Modern Compiler implementation in Java. Second Edition
標簽： implementation Compiler Edition Modern Second Java in
上傳時間： 2019-04-03
上傳用戶：zsx097
基于ARM_Linux與GPRS的GPS監控終端的研究與實現，這是一篇優秀碩士論文-GPS and GPRS-based ARM_Linux Research and implementation o
上傳時間： 2013-06-27
上傳用戶：lhw888
本文介紹了基于單片機AT89C51 的溫度控制系統的設計方案與軟硬件實現。采用溫度傳感器DS18B20 采集溫度數據，液晶顯示屏LCM1602 顯示溫度數據，AT24C02B 存儲溫度上下限設定
標簽： implementation Temperature SingleChip Control
上傳時間： 2013-06-03
上傳用戶：xoxoliguozhi
基于單片機的頻率計的實現和protuse仿真-Frequency meter based on single chip implementation and protuse simulation
上傳時間： 2013-06-04
上傳用戶：杜瑩12345
This application note is intended for system designers who require a hardware implementation overview of the development board features such as the power supply, the clock management, the reset control, the boot mode settings and the debug management. It shows how to use the High-density and Medium-density STM32F10xxx product families and describes the minimum hardware resources required to develop an STM32F10xxx application.
上傳時間： 2013-04-24
上傳用戶：epson850
VHDL source codes of the FPGA64, a fpga implementation of the C64 computer. Version for the c-one fpga board.
上傳時間： 2013-08-05
上傳用戶：wwwe
Abstract: Transimpedance amplifiers (TIAs) are widely used to translate the current output of sensors like photodiode-to-voltagesignals, since several circuits and instruments can only accept voltage input. An operational amplifier with a feedback resistor fromoutput to the inverting input is the most straightforward implementation of such a TIA. However, even this simple TIA circuit requirescareful trade-offs among noise gain, offset voltage, bandwidth, and stability. Clearly stability in a TIA is essential for good, reliableperformance. This application note explains the empirical calculations for assessing stability and then shows how to fine-tune theselection of the feedback phase-compensation capacitor.
標簽： Transimpedance Stabilize Amplifier Your
上傳時間： 2013-11-13
上傳用戶：daoyue
設計了水聲信號發生系統中的功率放大電路，可將前級電路產生的方波信號轉換為正弦信號，同時進行濾波、功率放大，使其滿足換能器對輸入信號的要求。該電路以單片機AT89C52，集成6階巴特沃思低通濾波芯片MF6以及大功率運算放大器LM12為核心，通過標準RS232接口與PC進行通信，實現信號增益的程控調節，對干擾信號具有良好的抑制作用。經調試該電路工作穩定正常，輸出波形無失真，在輸出功率以及放大增益、波紋系數等方面均滿足設計要求。 This paper presented a design and implementation of underwater acoustic power amplifer. This circuit converted the rectangle signal generated by frontend circuit into the sine signal， then filtered and power amplification， it meets the requirements of the transducer.Included AT89C52， 6th order Butterworth filter MF6， hipower amplififier LM12.Communication with PC through the RS232 port. The signal gain is adjustable and could be remote controlled. It has a good inhibitory effect on the interference signal. After debugged， this circuit works stable， the output waveform has no distortion， it meets the design requirement in outprt power， amplifier gain and ripple factor.
上傳時間： 2013-11-20
上傳用戶：qwe1234
One of the strengths of Synplify is the Finite State Machine compiler. This is a powerfulfeature that not only has the ability to automatically detect state machines in the sourcecode, and implement them with either sequential, gray, or one-hot encoding. But alsoperform a reachability analysis to determine all the states that could possibly bereached, and optimize away all states and transition logic that can not be reached.Thus, producing a highly optimal final implementation of the state machine.
標簽： Synplicity Machine Verilog Design
上傳時間： 2013-10-23
上傳用戶：司令部正軍級
Integrated EMI/Thermal Design forSwitching Power SuppliesWei ZhangThesis submitted to the Faculty of theVirginia Polytechnic Institute and State Universityin partial fulfillment of the requirements for the degree of Integrated EMI/Thermal Design forSwitching Power SuppliesWei Zhang(ABSTRACT)This work presents the modeling and analysis of EMI and thermal performancefor switch power supply by using the CAD tools. The methodology and design guidelinesare developed.By using a boost PFC circuit as an example, an equivalent circuit model is builtfor EMI noise prediction and analysis. The parasitic elements of circuit layout andcomponents are extracted analytically or by using CAD tools. Based on the model, circuitlayout and magnetic component design are modified to minimize circuit EMI. EMI filtercan be designed at an early stage without prototype implementation.In the second part, thermal analyses are conducted for the circuit by using thesoftware Flotherm, which includes the mechanism of conduction, convection andradiation. Thermal models are built for the components. Thermal performance of thecircuit and the temperature profile of components are predicted. Improved thermalmanagement and winding arrangement are investigated to reduce temperature.In the third part, several circuit layouts and inductor design examples are checkedfrom both the EMI and thermal point of view. Insightful information is obtained.
標簽： EMI 開關電源 英文
上傳時間： 2013-11-10
上傳用戶：1595690
蟲蟲下載站版權所有 京ICP備2021023401號-1
