針對盤山路存在的轉彎盲區，即在轉彎時司機無法得知彎路對面是否有車輛通過，設計一種基于C8051F310的山路轉彎預防警示系統。該系統利用一階濾波算法檢測山路轉彎時是否有車輛通過。運用該算法可增強系統檢測的實時性，提高檢測機動車輛的靈敏度，同時大大減少環境溫度對檢測的干擾。試驗表明該系統能夠正確指示出在山路轉彎時是否有車輛通過，目前該系統已安裝在盤山路上，可大大減少事故的發生率。
Abstract:
Aiming at passing hilly road，there is a turn blind spot.Motormen usually do not know if the passing of vehicles pass the road.So a system of defending accident on hilly road is designed,which is based on MCU C8051F310.The sys-tem uses the first-order filter algorithm to detect whether there are passing vehicles.This algorithm enhances the real-time detection and improves the sensitivity of detection vehicles.Meanwhile,it reduces the detection interference of environmen-tal temperature.The experimental results show that this system can exactly indicate if there are passing vehicles.At present,the system has been successfully applied to hilly road.The system can greatly decrease accident.
為了解決磁放大器性能測試過程中，需要對其供給不同數值恒定電流的問題，設計了一種基于DAC7512和單片機的數控恒流源系統。該系統采用AT89C51作為主控器件，將計算機發送的電流控制字命令轉換為D/A轉換器控制字，通過模擬SPI通信接口，寫D/A控制字到DAC7512，從而控制其輸出相應數字電壓值，經差動縮放電路、電壓/電路變換電路和功率驅動電路，最后輸出恒定電流。實驗結果表明，恒流源輸出電流調節范圍為-45~+45 mA、精度為±0.1 mA，分辨率達0.024 4 mA，具有應用靈活，外圍電路簡單，可靠性高的特點。該數控直流恒流源也可為相關產品的測試系統研發提供參考。
Abstract:
In order to solve the need to supply different values constant current for the magnetic amplifier in testing process， numerical control constant current source system was designed based on DAC7512 chip and microcontroller technology. The system used the AT89C51 as the main chip， which can convert the current control word from computer into to D/A control words. And the system wrote D/A control word into the DAC7512 chip to control the output voltage value by the SPI communication interface， which can output corresponding constant current figures by scaling circuit， the V/I converter and power drive circuit. experimental results show that the current source output current adjustment range is -45~+45mA， accuracy is ± 0.1mA， and resolution ratio is 0.024 4mA
為了在工業生產及過程控制中準確測量溫度，設計了一種基于低功耗MSP430單片機的數字溫度計。整個系統通過單片機MSP430F1121A控制DS18B20讀取溫度，采用數碼管顯示，溫度傳感器DS18B20與單片機之間通過串口進行數據傳輸。MSP430系列單片機具有超低功耗，且外圍的整合性高，DS18B20只需一個端口即可實現數據通信，連接方便。通過多次實驗證明，該系統的測試結果與實際環境溫度一致，除了具有接口電路簡單、測量精度高、誤差小、可靠性高等特點外，其低成本、低功耗的特點使其擁有更廣闊的應用前景。
Abstract:
In order to obtain accurate measuring temperature in industrial production and process control， a digital thermometer based on MSP430 MCU is designed. The system uses MSP430F1121A MCU to control DS18B20， and gets the temperature data， which is displayed on the LED. The temperature sensor DS18B20 and MCU transmit data through serial communication. MSP430 series has ultra-low power and high integration， DS18B20 only needs one port to achieve data communication. Through many experimental results prove， this system is consistent with actual environment temperature. The system has characteristics of interface circuit simple， high measuring accuracy， minor error， high reliability， besides， the characteristics of low cost and low power make it having vaster application prospect.
為了擴大監控范圍，提高資源利用率，降低系統成本，提出了一種多通道視頻切換的解決方案。首先從視頻信號分離出行場信號，然后根據行場信號由DSP和FPGA產生控制信號，控制多路視頻通道之間的切換，從而實現讓一個視頻處理器同時監控不同場景。實驗結果表明，該方案可以在視頻監控告警系統中穩定、可靠地實現視頻通道的切換。
Abstract:
To expand the scope of monitoring， improve resource utilization， reduce system cost， a multiple video channels signal switching method is pointed out in this paper. First， horizontal sync signal and field sync signal from the video signal are separated， then control signal according to the sync signal by DSP and FPGA is generated to control the switching between multiple video channels. Thus， it achieves to make a video processor to monitor different place. experimental results show that the method can realize video channel switching reliably， and is applied in the video monitoring warning system successfully.
為提升虛擬儀器傳輸速率與實時性能，擴展監測范圍，在VC的軟件平臺上設計了一種全功能虛擬示波器。與傳統虛擬示波器相比，該系統采用嵌入式系統完成信號采集，采用工業以太網為傳輸介質，通過線性插值算法和多線程編程思想，實現波形顯示、參數計算、頻譜分析以及波形存儲及回放功能。實驗結果表明，該虛擬示波器可以實現20 kHz采樣頻率下的波形精確顯示，達到預期的各項指標。
Abstract:
o enhance the transfer rate and real-time of virtual instrument performance， expand scope of monitoring， this paper uses the VCs software platform to design a fully functional virtual oscilloscope. Compared with traditional virtual oscilloscope， this system adopts the embedded system to complete the data acquisition， industrial Ethernet as the transmission medium used by the linear interpolation algorithm and multi-threaded programming ideas， namely to achieve waveform display， parameter calculation， spectrum analysis and waveform storage and playback. experimental results show that the virtual oscilloscope can accurately display the waveform with 20kHz sampling frequency， and achieve the desired targets.
FFmpeg is an audio/video conversion tool. It includes libavcodec, the leading open source codec library. An experimental streaming server for live broadcasts is also included
Antinat is a flexible SOCKS server and client library for writing proxy-based applications. It supports SOCKS 4, SOCKS 5, authentication, CHAP, XML firewalling, Win32, server chaining, and UDP. It also contains very experimental IPv6 support
With OpenSSL 0.9.6, a new component has been added to support external crypto devices, for example accelerator cards. The component is called ENGINE, and has still a pretty experimental status and almost no documentation. It s designed to be fairly easily extensible by the calling programs.
The Engineering Vibration Toolbox is a set of educational programs
written in Octave by Joseph C. Slater. Also included are a number of help files,
demonstration examples, and data files containing raw experimental data. The
codes include single degree of freedom response, response spectrum, finite
elements, numerical integration, and phase plane analysis.
