為滿足無線網絡技術具有低功耗、節點體積小、網絡容量大、網絡傳輸可靠等技術要求，設計了一種以MSP430單片機和CC2420射頻收發器組成的無線傳感節點。通過分析其節點組成，提出了ZigBee技術中的幾種網絡拓撲形式，并研究了ZigBee路由算法。針對不同的傳輸要求形式選用不同的網絡拓撲形式可以盡大可能地減少系統成本。同時針對不同網絡選用正確的ZigBee路由算法有效地減少了網絡能量消耗，提高了系統的可靠性。應用試驗表明，采用ZigBee方式通信可以提高傳輸速率且覆蓋范圍大，與傳統的有線通信方式相比可以節約40%左右的成本。 Abstract: To improve the proposed technical requirements such as low-ower， small nodes， large capacity and reliable network transmission， wireless sensor nodes based on MSP430 MCU and CC2420 RF transceiver were designed. This paper provided network topology of ZigBee technology by analysing the component of the nodes and researched ZigBee routing algorithm. Aiming at different requirements of transmission mode to choose the different network topologies form can most likely reduce the system cost. And aiming at different network to choose the correct ZigBee routing algorithm can effectively reduced the network energy consumption and improved the reliability of the system. Results show that the communication which used ZigBee mode can improve the transmission rate， cover more area and reduce 40% cost compared with traditional wired communications mode.
標簽： ZigBee 無線傳感網絡 協議研究 路由
上傳時間： 2013-10-09
上傳用戶：robter
針對UHF讀寫器設計中，在符合EPC Gen2標準的情況下，對標簽返回的高速數據進行正確解碼以達到正確讀取標簽的要求，提出了一種新的在ARM平臺下采用邊沿捕獲統計定時器數判斷數據的方法，并對FM0編碼進行解碼。與傳統的使用定時器定時采樣高低電平的FM0解碼方法相比，該解碼方法可以減少定時器定時誤差累積的影響；可以將捕獲定時器數中斷與數據判斷解碼相對分隔開，使得中斷對解碼影響很小，實現捕獲與解碼的同步。通過實驗表明，這種方法提高了解碼的效率，在160 Kb/s的接收速度下，讀取一張標簽的時間約為30次/s。 Abstract: Aiming at the requirement of receiving correctly decoded data from the tag under high-speed communication which complied with EPC Gen2 standard in the design of UHF interrogator， the article introduced a new technology for FM0 decoding which counted the timer counter to judge data by using the edge interval of signal capture based on the ARM7 platform. Compared with the traditional FM0 decoding method which used the timer timed to sample the high and low level， the method could reduce the accumulation of timing error and could relatively separate capture timer interrupt and the data judgment for decoding， so that the disruption effect on the decoding was small and realizd synchronization of capture and decoding. Testing result shows that the method improves the efficiency of decoding， at 160 Kb/s receiving speed， the time of the interrogator to read a tag is about 30 times/s.
上傳時間： 2013-11-10
上傳用戶：liufei
通過比較各種隔離數字通信的特點和應用范圍，指出塑料光纖在隔離數字通信中的優勢。使用已經標準化的TOSLINK接口，有利于節省硬件開發成本和簡化設計難度。給出了塑料光纖的硬件驅動電路，說明設計過程中的注意事項，對光收發模塊的電壓特性和頻率特性進行全面試驗，并給出SPI口使用塑料光纖隔離通信的典型應用電路圖。試驗結果表明，該設計可為電力現場、電力電子及儀器儀表的設計提供參考。 Abstract: y comparing characteristics and applications area of various isolated digital communications， this article indicates advantages of plastic optical fiber in isolated digital communications. Using the standardized TOSLINK interface， it helps to control costs and difficulty in hardware development and design. Then it gives the hardware driver circuit of plastic optical fiber module， explains the noticed details in design process， gives results on the basis of the optical transceiver module voltage characteristics and frequency characteristics tests. Finally，it gives typical application circuit of the SPI communication port by using plastic optical fiber isolation .The results show that this design can be referenced for the power field， power electronics and instrumentation design.
上傳時間： 2014-01-10
上傳用戶：gundan
同步技術是跳頻通信系統的關鍵技術之一，尤其是在快速跳頻通信系統中，常規跳頻通信通過同步字頭攜帶相關碼的方法來實現同步，但對于快跳頻來說，由于是一跳或者多跳傳輸一個調制符號，難以攜帶相關碼。對此引入雙跳頻圖案方法，提出了一種適用于快速跳頻通信系統的同步方案。采用短碼攜帶同步信息，克服了快速跳頻難以攜帶相關碼的困難。分析了同步性能，仿真結果表明該方案同步時間短、虛警概率低、捕獲概率高，同步性能可靠。 Abstract: Synchronization is one of the key techniques to frequency-hopping communication system， especially in the fast frequency hopping communication system. In conventional frequency hopping communication systems， synchronization can be achieved by synchronization-head which can be used to carry the synchronization information， but for the fast frequency hopping， Because modulation symbol is transmitted by per hop or multi-hop， it is difficult to carry the correlation code. For the limitation of fast frequency hopping in carrying correlation code， a fast frequency-hopping synchronization scheme with two hopping patterns is proposed. The synchronization information is carried by short code， which overcomes the difficulty of correlation code transmission in fast frequency-hopping. The performance of the scheme is analyzed， and simulation results show that the scheme has the advantages of shorter synchronization time， lower probability of false alarm， higher probability of capture and more reliable of synchronization.
標簽： 快速跳頻 同步技術 通信系統
上傳時間： 2013-11-23
上傳用戶：mpquest
提出了一種以ARM微處理器為控制核心的遠程無線視頻監控終端的設計方案，其監控終端的硬件設計包括視頻采集處理、中央管理控制、無線傳輸3個模塊。并給出了監控終端的軟件開發平臺和開發模式的系統啟動代碼、嵌入式Linux系統移植以及驅動程序和應用程序。測試結果表明，該監控終端設計方案合理、有效，基本滿足監控需求。 Abstract: A remote wireless video monitoring terminal design， which uses ARM microprocessor as its core control， is proposed in this paper.The hardware design of monitoring terminal system is composed of the video acquisition and processing module， the central management and control module， wireless transmission module.Meanwhile the monitoring terminal-s software development platform and development patterns are designed. Also the design of the system-s start codes， embedded Linux system-s transplantation process， driver and the corresponding applications are given. The results showed that the monitoring terminal design is reasonable， effective， basically meet monitoring requirements.
標簽： ARM 遠程無線 視頻監控 終端設計
上傳時間： 2013-11-13
上傳用戶：wanqunsheng
一個24c16的讀寫程序（已經調試過）(arens) //////////////////////////////////////////////////////////////// //24c16讀寫驅動程序，F(xiàn)M24C16A-AT24C16中文資料pdf //=-------------------------------------------------------------------------------/*模塊調用:讀數據:read(unsigned int address)寫數據:write(unsigned int address,unsigned char dd) dd為要寫的 數據字節*///---------------------------------------------------------------------------------- sbit sda=P3^0;sbit scl=P3^1; sbit a0=ACC^0; //定義ACC的位，利用ACC操作速度最快sbit a1=ACC^1;sbit a2=ACC^2;sbit a3=ACC^3;sbit a4=ACC^4;sbit a5=ACC^5;sbit a6=ACC^6;sbit a7=ACC^7; //--------------------------------------------------------------------------------------#pragma disablevoid s24(void) //起始函數{_nop_(); scl=0; sda=1; scl=1; _nop_(); sda=0; _nop_(); _nop_(); scl=0; _nop_(); _nop_(); sda=1;
上傳時間： 2013-10-31
上傳用戶：fdfadfs
針對嵌入式機器視覺系統向獨立化、智能化發展的要求，介紹了一種嵌入式視覺系統--智能相機。基于對智能相機體系結構、組成模塊和圖像采集、傳輸和處理技術的分析，對國內外的幾款智能相機進行比較。綜合技術發展現狀，提出基于FPGA+DSP模式的硬件平臺，并提出智能相機的發展方向。分析結果表明，該系統設計可以實現脫離PC運行，完成圖像獲取與分析，并作出相應輸出。 Abstract: This paper introduced an embedded vision system-intelligent camera ，which was for embedded machine vision systems to an independent and intelligent development requirements. Intelligent camera architecture， component modules and image acquisition， transmission and processing technology were analyzed. After comparing integrated technology development of several intelligent cameras at home and abroad， the paper proposed the hardware platform based on FPGA+DSP models and made clear direction of development of intelligent cameras. On the analysis of the design， the results indicate that the system can run from the PC independently to complete the image acquisition and analysis and give a corresponding output.
上傳時間： 2013-11-14
上傳用戶：無聊來刷下
針對傳統集成電路（ASIC）功能固定、升級困難等缺點，利用FPGA實現了擴頻通信芯片STEL-2000A的核心功能。使用ISE提供的ddS IP核實現NCO模塊，在下變頻模塊調用了硬核乘法器并引入CIC濾波器進行低通濾波，給出了DQPSK解調的原理和實現方法，推導出一種簡便的引入?仔/4固定相移的實現方法。采用模塊化的設計方法使用VHDL語言編寫出源程序，在Virtex-II Pro 開發板上成功實現了整個系統。測試結果表明該系統正確實現了STEL-2000A的核心功能。 Abstract: To overcome drawbacks of ASIC such as fixed functionality and upgrade difficulty, FPGA was used to realize the core functions of STEL-2000A. This paper used the ddS IP core provided by ISE to realize the NCO module, called hard core multiplier and implemented CIC filter in the down converter, described the principle and implementation detail of the demodulation of DQPSK, and derived a simple method to introduce a fixed phase shift of ?仔/4. The VHDL source code was designed by modularity method , and the complete system was successfully implemented on Virtex-II Pro development board. Test results indicate that this system successfully realize the core function of the STEL-2000A.
上傳時間： 2013-11-19
上傳用戶：neu_liyan
為了在CDMA系統中更好地應用QDPSK數字調制方式，在分析四相相對移相（QDPSK)信號調制解調原理的基礎上，設計了一種QDPSK調制解調電路，它包括串并轉換、差分編碼、四相載波產生和選相、相干解調、差分譯碼和并串轉換電路。在MAX+PLUSⅡ軟件平臺上，進行了編譯和波形仿真。綜合后下載到復雜可編程邏輯器件EPM7128SLC84-15中，測試結果表明，調制電路能正確選相，解調電路輸出數據與QDPSK調制輸入數據完全一致，達到了預期的設計要求。 Abstract: In order to realize the better application of digital modulation mode QDPSK in the CDMA system， a sort of QDPSK modulation-demodulation circuit was designed based on the analysis of QDPSK signal modulation-demodulation principles. It included serial/parallel conversion circuit, differential encoding circuit, four-phase carrier wave produced and phase chosen circuit, coherent demodulation circuit, difference decoding circuit and parallel/serial conversion circuit. And it was compiled and simulated on the MAX+PLUSⅡ software platform,and downloaded into the CPLD of EPM7128SLC84-15.The test result shows that the modulation circuit can exactly choose the phase，and the output data of the demodulator circuit is the same as the input data of the QDPSK modulate. The circuit achieves the prospective requirement of the design.
上傳時間： 2013-10-28
上傳用戶：jyycc
波長信號的解調是實現光纖光柵傳感網絡的關鍵，基于現有的光纖光柵傳感器解調方法，提出一種基于FPGA的雙匹配光纖光柵解調方法，此系統是一種高速率、高精度、低成本的解調系統，并且通過引入雙匹配光柵有效地克服了雙值問題同時擴大了檢測范圍。分析了光纖光柵的測溫原理并給出了該方案軟硬件設計，綜合考慮系統的解調精度和FPGA的處理速度給出了基于拉格朗日的曲線擬合算法。 Abstract: Sensor is one of the most important application of the fiber grating. Wavelength signal demodulating is the key techniques to carry out fiber grating sensing network， based on several existing methods of fiber grating sensor demodulation inadequate， a two-match fiber grating demodulation method was presented. This system is a high-speed， high precision， low-cost demodulation system. And by introducing a two-match grating effectively overcomes the problem of double value while expands the scope of testing. This paper analyzes the principle of fiber Bragg grating temperature and gives the software and hardware design of the program. Considering the system of demodulation accuracy and processing speed of FPGA，this paper gives the curve fitting algorithm based on Lagrange.
標簽： FPGA 光纖光柵 解調系統
上傳時間： 2013-10-10
上傳用戶：zxc23456789
