便攜式信號采集在機器健康診斷系統中有較高的應用價值。機器健康診斷的信號特點是包括低頻信號。本文研究是為了實現簡易而且低成本的低頻便攜式信號采集。以Microchip公司單片機PIC18F1320為核心設計信號采集電路，實現了信號的采集和保存。系統采用串行電可擦除芯片24LC32A保存數據，經過有線通信，信號數據由串行口通過MAX232芯片輸送到微型計算機接收和保存，最后繪制出信號波形。 微型計算機程序采用Visual Basic編程。研究成功采樣頻率為3 kHz的復雜信號，證明該方案符合設計要求。
Abstract:
Portable signal acquisition is useful in machine health monitoring systems. The signal characteristics of machine health monitoring includes low frequency signals. The goal of this study is to realize simple, inexpensive and portable low frequency signal sampling. This paper provides the project of signal acquisition system design based on PIC18F1320 microcontroller manufactured by the Microchip Technology Incorporation to achieve signal sampling and storage. The system adopted EEPROM 24LC32A to store the signal data. The microcomputer received data via wired link with the MAX232 IC through the serial port. The microcomputer program, programmed in Visual Basic, received the data, stored it and plotted the signal. The study successfully samples 3kHz complicated signals and thus meets the design requirement.
介紹一種簡單射頻識別系統設計。該設計包括閱讀器、應答器和線圈3部分。由單片機控制閱讀器向應答器發射無線信號，并接收應答器回送的信號，再通過分析回送信號識別物品。閱讀器和應答器之間以半雙工通信方式通信。
Abstract:
A simple design of radio frequency identification system is given in this paper.The design includes reader,responder and winding.Through MCU，signals are sent to responder from reader，then corresponding signals are sent back. According to the analysis of the signals sent back，the objects can be identified.Half-duplex communication is adopted? between? reader? and? responder.
The MSP-FET430PIF is a Parallel Port interface (does not include target board) that is used to program and debug MSP430 FET tools and test boards through the JTAG interface. This interface is included in our FET tools, but sold without the development board. This interface uses a Parallel PC Port to communicate to the Debugger Software (IAR Kickstart software included) running on the PC. The interface uses the standard 14 pin header to communicate to the MSP430 device using the standard JTAG protocol.
The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is extremely low power, no external power supply is required. The tool has an integrated software environment and connects directly to the PC which greatly simplifies the set-up and use of the tool. The flash development tool supports development with all MSP430 flash parts.
Features
MSP430 debugging interface to connect a MSP430-Flash-device to a Parallel port on a PC
Supports JTAG debug protocol (NO support for Spy-Bi-Wire (2-wire JTAG) debug protocol, Spy-Bi-Wire (2-wire JTAG) is supported by MSP-FET430UIF)
Parallel Port cable and a 14-conductor target cable
Full documentation on CD ROM
Integrated IAR Kickstart user interface which includes:
Assembler
Linker
Limulator
Source-level debugger
Limited C-compiler
Technical specifications:
Backwardly compatable with existing FET tool boards.
The MSP-FET430U14 is a powerful flash emulation tool to quickly begin application development on the MSP430 MCU. It includes USB debugging interface used to program and debug the MSP430 in-system through the JTAG interface or the pin saving Spy Bi-Wire (2-wire JTAG) protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is ultra-low power, no external power supply is required.
The debugging tool interfaces the MSP430 to the included integrated software environment and includes code to start your design immediately. The MSP-FET430UIF development tools supports development with all MSP430 flash devices
AVR Studio 4.12 includes new device support and numerous overall enhancements;new breakpoint system, integrated AVR GCC development and improved docking system!See release notes for more details.
Atmel AVR 單片機上網方案
The AVR Embedded Internet Toolkit is the fastest way to connect anyembedded design to the Internet. It includes an ATmega AVR microcontroller,dedicated hardware, and all required software protocols forconnecting to the Internet. The AVR Embedded Internet Toolkit is thefastest choice for getting started with embedded Internet and for developinga complete embedded application connected to the Internet.
NXP Semiconductor designed the LPC2400 microcontrollers around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded Trace. The LPC2400 microcontrollers have 512 kB of on-chip high-speedFlash memory. This Flash memory includes a special 128-bit wide memory interface andaccelerator architecture that enables the CPU to execute sequential instructions fromFlash memory at the maximum 72 MHz system clock rate. This feature is available onlyon the LPC2000 ARM Microcontroller family of products. The LPC2400 can execute both32-bit ARM and 16-bit Thumb instructions. Support for the two Instruction Sets meansEngineers can choose to optimize their application for either performance or code size atthe sub-routine level. When the core executes instructions in Thumb state it can reducecode size by more than 30 % with only a small loss in performance while executinginstructions in ARM state maximizes core performance.
This application report discusses the design of non-invasive optical plethysmographyalso called as pulsoximeter using the MSP430FG437 Microcontroller (MCU). Thepulsoximeter consists of a peripheral probe combined with the MCU displaying theoxygen saturation and pulse rate on a LCD glass. The same sensor is used for bothheart-rate detection and pulsoximetering in this application. The probe is placed on aperipheral point of the body such as a finger tip, ear lobe or the nose. The probeincludes two light emitting diodes (LEDs), one in the visible red spectrum (660nm) andthe other in the infrared spectrum (940nm). The percentage of oxygen in the body isworked by measuring the intensity from each frequency of light after it transmitsthrough the body and then calculating the ratio between these two intensities.
The XL6003 regulator is fixed frequency PWM Boost (step-up) DC/DC converter, capable ofdriving 1050mA load current with excellent line and load regulation. The regulator is simple to use because it includes internal frequency compensation and a fixed-frequency oscillator so that it requires a minimum number of external components to work. The XL6003 could directly drive 5~10 3W LED units at VIN=12V.
The TRS232E is a dual driver/receiver that includes a capacitive voltage generator to supply TIA/RS-232-Fvoltage levels from a single 5-V supply. Each receiver converts TIA/RS-232-F inputs to 5-V TTL/CMOS levels.This receiver has a typical threshold of 1.3 V, a typical hysteresis of 0.5 V, and can accept ±30-V inputs. Eachdriver converts TTL/CMOS input levels into TIA/RS-232-F levels. The driver, receiver, and voltage-generatorfunctions are available as cells in the Texas Instruments LinASIC™ library.
