PW2330 develops a high efficiency synchronous step down DC-DC converter capable of delivering3A output current. PW2330 operates over a wide input voltage range from 4.5V to 30V andintegrates main switch and synchronous switch with very low RDS(ON) to minimize the conductionloss. PW2330 adopts the proprietary instant PWM architecture to achieve fast transient responsesfor high step down applications and high efficiency at light loads. In addition, it operates atpseudo-constant frequency of 500kHz under continuous conduction mode to minimize the size ofinductor and capacitor
The PW2312 is a high frequency, synchronous, rectified, step-down, switch-mode converter withinternal power MOSFETs. It offers a very compact solution to achieve a 1.5A peak output currentover a wide input supply range, with excellent load and line regulation.The PW2312 requires a minimal number of readily available, external components and is available ina space saving SOT23-6 package.
The PW2228A is a high efficiency single inductor Buck-Boost converter which can supply theload current up to 1.5A. It provides auto-transition between Buck and Boost Mode. The PW2228Aoperates at 2.4MHz switching frequency in CCM. DC/DC converter operates at Pulse-Skipping Modeat light load. The output voltage is programmable using an external resistor divider, or is fixed to3.3V internally. The load is disconnected from the VIN during shutdown.The PW2228A is available in TDFN3X3-10 package.
PW2205 develops a high efficiency synchronous step-down DC-DC converter capable of delivering5A output current. PW2205 operates over a wide input voltage range from 4.5V to 30V andintegrates main switch and synchronous switch with very low RDS(ON) to minimize the conductionloss.PW2205 adopts the instant PWM architecture to achieve fast transient responses for high step downapplications and high efficiency at light loads. In addition, it operates at pseudo-constant frequencyof 500kHz under continuous conduction mode to minimize the size of inductor and capacitor
The PW2163D is a high frequency, synchronous, rectified, step-down, switch-mode converter withinternal powerMOSFETs. It offers a very compact solution to provide a 3A continuous current over awide input supply range,with excellent load and line regulation.The PW2163D requires a minimal number of readily available, external components and is availablein a spacesaving SOT23-6 package
The PW2163 is a high efficiency 500 kHz synchronous step-down DC-DC converter capable ofdelivering 3A current. The PW2163 operates over a wide input voltage range from 4.5V to 18V andintegrates main switch and synchronous switch with very low RDS(ON) to minimize the conductionloss. Low output voltage ripple and small external inductor and capacitor sizes are achieved with 500kHz switching frequency. It adopts the instant PWM architecture to achieve fast transient responsesfor high step down applications
The PW2053 is a high-efficiency monolithic synchronous buck regulator using a constantfrequency, current mode architecture. The device is available in an adjustable version. Supply currentwith no load is 40uA and drops to <1uA in shutdown. The 2.5V to 5.5V input voltage range makesthe PW2053 ideally suited for single Li-Ion battery powered applications. 100% duty cycle provideslow dropout operation, extending battery life in portable systems. PWM/PFM mode operationprovides very low output ripple voltage for noise sensitive applications. Switching frequency isinternally set at 1.2MHz, allowing the use of small surface mount inductors and capacitors. Lowoutput voltages are easily supported with the 0.6V feedback reference voltage
本系統采用電動機電樞供電回路串接采樣電阻的方式來實現對小型直流有刷電動機的轉速測量。該系統主要由二階低通濾波電路,小信號放大電路、單片機測量顯示電路、開關穩壓電源電路等組成。同時自制電機測速裝置,用高頻磁環作為載體,用線圈繞制磁環,利用電磁感應原理檢測電機運行時的漏磁,將變化的磁場信號轉化為磁環上的感應電流。用信號處理單元電路將微弱電信號轉化為脈沖信號,送由單片機檢測,從而達到準確測量電機的速度的要求。In this system, the sampling resistance of armature power supply circuit is connected in series to measure the speed of small DC brush motor. The system is mainly composed of second-order low-pass filter circuit, small signal amplifier circuit, single-chip measurement and display circuit, switching regulated power supply circuit and so on. At the same time, the self-made motor speed measuring device uses high frequency magnetic ring as the carrier, coil winding magnetic ring, and electromagnetic induction principle to detect the leakage of magnetic field during the operation of the motor, which converts the changed magnetic field signal into the induced current on the magnetic ring. The weak electric signal is transformed into pulse signal by signal processing unit circuit, which is sent to single chip computer for detection, so as to meet the requirement of accurate measurement of motor speed.
本系統基于STM32單片機設計的非接觸式電流檢測控制系統,通過OPA548片將所給任意信號放大,由100Ω電阻和INA128芯片進行電流電壓轉換放大后,利用STM32單片機對獲取的電壓信號以0.488μs頻率采樣,利用STM32單片機的FFT庫,獲得信號的諧波信息。測量電流信號精準,該設計可廣泛應用在以STM32單片機為核心控制器件的新型儀表中,性能精準且抗干擾能力強。This system is a non-contact current detection and control system based on STM32 single chip microcomputer. It amplifiesany signal through OPA548 chip, converts and amplifies the current and voltage by 100 Ω resistance and INA128 chip. The obtainedvoltage signal is sampled at the frequency of 0.488 μs by STM 32 single chip microcomputer, and the harmonic information of the signalis obtained by the FFT library of STM 32 single chip microcomputer. The measurement of current signal is accurate. This design can bewidely used in a new instrument with STM 32 single chip microcomputer as its core control device, with accurate performance and stronganti-interference capability.
