted by enameled wire which diameter is 0.8mm and wound into a diameter （3.4±0.3） cm circular hollow coil antenna. Tests show that the communication distance between detection and monitoring of the terminal is 24cm，the distance is up to 20cm between two nodes when using the manner of bridging and the node transceiver power is 102mW. Compared with the conventional wireless transceiver modules， the circuit has wide application prospect in small size， low cost and low power consumption and other characteristics.
上傳時間： 2013-10-19
上傳用戶：xz85592677
The view238 application is a simple tool for graphically displaying STEP-NC toolpaths. It is a Java application that reads AP-238 XML data using the DOM inferface, then finds and display the toolpaths within. At present, only polylines, and circular arcs are processed.
標簽： application graphically displaying toolpaths
上傳時間： 2013-12-02
上傳用戶：zhangliming420
These Simulink blocks contain transfer functions that model the pressure and flow transients for axisymmetric 2D viscous flow of a compressible fluid in a straight rigid circular cross section pipelines. Three models are available: (1) pressures at the ends (2) flow rates at the ends (3) pressure at one end and flow rate at the other Filtering is incorporated to reduce numerical oscillation (Gibbs phenomenon). See J. Dyn. Systems, Meas. & Control vol 122 (2000) pp. 153-162.
標簽： transients functions Simulink transfer
上傳時間： 2014-01-22
上傳用戶：Shaikh
This example describes how to use the ADC and DMA to transfer continuously converted data from ADC to a data buffer. The ADC is configured to converts continuously ADC channel14. Each time an end of conversion occurs the DMA transfers, in circular mode, the converted data from ADC1 DR register to the ADC_ConvertedValue variable. The ADC1 clock is set to 14 MHz.
標簽： continuously ADC describes converted
上傳時間： 2014-01-03
上傳用戶：徐孺
usb bulk 傳輸例程。 * The bulkusb driver is a generic function driver, based on the Windows Driver Model (WDM). * Supports Plug and Play(PnP), Power Management(PM), Windows Management Instrumentation (WMI) and the Selective Suspend (SS) features. * This sample is based off the selSusp DDK sample. Please refer the selSusp sample and the DDK docs to understand the handling of PnP, PM, WMI and SS features and implementations. * The USB device used for this sample is a generic Intel I82930 USB evaluation board programmed with a simple loopback test using a 64 KB circular buffer. None of the code in the sample is specific to this controller chip.
標簽： driver function Windows bulkusb
上傳時間： 2016-04-25
上傳用戶：270189020
cordic methods describe essentially the same algorithm that with suitably chosen inputs can be used to calculate a whole range of scientific functions including sin, cos, tan, arctan, arcsin, arccos, sinh, cosh, tanh, arctanh, log, exp, square root and even multiply and divide. the method dates back to volder [1959], and due to its versatility and compactness, it made possible the microcoding of the hp35 pocket scientific calculator in 1972. here is some code to illustrate the techniques. ive split the methods into three parts linear, circular and hyperbolic. in the hp35 microcode these would be unified into one function (for space reasons). because the linear mode can perform multiply and divide, you only need add/subtract and shift to complete the implementation. you can select in the code whether to do the multiples and divides also by cordic means. other multiplies and divides are all powers of 2 (these dont count). to eliminate these too, would involve ieee hackery.
標簽： essentially algorithm describe suitably
上傳時間： 2017-03-02
上傳用戶：litianchu
