symbian s60 end to end socket程序源碼 基于第二版何第三版的sdk
上傳時間： 2014-11-23
上傳用戶：chenjjer
The WCDMA Physical Layer Demo consists of an end-to-end (transmitter-to-receiver) simulation of the Frequency Division Duplex (FDD) Downlink physical layer for several Dedicated Channels (DCH) as specified by the 3GPP standard (Release 99).
標簽： transmitter-to-receiver end-to-end simulation Physical
上傳時間： 2013-11-28
上傳用戶：gdgzhym
In the last three articles, I’ve been walking you through the creation of an end-to-end BlackBerry application that will serve as a mobile front-end to my Knowledge Base sample web application.
標簽： BlackBerry end-to-end the articles
上傳時間： 2014-01-25
上傳用戶：kristycreasy
The UMTS Physical Layer model consists of an end-to-end (transmitter-to-receiver) simulation of the Frequency Division Duplex (FDD) Downlink physical layer for several Dedicated Channels (DCH) as specified by the 3GPP standard (Release 99).
標簽： transmitter-to-receiver end-to-end simulation Physical
上傳時間： 2014-01-11
上傳用戶：it男一枚
This code is just a front-end to source separation algorithms.
標簽： algorithms separation front-end source
上傳時間： 2014-01-21
上傳用戶：z754970244
a good time to end progress bar for MFC
上傳時間： 2016-02-07
上傳用戶：hj_18
adhoc路由協議aodv仿真與end-to-en-delay分析
標簽： end-to-en-delay adhoc aodv 路由協議
上傳時間： 2016-06-21
上傳用戶：tyler
This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
標簽： pci PCB 設計規范
上傳時間： 2013-10-15
上傳用戶：busterman
Abstract: A resistive feedback network is often used to set the output voltage of a power supply. A mechanical potentiometer (pot)conveniently solves the problem of adjusting a power supply. For easier automatic calibration, a mechanical pot can be replaced witha digital pot. This application note presents a calibration solution that uses a digital pot, because digipots are smaller, do not movewith age or vibration, and can be recalibrated remotely. This proposed solution reduces the susceptibility of the system to thetolerance of the digital pot's end-to-end resistance, making the solution optimal fordesigners. This application note also explainssome of the equations required to calculate the resistor chain values and to use a digital pot in this way. A spreadsheet withstandard reisistor values is available for easy calculations.
標簽： 電源供應器 數字電位器 應用筆記 校準
上傳時間： 2013-10-31
上傳用戶：caiguoqing
This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
標簽： pci PCB 設計規范
上傳時間： 2014-01-24
上傳用戶：s363994250
蟲蟲下載站版權所有 京ICP備2021023401號-1
