The ability to analyze system or circuit behavior is one of the key requirements for
successful design. To put an idea to work, a designer needs both the knowledge
and tools for analyzing the behavior of that new system architecture or that experi-
mental circuit topology. Design decisions are grounded on the results obtained from
analysis.
Resource allocation is an important issue in wireless communication networks. In
recent decades, cognitive radio technology and cognitive radio-based networks have
obtained more and more attention and have been well studied to improve spectrum
utilization and to overcomethe problem of spectrum scarcity in future wireless com-
munication systems. Many new challenges on resource allocation appear in cogni-
tive radio-based networks. In this book, we focus on effective solutions to resource
allocation in several important cognitive radio-based networks, including a cogni-
tive radio-basedopportunisticspectrum access network, a cognitiveradio-basedcen-
tralized network, a cognitive radio-based cellular network, a cognitive radio-based
high-speed vehicle network, and a cognitive radio-based smart grid.
There exist two essentially different approaches to the study of dynamical systems, based on
the following distinction:
time-continuous nonlinear differential equations ? time-discrete maps
One approach starts from time-continuous differential equations and leads to time-discrete
maps, which are obtained from them by a suitable discretization of time. This path is
pursued, e.g., in the book by Strogatz [Str94]. 1 The other approach starts from the study of
time-discrete maps and then gradually builds up to time-continuous differential equations,
see, e.g., [Ott93, All97, Dev89, Has03, Rob95]. After a short motivation in terms of nonlinear
differential equations, for the rest of this course we shall follow the latter route to dynamical
systems theory. This allows a generally more simple way of introducing the important
concepts, which can usually be carried over to a more complex and physically realistic
context.
The PW2202 is silicon N-channel Enhanced VDMOSFETs, is obtained by the self-aligned planarTechnology which reduce the conduction loss, improve switching performance and enhance theavalanche energy. The transistor can be used in various power switching circuit for system
本系統基于STM32單片機設計的非接觸式電流檢測控制系統,通過OPA548片將所給任意信號放大,由100Ω電阻和INA128芯片進行電流電壓轉換放大后,利用STM32單片機對獲取的電壓信號以0.488μs頻率采樣,利用STM32單片機的FFT庫,獲得信號的諧波信息。測量電流信號精準,該設計可廣泛應用在以STM32單片機為核心控制器件的新型儀表中,性能精準且抗干擾能力強。This system is a non-contact current detection and control system based on STM32 single chip microcomputer. It amplifiesany signal through OPA548 chip, converts and amplifies the current and voltage by 100 Ω resistance and INA128 chip. The obtainedvoltage signal is sampled at the frequency of 0.488 μs by STM 32 single chip microcomputer, and the harmonic information of the signalis obtained by the FFT library of STM 32 single chip microcomputer. The measurement of current signal is accurate. This design can bewidely used in a new instrument with STM 32 single chip microcomputer as its core control device, with accurate performance and stronganti-interference capability.
應用無跡卡爾曼濾波算法（UKF）進行鋰電池的SOC估計,采用Thevenin二階RC等效電路模型,對HPPC電池脈沖充放電實驗數據進行Matlab處理,得到較為準確的模型.通過在Matlab中編寫算法程序,對不同工況的估計值與實際值進行誤差估算及對比分析,通過此算法進行SOC估計,得到該算法可有效降低系統誤差并糾正SOC的初值偏差.The non trace Calman filter （UKF） is applied to the SOC estimation of lithium battery. The Thevenin two order RC equivalent circuit model is used to process the HPPC battery pulse charge discharge experimental data by Matlab processing, and a more accurate model is obtained. By writing algorithm program in Matlab, the error estimation and comparison analysis of the estimated value and actual value of different states are carried out, and the SOC estimation is carried out by this algorithm. The algorithm can effectively reduce the system error and correct the initial value deviation of the SOC.
為了實時檢測血氧量,能使缺氧特別敏感的腦組織或心臟類疾病患者得到及時治療,采用近紅外雙波長透射式光電脈搏血氧測定法,以H橋電路對發射光源進行控制及通用運算放大器搭建濾波電路。運用參數理論計算和計算機仿真結果相對比的方法,通過Mu ltisim軟件對所設計電路進行仿真,仿真結果與理論參數計算相吻合,證明了電路參數設計的可行性,為血氧儀的實物制作提供參考。For real-time detection of oxygen saturation for timely treatment of the brain or heart,which are very sensitive to oxygen inadequacy,the near-infrared wavelengths double photoelectric pulse oximeter transmission method is adopted.The illuminant is controlled with the H bridge circuit and the filter circuit is built with general op-amps.Parameters by theoretical calculation is compared with the computer simulation results in Multisim and satisfactory results are obtained.It is shown that the design of the circuit parameters is feasible and can be a help in making the physical blood-oxygen monitor.
