Boost LED drivers are often used to drive LEDs in series. If an LED fails while open,overvoltage protection (OVP) is necessary to avoid the damage to a boost integrated circuit (IC) or output capacitor. This application report presents the solutions to increase the TPS61043 LED driver OVP threshold.
The LTP5901 and LTP5902 require little external circuitry, as the devices references,decoupling and power supply filtering are integrated. The LTP5901 and LTP5902 will bemodularly certified for operation in the United States (FCC), Canada (IC) and theEuropean Union (CE).
Abstract: We can apply a BiCMOS integrated circuit with only resistors and no transistors to solve adifficult design problem. The mythically perfect operational amplifier's gain and temperature coefficient aredependent on external resistor values. Maxim precision resistor arrays are manufactured together on asingle die and then automatically trimmed, to ensure close ratio matching. This guarantees that theoperational amplifier (op amp) gain and temperature coefficient are predictable and reliable, even withlarge production volumes.
The LT®1943 is a highly integrated, 4-output regulatordesigned to power large TFT LCD panels. The LT1943employs switching regulators—instead of linear regulators—to minimize power dissipation and accommodate awide input voltage range. The wide input range, 4.5V to22V, allows it to accept a variety of power sources,including the commonly used 5V, 12V and 19V AC adaptors.
高的工作電壓高達100V N雙N溝道MOSFET同步驅動 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
Easy-to-use and compact point-of-load power suppliesare necessary in systems with widely distributed, highcurrent, low voltage loads. The LTC®3415 provides acompact, simple and versatile solution. It includes a pairof integrated complementary power MOSFETs (32mΩtop and 25mΩ bottom) and requires no external senseresistor. A complete design requires an inductor andinput/output capacitors, and that’s it. The result is a fast,constant frequency, 7A current mode DC/DC switchingregulator.
Industrial remote monitoring systems and keep-alivecircuits spend most of their time in standby mode. Manyof these systems also depend on battery power, so powersupply effi ciency in standby state is very important tomaximize battery life. The LT®8410/-1 high effi ciencyboost converter is ideal for these systems, requiringonly 8.5μA of quiescent current in standby mode. Thedevice integrates high value (12.4M/0.4M) output feedbackresistors, signifi cantly reducing input current whenthe output is in regulation with no load. Other featuresinclude an integrated 40V switch and Schottky diode,output disconnect with current limit, built in soft-start,overvoltage protection and a wide input range, all in atiny 8-pin 2mm × 2mm DFN package.
Linear Technology’s DC/DC step-down μModule®regulators are complete switchmode power supplies in asurface-mount package. They include the DC/DC controller,inductor, power switches and supporting circuitry.These highly integrated regulators also provide an easysolution for applications that require negative outputvoltages. In other words, these products can operate asinverting buck-boost regulators. As a result, the lowestpotential in the circuit is not the standard 0V, but –VOUT,which must be tied to the μModule regulator’s GND. Allsignals are now referred to –VOUT.
為解決直流逆變交流的問題，有效地利用能源，讓電源輸出最大功率，設計了高性能的基于IR2101最大功率跟蹤逆變器，并以SPMC75F2413A單片機作為主控制器。高電壓、高速功率的MOSFET或IGBT驅動器IR2101采用高度集成的電平轉換技術，同時上管采用外部自舉電容上電，能夠穩定高效地驅動MOS管。該逆變器可以實現DC/AC的轉換，最大功率點的跟蹤等功能。實際測試結果表明，該逆變器系統具有跟蹤能力強，穩定性高，反應靈敏等特點，該逆變器不僅可應用于普通的電源逆變系統，而且可應用于光伏并網發電的逆變系統，具有廣泛的市場前景。
Abstract:
To solve the problem of DC-AC inverter， and to utilize solar energy more efficiently， the design of maximum power point tracking inverter based on IR2101 was achieved with a high-performance， which can make the system output power maximum. SPMC75F2413A was adopted as main controller. IR2101 is a high voltage， high speed power MOSFET and IGBT driver. It adopted highly integrated voltage level transforming technology， and an external bootstrap capacitor was used， which could drive MOS tube efficiently and stably. Many functions are achieved in the system， such as DC/AC conversion， maximun power point tracking， etc. The actual test result shows that the inverter system has characteristics of strong tracking ability， high stability and reacting quickly. The design can not only be used in ordinary power inverter system， but also be used in photovoltaic power inverter system. The design has certain marketing prospects
Designing read/write device (RWD) units for industrial RF-Identification
applications is strongly facilitated by the NXP Semiconductors HITAG
Reader Chip HTRC110. All needed function blocks, like the antenna
driver, modulator demodulator and antenna diagnosis unit, are integrated
in the HTRC110. Therefore only a minimum number of additional passive
components are required for a complete RWD.
This Application Note describes how to design an industrial
RF-Identification system with the HTRC110. The major focus is
dimensioning of the antenna, all other external components including
clock and power supply, as well as the demodulation principle and its
implementatio
