Kiss FFT is a small and simple FFT library. It has no complicated platform-specific optimizations, can do either fixed or floating point with just a recompile, and is efficient enough for all but the most demanding applications.
This guide explains how data networks operate, why data systems are becoming more complicated, and how data networks are changing to permit broadband services and applications.
Table of Contents
Introduction To Data Networks—PDN, LAN, MAN, WAN, and Wireless Data, Technologies and Systems
Data Networks
List of Figures
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
便攜式信號采集在機器健康診斷系統中有較高的應用價值。機器健康診斷的信號特點是包括低頻信號。本文研究是為了實現簡易而且低成本的低頻便攜式信號采集。以Microchip公司單片機PIC18F1320為核心設計信號采集電路，實現了信號的采集和保存。系統采用串行電可擦除芯片24LC32A保存數據，經過有線通信，信號數據由串行口通過MAX232芯片輸送到微型計算機接收和保存，最后繪制出信號波形。 微型計算機程序采用Visual Basic編程。研究成功采樣頻率為3 kHz的復雜信號，證明該方案符合設計要求。
Abstract:
Portable signal acquisition is useful in machine health monitoring systems. The signal characteristics of machine health monitoring includes low frequency signals. The goal of this study is to realize simple, inexpensive and portable low frequency signal sampling. This paper provides the project of signal acquisition system design based on PIC18F1320 microcontroller manufactured by the Microchip Technology Incorporation to achieve signal sampling and storage. The system adopted EEPROM 24LC32A to store the signal data. The microcomputer received data via wired link with the MAX232 IC through the serial port. The microcomputer program, programmed in Visual Basic, received the data, stored it and plotted the signal. The study successfully samples 3kHz complicated signals and thus meets the design requirement.
Open Source for the Enterprise
Open source software is changing the world of Information Technology. But making it work for your company is far more complicated than simply installing a copy of Linux. If you are serious about using open source to cut costs, accelerate development, and reduce vendor lock-in, you must institutionalize skills and create new ways of working. You must understand how open source is different from commercial software and what responsibilities and risks it brings. Open Source for the Enterprise is a sober guide to putting open source to work in the modern IT department.
Readers can pick up this book and become familiar with C++ in a short time. Stan has taken a very broad and complicated topic and reduced it to the essentials that budding C++ programmers need to know to write real programs. His case study is effective and provides a familiar thread throughout the book.
This cookbook contains a wealth of solutions to problems that SQL programmers face all the time. Recipes inside range from how to perform simple tasks, like importing external data, to ways of handling issues that are more complicated, like set algebra. Each recipe includes a discussion that explains the logic and concepts underlying the solution. The book covers audit logging, hierarchies, importing data, sets, statistics, temporal data, and data structures.
Executing a DTS package is very simple, in its simplest form the execution contains for 3 steps. These 3 steps form the foundation for all more complicated forms for package execution.
