embed visual v++串口調試助手
上傳時間： 2013-12-06
上傳用戶：zhuimenghuadie
v h d l 編程，通過蜂鳴器播放定制的樂曲，
標簽： 編程
上傳時間： 2014-07-22
上傳用戶：dongbaobao
gnumake manual v 3.80 中文版 和 英文版
上傳時間： 2016-09-29
上傳用戶：zhenyushaw
用單片機和ad0809做成的數字電壓表０～５v有原理圖，簡潔易懂
標簽： 0809 ad 用單片機 數字電壓表
上傳時間： 2013-12-13
上傳用戶：dapangxie
S-35390A是可以在超低消耗電流、寬工作電壓范圍內工作的2線CMOS實時時鐘IC。工作電 壓為1.3 ~ 5.5 V、可適用于從主電源電壓到備用電池電壓的寬幅電源電壓。通過0.25 μA的計 時消耗電流和寬范圍的計時電源電壓，可大幅度地改善電池的持續時間。在使用備用電池工 作的系統中，內置的自由寄存器可作為用戶備用存儲器來使用。在主電源切斷前存儲在寄存 器中的信息，可在電壓恢復后的任何時候讀出。 本產品因為內置了時鐘校正功能，所以可以在很寬的范圍內校正因振蕩電路的頻率偏差所導 致的時鐘數據的提前或滯后。通過此功能和溫度傳感器的結合，可根據溫度變化來對時鐘進 行校正，從而實現不受環境溫度影響的高精度的計時功能
上傳時間： 2016-10-16
上傳用戶：壞壞的華仔
// -*- Mode: Verilog -*- // Filename : wb_master.v // Description : Wishbone Master Behavorial // Author : Winefred Washington // Created On : 2002 12 24 // Last Modified By: . // Last Modified On: . // Update Count : 0 // Status : Unknown, Use with caution! // Description Specification // General Description: 8, 16, 32-bit WISHBONE Master // Supported cycles: MASTER, READ/WRITE // MASTER, BLOCK READ/WRITE // MASTER, RMW // Data port, size: 8, 16, 32-bit // Data port, granularity 8-bit // Data port, Max. operand size 32-bit // Data transfer ordering: little endian // Data transfer sequencing: undefined
標簽： Description Behavorial wb_master Filename
上傳時間： 2014-07-11
上傳用戶：zhanditian
This diskette (version 1.0) contains demonstration programs and source codes in MATLAB (v.5.2) for algorithms listed in the textbook Global Positioning Systems, Inertial Navigation, and Integration, by M. S. Grewal, Lawrence Weill, and A. P. Andrews, published by John Wiley and Sons, 2000. Contents: MATLAB (Version 5.2) Demonstrations & Scripts Chapter4 ephemeris.m calculates the GPS satellite position in ECEF coordinates from its ephemeris parameters. Chapter5 Klobuchar_fix.m calculates the ionospheric delay. Chapter6 (shows the quaternion utilities)
標簽： demonstration diskette contains programs
上傳時間： 2016-10-20
上傳用戶：壞天使kk
個人所得稅計算器 v個人所得稅計算器
標簽： 計算器
上傳時間： 2014-01-23
上傳用戶：bibirnovis
Top module name : SHIFTER (File name : SHIFTER.v) 2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT. 3. Output pins: OUT [15:0]. 4. Input signals generated from test pattern are latched in one cycle and are synchronized at clock rising edge. 5. The SHIFT signal describes the shift number. The shift range is 0 to 15. 6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it shifts input data to left. 7. When the signal SIGN is high, the input data is a signed number and it shifts with sign extension. However, the input data is an unsigned number if the signal SIGN is low. 8. You can only use following gates in Table I and need to include the delay information (Tplh, Tphl) in your design.
上傳時間： 2013-12-13
上傳用戶：himbly
Top module name : SHIFTER (File name : SHIFTER.v) 2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT. 3. Output pins: OUT [15:0]. 4. Input signals generated from test pattern are latched in one cycle and are synchronized at clock rising edge. 5. The SHIFT signal describes the shift number. The shift range is 0 to 15. 6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it shifts input data to left. 7. When the signal SIGN is high, the input data is a signed number and it shifts with sign extension. However, the input data is an unsigned number if the signal SIGN is low. 8. You can only use following gates in Table I and need to include the delay information (Tplh, Tphl) in your design.
上傳時間： 2014-01-20
上傳用戶：三人用菜
