Abstract: Designers who must interface 1-Wire temperature sensors with Xilinx field-programmable gate arrays(FPGAs) can use this reference design to drive a DS28EA00 1-Wire slave device. The downloadable softwarementioned in this document can also be used as a starting point to connect other 1-Wire slave devices. The systemimplements a 1-Wire master connected to a UART and outputs temperature to a PC from the DS28EA00 temperaturesensor. In addition, high/low alarm outputs are displayed from the DS28EA00 PIO pins using LEDs.
The Virtex™-4 user access register (USR_ACCESS_VIRTEX4) is a 32-bit register thatprovides direct access to bitstream data by the FPGA fabric. It is useful for loadingPowerPC™ 405 (PPC405) processor caches and/or other data into the FPGA after the FPGAhas been configured, thus achieving partial reconfiguration. The USR_ACCESS_VIRTEX4register is programmed through the bitstream with a command that writes a series of 32-bitwords.
The SDI standards are the predominant standards for uncompressed digital videointerfaces in the broadcast studio and video production center. The first SDI standard,SD-SDI, allowed standard-definition digital video to be transported over the coaxial cableinfrastructure initially installed in studios to carry analog video. Next, HD-SDI wasto support high-definition video. Finally, dual link HD-SDI and 3G-SDIdoubled the bandwidth of HD-SDI to support 1080p (50 Hz and 60 Hz) and other videoformats requiring more bandwidth than HD-SDI provides.
多遠程二極管溫度傳感器-Design Considerations for pc thermal management
Multiple RDTS (remote diode temperature sensing) provides the most accurate method of sensing an IC’s junction temperature. It overcomes thermal gradient and placement issues encountered when trying to place external sensors. PCB component count decreases when using a device that provides multiple inputs.Better temperature sensing improves product performance and reliability. Disk drive data integrity suffers at elevated temperatures. IBM published an article stating that a 5°C rise in operating temperature causes a 15% increase in the drive’s failure rate. The overall performance of a system can be improved by providing a more accurate temperature measurement of the most critical devices allowing them to run just a few degrees hotter.The LM83 directly senses its own temperature and the temperature of three external PN junctions. One is dedicated to the CPU of choice, the other two go to other parts of your system that need thermal monitoring such as the disk drive or graphics chip. The SMBus-compatible LM83 supports SMBus timeout and logic levels. The LM83 has two interrupt outputs; one for user-programmable limits and WATCHDOG capability (INT), the other is a Critical Temperature Alarm output (T_CRIT_A) for system power supply shutdown.
A Computer-On-Module, or COM, is a Module with all components necessary for a bootable host computer, packaged as a super component. A COM requires a Carrier Board to bring out I/O and to power up. COMs are used to build single board computer solutions and offer OEMs fast time-to-market with reduced development cost. Like integrated circuits, they provide OEMs with significant freedom in meeting form-fit-function requirements. For all these reasons the COM methodology has gained much popularity with OEMs in the embedded industry. COM Express® is an open industry standard for Computer-On-Modules. It is designed to be future proof and to provide a smooth transition path from legacy parallel interfaces to LVDS (Low Voltage Differential Signaling) interfaces. These include the PCI bus and parallel ATA on the one hand and PCI Express and Serial ATA on the other hand.
Abstract: Counterfeiting as an international industry covers virtually everything made or manufactured,from auto parts to purses and watches to prescription drugs. In contrast to other counterfeit items, the
The CC1101 is a low-cost sub- 1 GHztransceiver designed for very low-powerwireless applications. The circuit is mainlyintended for the ISM (Industrial, Scientific andMedical) and SRD (Short Range Device)frequency bands at 315, 433, 868, and 915MHz, but can easily be programmed foroperation at other frequencies in the 300-348MHz, 387-464 MHz and 779-928 MHz bands.CC1101 is an improved and code compatibleversion of the CC1100 RF transceiver. Themain improvements on the CC1101 include:
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty.
With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications.
Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
Linear Technology offers some of the highest performance RF and signal chain solutions for wireless and cellularinfrastructure. These products support worldwide standards including, LTE, WiMAX, GSM,W-CDMA, TD-SCDMA,CDMA, and CDMA2000. other wireless systems include broadband microwave data links, secure communications,satellite receivers, broadband wireless access, wireless broadcast systems, RFID readers and cable infrastructure
Abstract: This application note illustrates the flexibility of the MAX7060 ASK/FSK transmitter. While the currently available evaluationkit (EV kit) has been optimized for the device's use in a specific frequency band (i.e., 288MHz to 390MHz), this document addresseshow the EV kit circuitry can be modified for improved operation at 433.92MHz, a frequency commonly used in Europe. Twoalternative match and filter configurations are presented: one for optimizing drain efficiency, the other for achieving higher transmitpower. Features and capabilities of earlier Maxim industrial, scientific, and medical radio-frequency (ISM-RF) transmitters areprovided, allowing comparison of the MAX7060 to its predecessors. Several design guidelines and cautions for using the MAX7060are discussed.
