Make and answer phone calls Detect tone and pulse digit from the phone line Capture Caller ID Support blind transfer, single-step transfer/conference, consultation transfer/conference, hold, unhold. Control of the local phone handset, microphone and speaker of the modem Send and receive faxes Play and record on the phone line or sound card Play music in background mode Silence detection VU Meter Wave sound editor that allows your end-users to edit their own sound files. Voice recognition and voice synthesis. Full control over the serial port device ZModem file transfer utility File compression and encryption utility
上傳時間： 2013-11-30
上傳用戶：水中浮云
This a simple bootloader for AT91SAM7{S,X}{64,128,256} processors. It permits you to download new code to the device over USB. This bootrom is installed at address 0x00000000 in the ARM, which means that it is the first piece of code to execute after reset. At startup, it waits for a few seconds to see if the downloader is trying to connect. If not, then the bootloader gives up control and jumps to your program. If the downloader is trying to connect, then the bootloader receives the new program over USB and writes it into flash.
標簽： bootloader processors download permits
上傳時間： 2015-11-30
上傳用戶：shus521
Hey. This some pid code for the atmega88 that I once used to control a heater. It s purpose is pretty specific, and I only wrote it to work on the mega88, so the code itself won t be too useful. It is a good place to start if you re trying to use or figure out pid though.
標簽： control purpose atmega heater
上傳時間： 2013-12-19
上傳用戶：天誠24
The development of a data acquisition card based on USB bus is introduced in this article.It first describes the configuration and principle of this card in the part of hardware design,and then the application program and device driver in the part of software design.Data acquisition program in firmware is also discussed.Finally,this data acquisition card is tested and evaluated in a program developed by Lab Windows CVI,which shows that this car is stable and reliable
標簽： development acquisition introduced article
上傳時間： 2015-12-07
上傳用戶：lijianyu172
電子書388頁，英文的。 Guide toWriting and Porting Device Drivers VxWorks5.3設備驅動編寫和移植
上傳時間： 2015-12-08
上傳用戶：sssl
Universal Serial Bus (USB) is a communications architecture that gives a personal computer (PC) the ability to interconnect a variety of devices using a simple four- wire cable. The USB is actually a two-wire serial communication link that runs at either 1.5 or 12 megabits per second (mbs). USB protocols can configure devices at startup or when they are plugged in at run time. These devices are broken into various device classes. Each device class defines the common behavior and protocols for devices that serve similar functions. Some examples of USB device classes are shown in the following table
標簽： communications architecture Universal computer
上傳時間： 2015-12-08
上傳用戶：stvnash
Triscend supports the use of the Model Technology ModelSim logic simulator for VHDL simulation of designs implemented in the Configurable System Logic (CSL) portion of a Triscend device.
標簽： Technology simulation simulator the
上傳時間： 2013-12-26
上傳用戶：zl5712176
This application report describes the use of Timer_A3 to decode RC5 and SIRC TV IR remote control signals. The decoder described in this report is interrupt-driven and operates a background function using specific features the Timer_A3. Only a small portion of the MSP430 CPU?s nonreal-time resources is used. Specific hardware bit-latching capabilities of the Timer_A3 module are used for real-time decoding of the IR data signal, independent and asynchronous to the CPU. CPU activity and power consumption are kept to an absolute minimum level. The Timer_A3 decoder implementation also allows other tasks to occur simultaneously if required. The solutions provided are written specifically for MSP430x11x(1) and MSP430x12x derivatives, but can be adapted to any other MSP430 incorporating Timer_A3. 電視遙控器設計基於MSP430
標簽： application describes Timer_A control
上傳時間： 2014-01-01
上傳用戶：qq21508895
1 安裝：首先安裝MPLAB IDE V7.42的程序，然后再安裝C的組件PICC8.05-PL.安裝過程中全部確認選擇，完畢后重啟計算機。 2 激活：(PICC8.05-PL) 運行“開始”菜單下的“HI-TECH SOFTWARE”中的 激活（Complier Activation）程序， 再同時啟動算號器程序（HtkeyGen.exe）,將Last Name前的勾去掉，填入公司名稱，算出相應內 容填入激活程序相應欄目，OK即可完成激活。 3 設置： 3.1 將MPLAB 7.42啟動后，在文件欄中打開C的桌面項目文件，在Project欄目中 檢查 select language Toolsuite...中的選項，所有路徑須指向安裝路徑如C:\HT-PIC\BIN\PICC.EXE； 3.2 在Project欄目中檢查 setlanguage Tool Locations中的HI-TECH ToolsuiteXDGR 相關選項，executables中各程序應指向picc.exe Default Search Paths & Directories中 的相關路徑應為安裝目錄如C:\HT-PIC\include 和C:\HT-PIC\lib； 3.3 設置programmer中的select programmer選項為"MPLAB IED 2"（經驗：如果不打開編譯器，此選項無法選中）。 3.4 設置單片機型號，在Congfigure中的Select Device選擇準確的芯片型號；
上傳時間： 2016-01-01
上傳用戶：Ants
Example to support XML files using MSXML. ========================================= XML (Extensible Markup Language) is a commonly used basis for representing a huge range of structured data file formats. The specification is maintained by the World Wide Web Consortium (W3C?. This plugin is intended as an example of how XML data can be read with a DataPlugin. You can adjust it to meet the needs of your own XML file format. After installing the URI file (double click on it), you can find the VBScript file located at "C:\Program Files\National Instruments\Shared\USI\plugins\DataPlugins\XML Example" You can make changes to this file to read your specific XML file.
標簽： XML Example support Extensi
上傳時間： 2016-01-03
上傳用戶：cooran
蟲蟲下載站版權所有 京ICP備2021023401號-1
