Using the XGATE for Manchester DecodingTable of Contents
1 Introduction 1.1 XGATE Module in S12X 2 Decoding Algorithm 3 Software Implementation 3.1 Frame Scheme 3.2 Operating Modes and Demo 3.3 Files Summary 3.4 Complete Mode Flowchart 4 Manchester Encoder 4.1 Devices Used 5 Conclusion Appendix A Noise Elements During RF Transmissions in the Manchester Decoding ImplementationA.1 Types of Noise A.2 Effects of Noise A.3 Workaround for Noise Effects
This application note describes how to decode standard DTMF tones using the minimum number of external discrete components and a PIC. The two examples use a PIC which has an 8 bit timer and either a comparator or an ADC, although it can be modified for use on a PIC which has only digital I/O. The Appendices have example code for the 16C662 (with comparator) and 16F877 (using the ADC).
As the majority of the Digital Signal Processing is done in software, little is required in the way of external signal conditioning. Software techniques are used to model the individual elements of a DTMF Decoder IC.
摘要:本水位監測報警器使用5V低壓直流電源(也可以用3節5號電池代替)就可以對5~15厘米的水位進行監測,用LED顯示和數碼管顯示水位,并可以對不再此范圍內的水位發出報警。主要采用CD4066、74LS86、74LS32、CD4511芯片,再加上數碼管、蜂鳴器、發光二極管、電阻這些器件組成一個簡單而靈敏的監測報警電路,操作簡單,接通電源即可工作。因為大部分電路采用數字電路,所以本水位監測報警器還具有耗能低、準確性高的特點。關鍵字:譯碼電路 報警電路 監測電路
Abstract: The water level alarm monitoring the use of 5 V low-voltage DC power (can also use three batteries replaced on the 5th) will be able to 5 to 15 centimeters of water level monitoring, with LED display and digital display of water level, and this can no longer Within the scope of a water level alarm. Mainly CD4066, 74LS86, 74LS32, CD4511 chips, coupled with digital control, buzzer, light-emitting diode, the resistance of these devices composed of a simple and sensitive monitoring alarm circuits. Because the majority of circuits using digital circuitry, so the water level monitored alarm system also has low energy consumption, high accuracy of the characteristics.
Keyword: Decoding circuit alarm circuit monitoring circuit
針對UHF讀寫器設計中,在符合EPC Gen2標準的情況下,對標簽返回的高速數據進行正確解碼以達到正確讀取標簽的要求,提出了一種新的在ARM平臺下采用邊沿捕獲統計定時器數判斷數據的方法,并對FM0編碼進行解碼。與傳統的使用定時器定時采樣高低電平的FM0解碼方法相比,該解碼方法可以減少定時器定時誤差累積的影響;可以將捕獲定時器數中斷與數據判斷解碼相對分隔開,使得中斷對解碼影響很小,實現捕獲與解碼的同步。通過實驗表明,這種方法提高了解碼的效率,在160 Kb/s的接收速度下,讀取一張標簽的時間約為30次/s。
Abstract:
Aiming at the requirement of receiving correctly decoded data from the tag under high-speed communication which complied with EPC Gen2 standard in the design of UHF interrogator, the article introduced a new technology for FM0 decoding which counted the timer counter to judge data by using the edge interval of signal capture based on the ARM7 platform. Compared with the traditional FM0 decoding method which used the timer timed to sample the high and low level, the method could reduce the accumulation of timing error and could relatively separate capture timer interrupt and the data judgment for decoding, so that the disruption effect on the decoding was small and realizd synchronization of capture and decoding. Testing result shows that the method improves the efficiency of decoding, at 160 Kb/s receiving speed, the time of the interrogator to read a tag is about 30 times/s.
One of the strengths of Synplify is the Finite State Machine compiler. This is a powerfulfeature that not only has the ability to automatically detect state machines in the sourcecode, and implement them with either sequential, gray, or one-hot encoding. But alsoperform a reachability analysis to determine all the states that could possibly bereached, and optimize away all states and transition logic that can not be reached.Thus, producing a highly optimal final implementation of the state machine.
One of the most important issues affecting
the implementation of microcontroller
software deals with the data-decision
algorithm. Data-decision refers to decoding
the DIO-pin from the CC400/CC900. Two
main principles exist for decoding
Manchester-coded data: Data decision
based on timing the period between
transitions, and data decision based on
oversampling.
This packet is a IS-95 baseband simulation for 1 data channel of 9.6 KBps rate. The simulation is written for static channel and AWGN noise.
The packet include:
1) Packet Builder (Viterbi Encoding, Interleaver, PN generation)
2) Modulator (RRC filter)
3) Demodulator (Matched Filter, RAKE receiver)
4) Receiver (HD or SD) (Deinterleaver, Viterbi Decoder).
You should run "Simulation.m" function that include all modules.
I. Introduction
This code exploits a previously undisclosed vulnerability in the bit string
decoding code in the Microsoft ASN.1 library. This vulnerability is not related
to the bit string vulnerability described in eEye advisory AD20040210-2. Both
vulnerabilities were fixed in the MS04-007 patch.
II. Screenshots
$ ./kill-bill.pl
. kill-bill : Microsoft ASN.1 remote exploit for CAN-2003-0818 (MS04-007)
by Solar Eclipse <solareclipse@phreedom.org>
Usage: kill-bill -p <port> -s <service> host
Services:
iis IIS HTTP server (port 80)
iis-ssl IIS HTTP server with SSL (port 443)
exchange Microsoft Exchange SMTP server (port 25)
smb-nbt SMB over NetBIOS (port 139)
smb SMB (port 445)
If a service is running on its default port you don t have to
specify both the service and the port.
Examples: kill-bill -s iis 192.168.0.1
kill-bill -p 80 192.168.0.1
kill-bill -p 1234 -s smb 192.168.0.1
The two C source files in this archive are specific to the TRS-80 Model 4 with
high-resolution graphics board. However, the code which performs Huffman enco-
ding and decoding is of general interest.