以89S52單片機和EP1C6Q240C8型FPGA為控制核心的多功能計數器，是由峰值檢波、A/D轉換、程控放大、比較整形、移相網絡部分組成,可實現測量正弦信號的頻率、周期和相位差的功能。多功能計數器采用等精度的測量方法，可實現頻率為1Hz～10MHz、幅度為0.01～5Vrms的正弦信號的精確測頻，以及頻率為10Hz～100kHz、幅度為0.5～5Vrms的正弦信號精確測相。液晶顯示器能夠?qū)崟r顯示當前信號的頻率、周期和相位差。該多功能計數器精度高，界面友好，實用性強。 Abstract: A multi-function counter，which uses89S52MCU and EP1C6Q240C8FPGA as a control core，consists of peak detector，A/D conversion，program-controlled amplification，compared shaping and phase-shifting network part.The counter measures the frequency，period and phase of sinusoidal signal.With the equal precision method,the multi-function counter achieves the precise frequency measurement of the sinusoidal signal which its frequency is from1Hz to10MHz，its amplitude is from0.01Vrms to5Vrms，as well as the accurate phase measurement of the sinusoidal signal which its frequency is from10Hz to100kHz，its amplitude is from0.5Vrms to5Vrms.The LCD monitor real-time displays the frequency，period and phase difference of current signal.The multi-function counter features high precision，friendly interface，and strong practical.
標簽： FPGA 單片機 多功能 計數器
上傳時間： 2013-11-15
上傳用戶：gy592333
介紹基于VHDL的微型打印機控制器的設計。論述了微型打印機的基本原理，以及實現控制器的VHDL語言設計。打印機的數據來自系統中的存儲模塊，根據需要控制打印。該微型打印機控制器可取代傳統的微型打印機,且抗干擾性好,可靠性高，具有較強的移植性，稍加改動就可應用于不同場合。 Abstract: This paper introduced the design method of micro printer controller based on VHDL.The basic principles of microprinter is explained,as well as the realization of the controller by VHDL language.The printer data is from the system memory modules,can control printer.The design of microprinter controller has antigood and high reliability，it can replace the traditional printer.The controller has very good portability,and need little modify that can use in different situation.
標簽： VHDL 微型打印機 制器設計
上傳時間： 2013-11-03
上傳用戶：dudu1210004
介紹了一種TI公司最新推出的MSP430F247單片機，利用它自帶的I2C模塊驅動I2C總線的溫度傳感器TMP275。TMP275是一款具有高精度、低功耗的新型溫度傳感器。由于TMP275具有可編程功能，纖小的封裝以及極大的溫度范圍，因而廣泛應用于組建超小型溫度測量裝置。 Abstract: A new single chip microcomputer MSP430F247 which is released by TI is introduced.It can drive I2C interface digital temperature sensor TMP275 with I2C module.TMP275 is a new temperature sensor which has high accurate,low power. Because TMP275 has programmable function,small packages and wide temperature range,it is applied widely in very little temperature measurment equipment.
上傳時間： 2013-12-06
上傳用戶：asdfasdfd
介紹了一種基于C8051F020單片機的多路壓力測量儀。該測量儀選用電阻應變式壓力傳感器采集壓力信號，并經放大電路處理后送入C8051F020單片機，再由C8051F020單片機內部的A/D轉換器將采集到的壓力信號進行模數轉化，然后分別對數據進行存儲和顯示。該測量儀能測量6路壓力信號，并且各測量點都能單獨檢測和設置。由于采用了C8051F020單片機，簡化了硬件電路，增強了抗干擾能力，使得測量儀具有測量精度高，沖擊小等特點。 Abstract: A measurement apparatus for multi-channel pressure based on single chip microcomputer is introduced.It can measure 6 channels signal of the pressure，and the pressure measure points can be detection and located individually.The pressure signal sampling is obtained by resistor stress-type pressure sensors，the digital signals of 6 channels are collected through amplifying and adjustment circuit of pressure signals and internal integrated A/D converter of MCU.Finally，and it realizes the function to store and display data separately.C8051F020 was used to made hardware circuit simple，and it also enhanced the anti-interference ability.It features high precision and little impact.
標簽： C8051F020 單片機 多路 壓力
上傳時間： 2013-11-16
上傳用戶：yare
在汽車發動機起動時，若發動機起動后起動機不能及時斷電，將會燒毀起動機或損壞飛輪齒環；若變速器不在空檔位置起動，則起動機的瞬間動力將使汽車位移，還可能引起交通事故和人身安全。為此介紹一種利用NXP P89LPC901單片機控制的汽車起動保護控制器，通過檢測汽車起動開關、變速箱檔位、發動機轉速，實現對汽車發動機起動過程檢測和保護。起動保護控制器在發動機起動過程中通過采用逐個關閉打開負載系統，解決汽車發動機過程中因起動電流大而對汽車電源的沖擊影響,延長了電瓶壽命。 Abstract: When the automotive engine is started, the engine start motor and flywheel gear may be damaged， even traffic accidents and personal safeties may be caused by wrong operation or other factors.In order to ensure the automotive engine can be started normally and safely,it is necessary that the protecting measures and methods are considered in the automotive electrical control system.This paper introduces a kind of the automotive engine starting protect controller based on NXP P89LPC901 MCU.The controller can protect the engine starting process by detecting the starter key switch,transmission stall and engine speed.Through the use of close and open load system,the controller can solve the impact on automotive power because of the high-current load in the process of the automobile engine starting, and extend battery life.
上傳時間： 2013-10-15
上傳用戶：mikesering
Mega16是一款采用先進RISC精簡指令，內置A/D的8位單片機，可支持低電壓聯機 Flash和EEPROM 寫入功能；同時還支持 Basic和C 等高級語言編程。用它設計電子時鐘不僅成本低，硬件簡單，而且很容易實現系統移植。介紹了如何利用AVR系列單片機Mega16及1602字符液晶來設計電子時鐘的方法，同時給出了相應的電路原理及部分語言程序。 Abstract: ?Mega16 is a high-performance, low power consumption, the use of advanced RISC concise instructions, built-in A/D 8-bit microcontrollers, the on-line support for low-voltage Flash, EEPROM write function. Except Mega16 also support the Basic, C, and other high-level language programming.The electronic clock which is deisgned by Mega16 is not only low-cost, simple hardware, but easy to achieve system migration.The design method of electrioic clock based on the AVR Mega16 and character LCD1602 is introduced in this paper,and the corresponding circuit electrionic and some language program are given.
上傳時間： 2014-12-27
上傳用戶：zl5712176
介紹了一種基于AT89S52微處理器、鍵控顯示模式、多漢字顯示的顯示模塊設計方法。對AT89S52的內部功能及使用高128字節RAM時的尋址方式進行說明。給出了四漢字顯示模塊的硬件電路原理圖、主程序流程圖以及中斷顯示流程圖。 Abstract: The design method of display module base on the AT89S52 microcontroller,display mode controlled by keyboard and? showing several Chinese characterses are introduced in the paper.The internal function and the addressing mode for the high 128B RAM of the AT89S52 are explained.The basic circuit diagram,the main program flow chart and the display interrupt flow chart of four Chinese characterses display module are also given.
上傳時間： 2014-01-23
上傳用戶：咔樂塢
采用單片機AT89C2051實現溫度測量與控制,鍵盤和顯示電路實現溫度的設定、修改、清零以及當前溫度值的顯示,并對溫度超過上下限進行報警。闡述了該系統設計的硬件和軟件設計。 Abstract: The system of temperature measuring and controling is realized based on AT89C2051.The keyboard and display circuit is designed,which can be used for setting and modifying temperature value,resetting and displaying the present temperature value.At the same time the warning circuit is also designed in the system,which can deal with the alarm when temperature exceeds the upper limit and the lower limit.The hardware and software design of the system are explained．
上傳時間： 2013-11-18
上傳用戶：leehom61
為了解決磁放大器性能測試過程中，需要對其供給不同數值恒定電流的問題，設計了一種基于DAC7512和單片機的數控恒流源系統。該系統采用AT89C51作為主控器件，將計算機發送的電流控制字命令轉換為D/A轉換器控制字，通過模擬SPI通信接口，寫D/A控制字到DAC7512，從而控制其輸出相應數字電壓值，經差動縮放電路、電壓/電路變換電路和功率驅動電路，最后輸出恒定電流。實驗結果表明，恒流源輸出電流調節范圍為-45~+45 mA、精度為±0.1 mA，分辨率達0.024 4 mA，具有應用靈活，外圍電路簡單，可靠性高的特點。該數控直流恒流源也可為相關產品的測試系統研發提供參考。 Abstract: In order to solve the need to supply different values constant current for the magnetic amplifier in testing process， numerical control constant current source system was designed based on DAC7512 chip and microcontroller technology. The system used the AT89C51 as the main chip， which can convert the current control word from computer into to D/A control words. And the system wrote D/A control word into the DAC7512 chip to control the output voltage value by the SPI communication interface， which can output corresponding constant current figures by scaling circuit， the V/I converter and power drive circuit. Experimental results show that the current source output current adjustment range is -45~+45mA， accuracy is ± 0.1mA， and resolution ratio is 0.024 4mA
標簽： 7512 DAC 數控直流 恒流源
上傳時間： 2014-12-27
上傳用戶：invtnewer
針對51單片機系統中常用的A/D轉換器價格高、精度低的缺點，介紹TI公司的16 位的帶有I2C串行接口的A/D轉換器ADS1110的工作原理，給出ADS1110與AT89C51單片機系統的接口電路和軟件設計。實踐證明，ADS1110具有高性價比和實用性。 Abstract: According to the disadvantages of high expense and low accuracy of the general A/D converter used in MCS51 microchip system,the principle and working process of a high accuracy 16-bit A/D conversion ADS1110 which has I2C bus and belongs to TI Company are proposed here as well as the interface of ADS1110 to AT89C51 and software list.It is proved to be high performance index and practicability.
上傳時間： 2013-11-21
上傳用戶：gyq
蟲蟲下載站版權所有 京ICP備2021023401號-1
