C8051F020單片機通過SPI接口驅動四線電阻式觸摸屏控制器TSC2046，利用中斷方式驅動TSC2046設計軟件。介紹了觸摸屏的工作原理、TSC2046工作方式以及典型應用電路。
Abstract:
The C8051F020 MCU is connected with the TSC2046 which is a 4-wire touch screen controller. The TSC2046 is controlled by interrupt mode, the? operation principle of touch screen is introduced. The operation mode of TSC2046 and typical application circuit are also discussed.
介紹了MPC555與CS8900A擴展以太網的硬件設計圖。以NUCLUES PLUS操作系統為基礎，介紹了網卡軟件驅動程序的編制，給出了以太網協議包嵌入NUCLEUS PLUS操作系統的實現方法。
Abstract:
The Ethernet extension hardware design of MPC555 and CS8900A are introduced,and the software driven program based on NUCLEUS PLUS operation system and the technique that Ethernet protocol embedded in NUCLEUS PLUS real operation system are discussed.
介紹基于ATmega8型單片機的溫度測量及加熱控制系統。分析系統的工作原理，詳盡討論系統的硬件電路和軟件流程。實驗證明，該系統工作可靠，穩定性高。
Abstract:
The new temperature measuring and heating control system based on ATmega8 MCU is introduced.The system’s working principles is analyzed.The design principles of hardware and software are also discussed in detail.This system has been testified and it works steady and reliably.
介紹了CAN總線和P87C591單片機的特點，給出了基于P87C591單片機的信號采集節點的軟、硬件設計，指出了硬件電路設計中應注意的問題，在軟件設計中重點介紹了節點初始化、報文發送和報文接收等子程序。
Abstract:
The features of CAN Bus and the microcontroller P87C591 are introduced, and the design of hardware circuit and soft configuration of the signals collection node based on P87C591 are presented. The problems in designing hardware circuit are discussed.Initialization subprogram, transmiting subprogram and receiving subprogram are emphasized in soft configuration.
PICkit™ 2 Microcontroller Programmer USER’S GUIDE
This chapter contains general information that will be useful to know before using thePICkit™ 2 Microcontroller Programmer. Items discussed in this chapter include:• Document Layout• Conventions Used in this Guide• Warranty Registration• Recommended Reading• The Microchip Web Site• Development Systems Customer Change Notification Service• Customer Support• Document Revision History
The PCA9555 is a 24-pin CMOS device that provides 16 bits of General Purpose parallelInput/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed toenhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvementsinclude higher drive capability, 5 V I/O tolerance, lower supply current, individual I/Oconfiguration, and smaller packaging. I/O expanders provide a simple solution whenadditional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.The PCA9555 consists of two 8-bit Configuration (Input or Output selection); Input, Outputand Polarity Inversion (active HIGH or active LOW operation) registers. The systemmaster can enable the I/Os as either inputs or outputs by writing to the I/O configurationbits. The data for each Input or Output is kept in the corresponding Input or Outputregister. The polarity of the read register can be inverted with the Polarity Inversionregister. All registers can be read by the system master. Although pin-to-pin and I2C-busaddress compatible with the PCF8575, software changes are required due to theenhancements, and are discussed in Application Note AN469.
基于P87 C591的CAN總線系統智能節點設計Design of CAN System Intelligent Node Based on P87C591
給出了基于帶CAN控制器的單片8位微控制器P87C591的智能節點的硬件電路及軟件結構，詳細介紹了設計中的難點及實現過程中應注意的問題。關鍵詞:CAN總線;智能節點
Abstract:A h ardc ircuita nds oftw arec onfigurationo fth ei ntelligentnode based on a microcontroller with CAN controller P87C591 arepresented.E speciallyt hec ruxi nd esigninga ndt hep roblemst hatshould be paid attention in realizing are discussed in details.Keyw ords:C AN;in telligentn ode
CA N 總線 是德國Bosch從20世紀80年代初為解決現代汽車中眾多的控制與測試儀器之間的數據交換而開發的一種串行數據通信協議，它是一種多主總線，通信介質可以是雙絞線、同軸電纜或光導纖維。由于CAN總線具有較強的糾錯能力，支持差分收發，因而適合高噪聲環境。并具有較遠的傳輸距離，適用于許多領域的分布式測控系統。目前已在工業自動化、建筑物環境控制、醫療設備等許多領域得到廣泛的應用。CAN已成為國際標準化組織IS011898標準。
基于多點網絡的水廠自動監控系統設計Design of MPI Based Automatic Monitoring and Control System in Water Works劉 美 俊(湖南工程學院，湘潭411101)摘要針對水廠工作水泵多、現場離控制站距離遠的特點，提出了一種基于MPI多點網絡的自動監控系統的設計方法，分析了系統的工作原理，介紹了系統中數據的采集與處理、主站與從站的通信原理以及系統軟件的設計。由于這種系統的主、從站PLC之間采用MPI網絡通信，具有運行可靠、性能價格比高的特點，所以適用于中小規模水廠的分布式監控場合。關鍵詞多點網絡主站從站監控系統Abstract Ina ccordancew ithth efe atuersof w aterw orks,i. e. ，manyp umpsin o perationa ndth ep umps， farfor mt hec ontrolst ation,th em ethodo fdesigninga na utomati(〕monitoringa ndc ontorlsy stemb asedo nM PIis p resented.Th eo perationalpr incipleo fth esy stemi san alyzed,th ed atac olection,data processing; communication between master station and slave station as wel as design and system software are discussed. Because MPI network communicationis used among master station, slave stations and PLC, the system is reliable and high cost-efective. It is， suitable for smal and mediumsized water works for distrbuted monitoring and control.Keywords MPI Masterst ation Slaves tation Monitoringa ndc ontorlsy stem
自來 水 廠 的自動控制系統一般分為兩大部分，一對組態硬件要求較高，投資較大。相對而言，MPI網是水源地深水泵的工作控制，一是水廠區變頻恒壓供絡速度可達187.5 M bps，通過一級中繼器傳輸距離可水控制，兩部分的實際距離通常都比較遠。某廠水源達Ikm 。根據水廠的具體情況，確定以MPI方式組地有3臺深井泵給水廠區的蓄水池供水。水廠區的成網絡，主站PLC為S7-300系列的CPU3121FM，從任務是對水池的水進行消毒處理后，通過加壓泵向管站為S7-200系列的CPU222。這樣既滿足了系統要路恒壓供水。選用Siemens公司的S7系列可編程控求，又相對于Profibus網絡節省了三分之一的成本，制器(PLC)和上位機組成實時數據采集和監控系統， 這種分布式監控系統具有較高的性能價格比。系統對深水泵進行遠程控制，對供水泵采用變頻器進行恒中PLC的物理層采用RS - 485接口，網絡延伸選用壓控制以保證整個水廠的電機設備安全、可靠地運帶防雷保護的中繼器，使系統的安全運行得到了保行。證。MPI網絡的拓撲結構如圖1所示。1 多點網絡(NWI)監控系統的組成Sie me ns 公司S7系列PLC通常有MP」多點網絡與Profibus現場總線網絡兩種組網方式。Profibus現場總線的應用目前較為普遍，通用性較好，它由Profibus一DP, Profibus一FMS, Profibus一PA組成。Profibus - DP型用于分散外設間的數據傳輸，傳輸速率為9.6kbps一12Mbps，主要用于現場控制器與分散1/0之間的通信，可滿足交直流調速系統快速響應的時間要求，特別適合于加工自動化領域的應用;Profibus - FMS主要解決車間級通信問題，完成中等傳輸速度的循環或非循環數據交換任務，適用于紡織、樓宇自動化、可編程控制器、低壓開關等;Profibus - PA型采用了OSI模型的物理層和數據鏈路層，適用于過程自動化的總線類型。
針對運行中火車測速運用多普勒效應采用DSP 設計雷達測速系統并闡述了其基本設計思想與工作原理給出系統硬件軟件設計結構和原理圖改善了原有光電測速精度提高了系統工作穩定性和可靠性經實驗證明DSP 采集板工作穩定測速效果好關鍵詞DSP; 雷達測速; 多普勒效應
On Board DSP-Based Radar Speed Measurement System TANG Wei, SUN Zhi-fang, CHEN Quan (Dept.of computer Science,Yangtze University,Jingzhou 434023,China)Abstract: This paper presents a DSP-based train speed measurement by using Doppler radar. The structure of the system is introduced.The hardware and software are also discussed.Key words: DSP; rader speed measurement; doppler principle
Abstract: This application note discusses the development and deployment of 3G cellular femtocell base stations. The technicalchallenges for last-mile residential connectivity and adding system capacity in dense urban environments are discussed, with 3Gfemtocell base stations as a cost-effective solution. Maxim's 3GPP TS25.104-compliant transceiver solution is presented along withcomplete radio reference designs such as RD2550. For more information on the RD2550, see reference design 5364, "FemtocellRadio Reference Designs Using the MAX2550–MAX2553 Transceivers."
