The MAX17600–MAX17605 devices are high-speedMOSFET drivers capable of sinking /sourcing 4A peakcurrents. The devices have various inverting and noninvertingpart options that provide greater flexibility incontrolling the MOSFET. The devices have internal logiccircuitry that prevents shoot-through during output-statchanges. The logic inputs are protected against voltagespikes up to +14V, regardless of VDD voltage. Propagationdelay time is minimized and matched between the dualchannels. The devices have very fast switching time,combined with short propagation delays (12ns typ),making them ideal for high-frequency circuits. Thedevices operate from a +4V to +14V single powersupply and typically consume 1mA of supply current.The MAX17600/MAX17601 have standard TTLinput logic levels, while the MAX17603 /MAX17604/MAX17605 have CMOS-like high-noise margin (HNM)input logic levels. The MAX17600/MAX17603 are dualinverting input drivers, the MAX17601/MAX17604 aredual noninverting input drivers, and the MAX17602 /MAX17605 devices have one noninverting and oneinverting input. These devices are provided with enablepins (ENA, ENB) for better control of driver operation.
標簽： 17600 MAX 數據資料
上傳時間： 2013-12-20
上傳用戶：zhangxin
The LT®6552 is a specialized dual-differencing 75MHzoperational amplifier ideal for rejecting common modenoise as a video line receiver. The input pairs are designedto operate with equal but opposite large-signal differencesand provide exceptional high frequency commonmode rejection (CMRR of 65dB at 10MHz), therebyforming an extremely versatile gain block structure thatminimizes component count in most situations. The dualinput pairs are free to take on independent common modelevels, while the two voltage differentials are summedinternally to form a net input signal.
上傳時間： 2014-12-23
上傳用戶：13691535575
Linear Technology’s High Frequency Product lineupincludes a variety of RF I/Q modulators. The purpose ofthis application note is to illustrate the circuits requiredto interface these modulators with several popular D/Aconverters. Such circuits typically are required to maximizethe voltage transfer from the DAC to the baseband inputsof the modulator, as well as provide some reconstructionfi ltering.
標簽： DA轉換 接口 射頻 調制
上傳時間： 2013-10-19
上傳用戶：FreeSky
ANALOG INPUT BANDWIDTH is a measure of the frequencyat which the reconstructed output fundamental drops3 dB below its low frequency value for a full scale input. Thetest is performed with fIN equal to 100 kHz plus integer multiplesof fCLK. The input frequency at which the output is −3dB relative to the low frequency input signal is the full powerbandwidth.APERTURE JITTER is the variation in aperture delay fromsample to sample. Aperture jitter shows up as input noise.APERTURE DELAY See Sampling Delay.BOTTOM OFFSET is the difference between the input voltagethat just causes the output code to transition to the firstcode and the negative reference voltage. Bottom Offset isdefined as EOB = VZT–VRB, where VZT is the first code transitioninput voltage and VRB is the lower reference voltage.Note that this is different from the normal Zero Scale Error.CONVERSION LATENCY See PIPELINE DELAY.CONVERSION TIME is the time required for a completemeasurement by an analog-to-digital converter. Since theConversion Time does not include acquisition time, multiplexerset up time, or other elements of a complete conversioncycle, the conversion time may be less than theThroughput Time.DC COMMON-MODE ERROR is a specification which appliesto ADCs with differential inputs. It is the change in theoutput code that occurs when the analog voltages on the twoinputs are changed by an equal amount. It is usually expressed in LSBs.
標簽： Converter Defi ADC 轉換器
上傳時間： 2013-11-12
上傳用戶：pans0ul
Abstract: This application note illustrates an intermediate 8V switching power supply for an automotive radio and infotainment system.The design withstands the complete automotive input voltage range (including cold crank and load dump conditions), assuring a stable8V supply for common subsystems such as a CD driver, LCDs, and a radio module in modern infotainment systems. To avoiddisturbance in the AM and FM bands, the switching power supply runs at a fixed frequency of 2MHz, enabling an ideal solution forradio systems.
標簽： 汽車無線電 信息娛樂系統 開關電源
上傳時間： 2013-11-20
上傳用戶：feitian920
Abstract: Impedance mismatches in a radio-frequency (RF) electrical transmission line cause power loss andreflected energy. Voltage standing wave ratio (VSWR) is a way to measure transmission line imperfections. Thistutorial defines VSWR and explains how it is calculated. Finally, an antenna VSWR monitoring system is shown.
標簽： VSWR 輸電線路 精確測量 電壓駐波比
上傳時間： 2013-10-19
上傳用戶：yuanwenjiao
高的工作電壓高達100V N雙N溝道MOSFET同步驅動 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
上傳時間： 2013-10-24
上傳用戶：wd450412225
Easy-to-use and compact point-of-load power suppliesare necessary in systems with widely distributed, highcurrent, low voltage loads. The LTC®3415 provides acompact, simple and versatile solution. It includes a pairof integrated complementary power MOSFETs (32mΩtop and 25mΩ bottom) and requires no external senseresistor. A complete design requires an inductor andinput/output capacitors, and that’s it. The result is a fast,constant frequency, 7A current mode DC/DC switchingregulator.
上傳時間： 2013-10-18
上傳用戶：avensy
Automotive batteries, industrial power supplies, distributedsupplies and wall transformers are all sources ofwide-ranging high voltage inputs. The easiest way to stepdown these sources is with a high voltage monolithicstep-down regulator that can directly accept a wide inputrange and produce a well-regulated output. The LT®3493accepts inputs from 3.6V to 36V and LT3481 acceptsinputs from 3.6V to 34V. Both provide excellent lineand load regulation and dynamic response. The LT3481offers a high effi ciency solution over a wide load range andkeeps the output ripple low during Burst Mode® operationwhile the LT3493 provides a tiny solution with minimalexternal components. The LT3493 operates at 750kHzand the LT3481 has adjustable frequency from 300kHzto 2.8MHz. High frequency operation enables the use ofsmall, low cost inductors and ceramic capacitors.
標簽： 寬 輸入 降壓型穩壓器
上傳時間： 2014-12-24
上傳用戶：Pzj
Telecommunication, satellite links and set-top boxes allrequire tuning a high frequency oscillator. The actualtuning element is a varactor diode, a 2-terminal device thatchanges capacitance as a function of reverse bias voltage.1 The oscillator is part of a frequency synthesizingloop, as detailed in Figure 1. A phase locked loop (PLL)compares a divided down representation of the oscillatorwith a frequency reference. The PLL’s output is levelshifted to provide the high voltage necessary to bias thevaractor, which closes a feedback loop by voltage tuningthe oscillator. This loop forces the voltage controlledoscillator (VCO) to operate at a frequency determined bythe frequency reference and the divider’s division ratio.
標簽： 開關穩壓器 低噪聲 上傳時間： 2013-12-20
上傳用戶：ABCDE
蟲蟲下載站版權所有 京ICP備2021023401號-1
