以S3C825A為例介紹三星公司SAM8系列單片機的內部結構及其軟件開發環境，詳細描述采用混合編程法來對SAM8系列單片機進行軟件設計的一般方法，最后給出用混合編程法對S3C825A進行軟件設計的具體應用實例。
Abstract:
With S3C825A,this paper firstly introduces the SAM8 series single-chip microcontrollers and their software development environment, then introduces mixed programming technology for SAM8 series single-chip microcontrollers. In the end, the application program is also given.
介紹了用單片機C 語言實現無功補償中電容組循環投切的基本原理和算法，并舉例說明。關鍵詞：循環投切;C51;無功補償中圖分類號： TM76 文獻標識碼： BAbstract: This paper introduces the aplication of C51 in the controlling of capacitorsuits cycle powered to be on and off in reactive compensation.it illustrate thefondamental principle and algorithm with example.Key words: cycle powered to be on and off; C51; reactive compensation
為提高功率因數，往往采用補償電容的方法來實現。而電容器的容量是由實時功率因數與標準值進行比較來決定的，實時功率因數小于標準值時，需投入電容組，實時功率因數大于標準值時，則需切除電容組。投切方式的不合理，會對電容器造成損壞，現有的控制器多采用“順序投切”方式，在這種投切方式下排序在前的電容器組，先投后切；而后面的卻后投先切。這不僅使處于前面的電容組經常處于運行狀態，積累熱量不易散失，影響其使用壽命，而且使后面的投切開關經常動作，同樣減少壽命。合理的投切方式應為“循環投切”。這種投切方式使先投入的運行的電容組先退出，后投的后切除，從而使各組電容及投切開關使用機率均等，降低了電容組的平均運行溫度，減少了投切開關的動作次數，延長了其使用壽命。
PROTEUS VSM在單片機系統仿真中的應用:：介紹了單片機系統仿真工具PROTEUS VSM 及其在單片機系統仿真中的應用，給出了具體的應用實例，詳細地介紹了PROTEUS VSM 與Keil uVision3的接口方法。關鍵詞：單片機；Keil uVision3；仿真；外圍器件；PROTEUS VSM；
Abstract：This paper introduces the simulation tool for M CU system —PROTEUS VSM ， and presents the application ofPROTEUS VSM in MCU system simulation through an applicable example．The way of interfacing PROTEUS VSM to Keil uVision3is also presented in details．Keywords：MCU ；Keil uVision3；simulation；peripheral devices；PROTEUS VSM ；
本文介紹了一種基于單片機的健身車轉速測量系統。該系統具有電路簡單、使用方便等特點。文中詳細介紹了該系統的工作原理,并且給出了它的硬件原理圖和軟件設計程序框圖。關鍵詞:轉速 單片機 測量ABSTRACT :This paper introduces a measuring system of the rotational velocity of exercise bike based on single - chip microcomputer . It has such advantages : simple circuit ,convenient use and so on. The work principle is presented in detail in this paper and the block diagram of hardware and program flow chart are giv2 en as well .KEYWORDS :Rotational velocity Single - chip microcomputer Measuring
CAN與RS232轉換節點的設計與實現
介紹將CAN總線接口與RS232總線接口相互轉換的設計方法和2種總線電平轉換關系，實現CAN總線與各模塊的接口設計，制定了相應的軟硬件設計方案，并給出軟件設計流程圖以及部分硬件設計原理圖。為CAN總線與RS232總線互聯提供了一種方法，對CAN總線與RS232總線接口設備的互聯和廣泛應用的實現具有重要意義。關鍵詞：CAN總線；RS-232總線；串行通信Design and Realization of CAN and RS232 Transformation NodeZHOU Wei, CHENG Xiao-hong(Information Institute, Wuhan University of Technology, Wuhan 430070)【Abstract】This paper introduces one design method of the CAN bus interface and the RS232 bus interface interconversion, emphasizes two kindof bus level transformation relations, realizes the CAN bus and various modules connection design, formulates the design proposal of correspondingsoftware and hardware, and gives the flow chart of software design as well as the partial schematic diagram of hardware design. It providesonemethod for the CAN bus and the RS232 bus interconnection, has the vital significance to widespread application realization of the CAN busand theRS232 bus interface equipment interconnection.【Key words】CAN bus; RS-232 bus; serial communication
本文主要通過介紹PLC通訊的意義和三菱FX系列PLC的四種通訊方式，并重點介紹FX系列PLC與計算機無協議通訊，主要從無協議通訊的硬件、配線、數據寄存器設置、PLC與計算機無協議通訊的指令用法、PLC程序編寫和計算機VB程序的編寫來說明無協議通訊的過程和一般方法。
My dissertation introduces the significance of PLC communications and the four means of communication of Mitsubishi FX’s PLC, And highlights the no protocol communications of FX series PLC and computer, no protocol communications hardware, wiring, Register data set, and the usage of command about no protocol communications, How to write PLC program and computer VB program to illustrate the process of no protocol communications and general method.
闡述了軌道交通列車定位技術。介紹了在軌道交通系統中列車定位技術的功能，國內外軌道交通中主要采用的列車定位方法，重點論述了幾種主要定位技術，并從定位精度、閉塞制式、維護投資成本、抗干擾等方面進行分析比較。提出目前軌道交通定位技術應綜合運用，取長補短，多種方法相互融合，才能滿足軌道交通中對安全可靠性的要求。
Abstract:
Rail train positioning technology is described. The paper introduces the funetions of the train positioning technology in the rail transit system， the main methods of train positioning do mestic and international rail， and focuses on several key methods， analyzes and compares from the positioning accuracy， block system, maintenance and investment cost， interference and so on， suggested that the current rail positioning technology should be integrated use of positioning method of meriging， learn from each other， to meet the reliability requirements of rail safety.
Nios II軟件構建工具入門
The Nios® II Software Build Tools (SBT) allows you to construct a wide variety of
complex embedded software systems using a command-line interface. From this
interface, you can execute Software Built Tools command utilities, and use scripts
other tools) to combine the command utilities in many useful ways.
This chapter introduces you to project creation with the SBT at the command line
This chapter includes the following sections:
■ “Advantages of Command-Line Software Development”
■ “Outline of the Nios II SBT Command-Line Interface”
■ “Getting Started in the SBT Command Line”
■ “Software Build Tools Scripting Basics” on page 3–8
IBM MQ
Introduction and overview
This chapter describes the scope of this book and introduces WebSphere
Business Integration Message Broker, WebSphere Business Integration Event
Broker, and their main components.
Using a holistic approach to teaching developers the ins-and-outs of GNU/Linux programming using APIs, tools, communication, and scripting, this book introduces programmers to the environment from the lowest layers to the user layers.
