FEATURES400 MSPS internal clock speedIntegrated 10-bit DAC32-bit tuning wordPhase noise ≤ –120 dBc/Hz @ 1 kHz offset (DAC output)Excellent dynamic performance>75 dB SFDR @ 160 MHz (±100 kHz offset) AOUTSerial I/O control1.8 V power supplySoftware and hardware controlled power-down48-lead TQFP/EP packageSupport for 5 V input levels on most digital inputsPLL REFCLK multiplier (4× to 20×)Internal oscillator; can be driven by a single crystalPhase modulation capabilityMultichip synchronization
The PCA9534 is a 16-pin CMOS device that provide 8 bits of General Purpose parallel
Input/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed to
enhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvements
include higher drive capability, 5 V I/O tolerance, lower supply current, individual I/O
configuration, 400 kHz clock frequency, and smaller packaging. I/O expanders provide a
simple solution when additional I/O is needed for ACPI power switches, sensors,
push buttons, LEDs, fans, etc.
This application report discusses the design of non-invasive optical plethysmographyalso called as pulsoximeter using the MSP430FG437 Microcontroller (MCU). Thepulsoximeter consists of a peripheral probe combined with the MCU displaying theoxygen saturation and pulse rate on a LCD glass. The same sensor is used for bothheart-rate detection and pulsoximetering in this application. The probe is placed on aperipheral point of the body such as a finger tip, ear lobe or the nose. The probeincludes two light emitting diodes (LEDs), one in the visible red spectrum (660nm) andthe other in the infrared spectrum (940nm). The percentage of oxygen in the body isworked by measuring the intensity from each frequency of light after it transmitsthrough the body and then calculating the ratio between these two intensities.
用戶程序示例教程
The Blinky project is a simple program for the LPC2138using Keil MCB2130 Microcontroller Board.
It blinks the LEDs at speed according to the Potentiometer setting and prints the current seting to the Serial Port 1.In addition it generates a sine wave with an adjustable frequency on the speaker of the board.
The XL6003 regulator is fixed frequency PWM Boost (step-up) DC/DC converter, capable ofdriving 1050mA load current with excellent line and load regulation. The regulator is simple to use because it includes internal frequency compensation and a fixed-frequency oscillator so that it requires a minimum number of external components to work. The XL6003 could directly drive 5~10 3W LED units at VIN=12V.
The PCA9534 is a 16-pin CMOS device that provide 8 bits of General Purpose parallel
Input/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed to
enhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvements
include higher drive capability, 5 V I/O tolerance, lower supply current, individual I/O
configuration, 400 kHz clock frequency, and smaller packaging. I/O expanders provide a
simple solution when additional I/O is needed for ACPI power switches, sensors,
push buttons, LEDs, fans, etc.
PCA9511, PCA9512, PCA9513, PCA9514, PCA9515, PCA9516, PCA9518,P82B96, P82B715Abstract - Philips Semiconductors family of Repeaters, Hubs and Expanders are detailed in this application notethat discusses device operation, maximum cable length and frequency calculations and typical applications.
基于變頻調速的水平連鑄機拉坯輥速度控制系統Frequency Inverter Based Drawing RollerS peedC ontrolSy stem ofHorizontal Continuous Casting MachineA 偉劉沖旅巴(南 華 大 學電氣工程學院，衡陽421001)摘要拉坯輥速度控制是水平連鑄工藝的關鍵技術之一，采用變頻器實現水平連鑄機拉坯輥速度程序控制，由信號發生裝置給變頻器提供程控信號。現場應用表明該控制系統速度響應快，控制精度高，滿足了水平連鑄生產的需要。關鍵詞水平連鑄拉坯輥速度程序控制變頻器Absh'act Speedc ontorlof dr awingor leris on eo fth ek eyte chnologiesfo rho rizontalco ntinuousca stingm achine.Fo rth ispu rpose,fr equencyco nverterisad optedfo rdr awingor lersp eedp rogrammablec ontorlof ho rizontalco ntinuousca stingm achine,th ep rogrammableco ntorlsi gnalto fr equencyc onverteris provided場a signal generator. The results of application show that the response of system is rapid and the control accuracy is high enough to meet thedemand of production of horizontal continuous casting.Keywords Horizontalco ntinuousc asting Drawingor ler Speedp rogrammablec ontrol Ferquencyin verter
隨著 現 代 化工業生產對鋼材需求量的日益增加，連鑄生產能力已經成為衡量一個國家冶金工業發展水平的重要指標之一。近十幾年來，水平連鑄由于具有投資少、鑄坯直、見效快等多方面的優點，國內許多鋼鐵企業利用水平連鑄機來澆鑄特種合金鋼，發揮了其獨特的優勢并取得了較好的經濟效益〔1,2)0采用 水 平 連鑄機澆鑄特種合金鋼時，由于拉坯機是水平連鑄系統中的關鍵設備之一，拉坯機及其控制性能的好壞直接影響著連鑄坯的質量，因此，連鑄的拉坯技術便成為整個水平連鑄技術的核心。由于鋼的冶煉過程是在高溫下進行的，鋼水溫度的變化又容易影響鑄坯的質量和成材率，因此，如何能在高溫環境下控制好與鑄坯速度相關的參數(拉、推程量，中停時間和拉坯頻率等)對于確保連鑄作業的進一步高效化，延長系統的連續作業時間十分關鍵。因此，拉坯輥速度控制技術是連鑄生產過程控制領域中的關鍵技術之- [31
