特點 精確度0.25%滿刻度 ±1位數 輸入配線系統可任意選擇 CT比可任意設定 具有異常電流值與異常次數記錄保留功能 電流過高或過低檢測可任意設定 報警繼電器復歸方式可任意設定 尺寸小,穩定性高 2.主要規格 輔助電源: AC110V&220V ±20%(50 or 60Hz) AC220V&440V ±20%(50 or 60Hz)(optional) 精確度: 0.25% F.S. ±1 digit 輸入負載: <0.2VA (Current) 最大過載能力 : Current related input: 2 x rated continuous 10 x rated 30 sec. 25 x rated 3sec. 50 x rated 1 sec. 輸入電流范圍: AC0-5A (10-1000Hz) CT ratio : 1-2000 adjustable 啟動延遲動作時間: 0-99.9 second adjustable 繼電器延遲動作時間: 0-99.9 second adjustable 繼電器復歸方式: Manual (N) / latch(L) can be modified 繼電器磁滯范圍: 0-999 digit adjustable 繼電器動作方向: HI /LO/GO/HL can be modified 繼電器容量: AC 250V-5A, DC 30V-7A 過載顯示: "doFL" 溫度系數: 50ppm/℃ (0-50℃) 顯示幕: Red high efficiency LEDs high 14.22mm(.56")(PV) Red high efficiency LEDs high 14.22mm(.276")(NO) 參數設定方式: Touch switches 記憶型式 : Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc(input/output 使用環境條件 : 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上傳時間： 2013-10-14
上傳用戶：wanghui2438
特點 最高輸入頻率 10KHz 計數速度 50/10000脈波/秒可選擇 四種輸入模式可選擇(加算,減算,加減算,90度相位差加減算) 90度相位差加減算具有提高解析度4倍功能 輸入脈波具有預設刻度功能 計數暫時停止功能 3組報警功能 15BIT類比輸出功能 數位RS-485界面 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脈波觸發電位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高輸入頻率: <10KHz (up,down,up/down mode) <3KHz (quadrature mode) 輸出動作時間 : 0.1 to 99.9 second adjustable 輸出復歸方式: Manual(N) or automatic (R or C) can be modif 繼電器容量: AC 250V-5A, DC 30V-7A 顯示值范圍: -199999 to 999999 類比輸出解析度: 15 bit DAC 輸出反應速度: < 1/f+10ms(0-90%) 輸出負載能力: < 10mA for voltage mode < 10V for current mode <[(V+)-7.5V]/20mA for two-wire mode 輸出之漣波: < 0.1% F.S. 通訊位址: "01"-"FF" 傳輸速度: 19200/9600/4800/2400 selective 通信協議: Modbus RTU mode 顯示幕: Red high efficiency LEDs high 14.22mm (.56") 參數設定方式: Touch switches 感應器電源: 12VDC +/-3%(<60mA) 記憶方式: Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上傳時間： 2013-11-23
上傳用戶：redmoons
特點 最高輸入頻率 10KHz 計數速度 50/10000脈波/秒可選擇 四種輸入模式可選擇(加算,減算,加減算,90度相位差加減算) 90度相位差加減算具有提高解析度4倍功能 輸入脈波具有預設刻度功能 前置量設定功能(二段設定)可選擇 數位化指撥設定操作簡易 計數暫時停止功能 3組報警功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脈波觸發電位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高輸入頻率: <10KHz (up,down,up/down mode) <5KHz (quadrature mode) 輸出動作時間 : 0.1 to 99.9 second adjustable 輸出復歸方式: Manual(N) or automatic (R or C) can be modif 繼電器容量: AC 250V-5A, DC 30V-7A 顯示值范圍: -199999 to 999999 顯示幕: Red high efficiency LEDs high 9.2mm (.36") 參數設定方式: Touch switches 感應器電源: 12VDC +/-3%(<60mA) ( 感應器電源 ) 記憶方式: Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上傳時間： 2013-11-12
上傳用戶：909000580
特點 精確度0.1%滿刻度 可輸入交直流電流/交直流電壓/電位計/傳送器...等信號 16 BIT類比輸出功能 輸入與輸出絕緣耐壓2仟伏特/1分鐘 寬范圍交直流兩用電源設計 尺寸小,穩定性高 2主要規格 精確度: 0.1% F.S. (23 ±5℃) 顯示值范圍: 0-±19999 digit adjustable 類比輸出解析度: 16 bit DAC 輸出反應速度: < 250 ms (0-90%)(>10Hz) 輸出負載能力: < 10mA for voltage mode < 10V for current mode 輸出之漣波: < 0.1% F.S. 歸零調整范圍: 0- ±9999 Digit adjustable 最大值調整范圍: 0- ±9999 Digit adjustable 溫度系數: 50ppm/℃ (0-50℃) 顯示幕: Red high efficiency LEDs high 10.16mm (0.4") 隔離特性: Input/Output/Power/Case 參數設定方式: Touch switches 記憶方式: Non-volatile E2PROM memory 絕緣抗阻: >100Mohm with 500V DC 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用環境條件: 0-60℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) 安裝方式: Socket/plugin type with barrier terminals CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上傳時間： 2014-01-05
上傳用戶：eastgan
特點 精確度0.1%滿刻度 ±1位數 顯示范圍-19999-99999可任意規劃 可直接量測直流電流/直流電壓,無需另接輔助電源 尺寸小(24x48x50mm),穩定性高 分離式端子,配線容易 CE 認證 2.主要規格 輔助電源: None 精確度: 0.1% F.S. ±1 digit(1-100%F.S.) 輸入抗阻 : >100Mohm(<2V range) >2Mohm(<2Vrange) < 0.25VA(current ranges) < 1000Vrms(>54V ranges) 最大過載能力: < 150Vrms(<54V ranges)
上傳時間： 2013-10-08
上傳用戶：tiantwo
無刷電機 霍爾傳感器 反電動勢 控制 原理：無刷直流（Brushless Direct Current， BLDC）電機是一種正快速普及的電機類型，它可在家用電器、汽車、航空航天、消費品、醫療、工業自動化設備和儀器等行業中使用。 正如名稱指出的那樣，BLDC 電機不用電刷來換向，而是使用電子換向。BLDC 電機和有刷直流電機以及感應電機相比，有許多優點。其中包括：
上傳時間： 2013-11-24
上傳用戶：miaochun888
The NCV7356 is a physical layer device for a single wire data linkcapable of operating with various Carrier Sense Multiple Accesswith Collision Resolution (CSMA/CR) protocols such as the BoschController Area Network (CAN) version 2.0. This serial data linknetwork is intended for use in applications where high data rate is notrequired and a lower data rate can achieve cost reductions in both thephysical media components and in the microprocessor and/ordedicated logic devices which use the network.The network shall be able to operate in either the normal data ratemode or a high-speed data download mode for assembly line andservice data transfer operations. The high-speed mode is onlyintended to be operational when the bus is attached to an off-boardservice node. This node shall provide temporary bus electrical loadswhich facilitate higher speed operation. Such temporary loads shouldbe removed when not performing download operations.The bit rate for normal communications is typically 33 kbit/s, forhigh-speed transmissions like described above a typical bit rate of83 kbit/s is recommended. The NCV7356 features undervoltagelockout, timeout for faulty blocked input signals, output blankingtime in case of bus ringing and a very low sleep mode current.
上傳時間： 2013-10-24
上傳用戶：s藍莓汁
Abstract: This application note helps system designers choose the correct external components for use with the MAX16948 dualremote antenna LDO/switch, thus ensuring that automobile-regulated phantom antenna supply and output-current-monitoring circuitrymeet performance objectives. An electronic calculator is provided that helps specify the critical external components for theMAX16948, thus reducing design time. The calculator also determines the device's analog output voltage, output current-limitthreshold, and output current-sensing accuracies. The calculator includes new automatic Step By Step feature that assists designerswith component choice. To use the new automatic feature, click on the Step By Step button relative to the desired section.
上傳時間： 2013-11-04
上傳用戶：lhll918
闡述了軌道交通列車定位技術。介紹了在軌道交通系統中列車定位技術的功能，國內外軌道交通中主要采用的列車定位方法，重點論述了幾種主要定位技術，并從定位精度、閉塞制式、維護投資成本、抗干擾等方面進行分析比較。提出目前軌道交通定位技術應綜合運用，取長補短，多種方法相互融合，才能滿足軌道交通中對安全可靠性的要求。 Abstract: Rail train positioning technology is described. The paper introduces the funetions of the train positioning technology in the rail transit system， the main methods of train positioning do mestic and international rail， and focuses on several key methods， analyzes and compares from the positioning accuracy， block system, maintenance and investment cost， interference and so on， suggested that the current rail positioning technology should be integrated use of positioning method of meriging， learn from each other， to meet the reliability requirements of rail safety.
上傳時間： 2013-11-25
上傳用戶：franktu
本軟件是關于MAX338, MAX339的英文數據手冊：MAX338, MAX339 8通道/雙4通道、低泄漏、CMOS模擬多路復用器 The MAX338/MAX339 are monolithic, CMOS analog multiplexers (muxes). The 8-channel MAX338 is designed to connect one of eight inputs to a common output by control of a 3-bit binary address. The dual, 4-channel MAX339 is designed to connect one of four inputs to a common output by control of a 2-bit binary address. Both devices can be used as either a mux or a demux. On-resistance is 400Ω max, and the devices conduct current equally well in both directions. These muxes feature extremely low off leakages (less than 20pA at +25°C), and extremely low on-channel leakages (less than 50pA at +25°C). The new design offers guaranteed low charge injection (1.5pC typ) and electrostatic discharge (ESD) protection greater than 2000V, per method 3015.7. These improved muxes are pin-compatible upgrades for the industry-standard DG508A and DG509A. For similar Maxim devices with lower leakage and charge injection but higher on-resistance, see the MAX328 and MAX329.
上傳時間： 2013-11-12
上傳用戶：18711024007
<rt id="i4q4q"></rt>