ArtFormula package contains two nonvisual Delphi component for symbolic expression parsing and evaluation. Provides runtime scripting engine for automating your programs.
FIBPlus is a component suite intended for work with InterBase. It is direct, fast and flexible InterBase connectivity for Delphi, C++ Builder, Ada and Kylix. FIBPlus supports Delphi 5-7, Delphi 2005, Delphi 2006, Delphi 2007, C++ Builder 5-6, C++ Builder 2006, C++ Builder 2007, Kylix 3, gnat-3.15p, gnat2006 GPL, and all versions of InterBase 4.x-7.x, InterBase 2007 and Firebird 1.x-2.x.
Using FIBPlus in your applications you do not need to install any additional software except for InterBase Client Software. FIBPlus supports all special InterBase features such as array-fields, event alerters, BLOB-fields, etc.
FIBPlus is a native component set and its evaluation versions are distributed partially in sources.
Registering FIBPlus you get full sources of components and technical support
This SPI-mode SD Card controller is a free SOPC Builder component that can be used in any SOPC Builder system. The included example design runs on the Nios II Embedded evaluation Kit, Cyclone III edition (NEEK).
This SPI-mode SD Card controller is a free SOPC Builder component that can be used in any SOPC Builder system. The included example design runs on the Nios II Embedded evaluation Kit, Cyclone III edition (NEEK).
This file is distributed in the hope that it will be useful, but WITHOUT
WARRANTY OF ANY KIND.
Author(s): Ole Saether
DESCRIPTION:
This example should be used together with ex2a-tx433.asm. One nRF9E5
evaluation board (receiver) should be programmed with the hex-file generated
from assembling this file and the other evaluation board (transmitter)
programmed with the hex-file generated from assembling ex2a-tx433.asm.
All switches on the DIP-swith S206 on the receiver must be set to the "on"
position and all switches on the DIP-swith S205 on the transmitter must be
set to the "on" position.
When one of the switched SW1-SW4 on the transmitter is pressed the
corresponding LED on the receiver is turned on.
The functionality is the same as in ex2c-rx.c.
它是SourceForge上的一個開源項目，使用Malib實現實時處理，CSU Face Identification evaluation System進行人臉識別。算法包括：主成份分析(principle components analysis (PCA)),a.k.a eigenfaces算法,混合主成份分析,線性判別分析(PCA+LDA),圖像差分分類器(IIDC),彈性圖像匹配算法(EBGM)等等
Malic is realtime face recognition system that based on Malib and CSU Face Identification evaluation System (csuFaceIdEval). Uses Malib library for realtime image processing and some of csuFaceIdEval for face recognition.
The goal of this thesis is the development of traffic engineering rules for cellular packet
radio networks based on GPRS and EDGE. They are based on traffic models for typical
mobile applications. Load generators, representing these traffic models, are developed
and integrated into a simulation environment with the prototypical implementation of
the EGPRS protocols and models for the radio channel, which were also developed in
the framework of this thesis. With this simulation tool a comprehensive performance
evaluation is carried out that leads to the traffic engineering rules.
These codes require an ASCII input file interp.dat of the following form:
N: Number of Polynomial Interpolation Points (Small)
First Sample (x1,y1)
Second Sample (x2,y2)
...
Nth Sample (xN,yN)
N1: Number of Error evaluation Points (Large)
First Sample (x1,y1)
Second Sample (x2,y2)
...
N1th Sample (xN1,yN1)
A large body of computer-aided techniques has been developed in recent years to assist
in the process of modeling, analyzing, and designing communication systems . These
computer-aided techniques fall into two categories: formula-based approaches, where the
computer is used to evaluate complex formulas, and simulation-based approaches, where the
computer is used to simulate the waveforms or signals that flow through the system. The
second approach, which involves “waveform”-level simulation (and often incorporates
analytical techniques), is the subject of this book.
Since performance evaluation and trade off studies are the central issues in the analysis
and design of communication systems, we will focus on the use of simulation for evaluating
the performance of analog and digital communication systems with the emphasis on digitalcommunication systems.
