針對嵌入式機器視覺系統向獨立化、智能化發展的要求，介紹了一種嵌入式視覺系統--智能相機。基于對智能相機體系結構、組成模塊和圖像采集、傳輸和處理技術的分析，對國內外的幾款智能相機進行比較。綜合技術發展現狀，提出基于FPGA+DSP模式的硬件平臺，并提出智能相機的發展方向。分析結果表明，該系統設計可以實現脫離PC運行，完成圖像獲取與分析，并作出相應輸出。 Abstract: This paper introduced an embedded vision system-intelligent camera ，which was for embedded machine vision systems to an independent and intelligent development requirements. Intelligent camera architecture， component modules and image acquisition， transmission and processing technology were analyzed. After comparing integrated technology development of several intelligent cameras at home and abroad， the paper proposed the hardware platform based on FPGA+DSP models and made clear direction of development of intelligent cameras. On the analysis of the design， the results indicate that the system can run from the PC independently to complete the image acquisition and analysis and give a corresponding output.
標簽： FPGA DSP 模式 智能相機
上傳時間： 2013-11-14
上傳用戶：無聊來刷下
為了在CDMA系統中更好地應用QDPSK數字調制方式，在分析四相相對移相（QDPSK)信號調制解調原理的基礎上，設計了一種QDPSK調制解調電路，它包括串并轉換、差分編碼、四相載波產生和選相、相干解調、差分譯碼和并串轉換電路。在MAX+PLUSⅡ軟件平臺上，進行了編譯和波形仿真。綜合后下載到復雜可編程邏輯器件EPM7128SLC84-15中，測試結果表明，調制電路能正確選相，解調電路輸出數據與QDPSK調制輸入數據完全一致，達到了預期的設計要求。 Abstract: In order to realize the better application of digital modulation mode QDPSK in the CDMA system， a sort of QDPSK modulation-demodulation circuit was designed based on the analysis of QDPSK signal modulation-demodulation principles. It included serial/parallel conversion circuit, differential encoding circuit, four-phase carrier wave produced and phase chosen circuit, coherent demodulation circuit, difference decoding circuit and parallel/serial conversion circuit. And it was compiled and simulated on the MAX+PLUSⅡ software platform,and downloaded into the CPLD of EPM7128SLC84-15.The test result shows that the modulation circuit can exactly choose the phase，and the output data of the demodulator circuit is the same as the input data of the QDPSK modulate. The circuit achieves the prospective requirement of the design.
標簽： QDPSK CPLD 調制解調 電路設計
上傳時間： 2013-10-28
上傳用戶：jyycc
波長信號的解調是實現光纖光柵傳感網絡的關鍵，基于現有的光纖光柵傳感器解調方法，提出一種基于FPGA的雙匹配光纖光柵解調方法，此系統是一種高速率、高精度、低成本的解調系統，并且通過引入雙匹配光柵有效地克服了雙值問題同時擴大了檢測范圍。分析了光纖光柵的測溫原理并給出了該方案軟硬件設計，綜合考慮系統的解調精度和FPGA的處理速度給出了基于拉格朗日的曲線擬合算法。 Abstract: Sensor is one of the most important application of the fiber grating. Wavelength signal demodulating is the key techniques to carry out fiber grating sensing network， based on several existing methods of fiber grating sensor demodulation inadequate， a two-match fiber grating demodulation method was presented. This system is a high-speed， high precision， low-cost demodulation system. And by introducing a two-match grating effectively overcomes the problem of double value while expands the scope of testing. This paper analyzes the principle of fiber Bragg grating temperature and gives the software and hardware design of the program. Considering the system of demodulation accuracy and processing speed of FPGA，this paper gives the curve fitting algorithm based on Lagrange.
標簽： FPGA 光纖光柵 解調系統
上傳時間： 2013-10-10
上傳用戶：zxc23456789
Integrated EMI/Thermal Design forSwitching Power SuppliesWei ZhangThesis submitted to the Faculty of theVirginia Polytechnic Institute and State Universityin partial fulfillment of the requirements for the degree of Integrated EMI/Thermal Design forSwitching Power SuppliesWei Zhang(ABSTRACT)This work presents the modeling and analysis of EMI and thermal performancefor switch power supply by using the CAD tools. The methodology and design guidelinesare developed.By using a boost PFC circuit as an example, an equivalent circuit model is builtfor EMI noise prediction and analysis. The parasitic elements of circuit layout andcomponents are extracted analytically or by using CAD tools. Based on the model, circuitlayout and magnetic component design are modified to minimize circuit EMI. EMI filtercan be designed at an early stage without prototype implementation.In the second part, thermal analyses are conducted for the circuit by using thesoftware Flotherm, which includes the mechanism of conduction, convection andradiation. Thermal models are built for the components. Thermal performance of thecircuit and the temperature profile of components are predicted. Improved thermalmanagement and winding arrangement are investigated to reduce temperature.In the third part, several circuit layouts and inductor design examples are checkedfrom both the EMI and thermal point of view. Insightful information is obtained.
標簽： EMI 開關電源 英文
上傳時間： 2013-11-16
上傳用戶：萍水相逢
a8259 可編程中斷控制 altera提供 The a8259 is designed to simplify the implementation of the interrupt interface in 8088 and 8086 based microcomputer systems. The device is known as a programmable interrupt controller. The a8259 receives and prioritizes up to 8 interrupts, and in the cascade mode, this can be expanded up to 64 interrupts. An asynchronous reset and a clock input have been added to improve operation and reliability.
上傳時間： 2015-01-02
上傳用戶：panpanpan
為了提高直接轉矩控制（DTC）系統定子磁鏈估計精度，降低電流、電壓測量的隨機誤差，提出了一種基于擴展卡爾曼濾波（EKF）實現異步電機轉子位置和速度估計的方法。擴展卡爾曼濾波器是建立在基于旋轉坐標系下由定子電流、電壓、轉子轉速和其它電機參量所構成的電機模型上，將定子電流、定子磁鏈、轉速和轉子角位置作為狀態變量，定子電壓為輸入變量，定子電流為輸出變量，通過對磁鏈和轉速的閉環控制提高定子磁鏈的估計精度，實現了異步電機的無速度傳感器直接轉矩控制策略，仿真結果驗證了該方法的可行性,提高了直接轉矩的控制性能。 Abstract: In order to improve the Direct Torque Control（DTC） system of stator flux estimation accuracy and reduce the current， voltage measurement of random error， a novel method to estimate the speed and rotor position of asynchronous motor based on extended Kalman filter was introduced. EKF was based on d-p axis motor and other motor parameters （state vector: stator current， stator flux linkage， rotor angular speed and position； input: stator voltage； output: staror current). EKF was designed for stator flux and rotor speed estimation in close-loop control. It can improve the estimated accuracy of stator flux. It is possible to estimate the speed and rotor position and implement asynchronous motor drives without position and speed sensors. The simulation results show it is efficient and improves the control performance.
標簽： EKF 異步電機 直接轉矩 控制系統
上傳時間： 2015-01-02
上傳用戶：qingdou
Logger iButton devices have gained a lot of popularity with researchers. Although free evaluation software is easy to use and welldocumented, the choices and inputs that need to be made can sometimes be challenging. This application note explains technicalterms that are common with temperature logger iButtons and how they relate to each other. Additionally, it presents an algorithm tohelp users choose the necessary input parameters, including the sample rate based on a user's needs and the available memory tostore the data.
上傳時間： 2013-11-16
上傳用戶：xywhw1
Semiconductor memory, card readers, microprocessors,disc drives, piezoelectric devices and digitally based systemsfurnish transient loads that a voltage regulator mustservice. Ideally, regulator output is invariant during a loadtransient. In practice, some variation is encountered andbecomes problematic if allowable operating voltage tolerancesare exceeded. This mandates testing the regulatorand its associated support components to verify desiredperformance under transient loading conditions. Variousmethods are employable to generate transient loads, allowingobservation of regulator response
標簽： 如何測試 穩壓器 瞬態響應 負載
上傳時間： 2013-11-21
上傳用戶：semi1981
基于通用集成運算放大器，利用MASON公式設計了一個多功能二階通用濾波器，能同時或分別實現低通、高通和帶通濾波，也能設計成一個正交振蕩器。電路的極點頻率和品質因數能夠獨立、精確地調節。電路使用4個集成運放、2個電容和11個電阻，所有集成運放的反相端虛地。利用計算機仿真電路的通用濾波功能、極點頻率和品質因數的獨立控制和正交正弦振蕩，從而證明該濾波器正確有效。 Abstract: A new multifunctional second-order filter based on OPs was presented by MASON formula. Functions， such as high-pass， band-pass， low-pass filtering， can be realized respectively and simultaneously， and can become a quadrature oscillator by modifying resistance ratio. Its pole angular frequency and quality factor can be tuned accurately and independently. The circuit presented contains four OPs， two capacitors， and eleven resistances， and inverting input of all OPs is virtual ground. Its general filtering， the independent control of pole frequency and quality factor and quadrature sinusoidal oscillation were simulated by computer， and the result shows that the presented circuit is valid and effective.
標簽： MASON 多功能 二階 濾波器設計
上傳時間： 2013-10-09
上傳用戶：13788529953
在Multisim 10軟件環境下，設計一種由運算放大器構成的精確可控矩形波信號發生器，結合系統電路原理圖重點闡述了各參數指標的實現與測試方法。通過改變RC電路的電容充、放電路徑和時間常數實現了占空比和頻率的調節，通過多路開關投入不同數值的電容實現了頻段的調節，通過電壓取樣和同相放大電路實現了輸出電壓幅值的調節并提高了電路的帶負載能力，可作為頻率和幅值可調的方波信號發生器。Multisim 10仿真分析及應用電路測試結果表明，電路性能指標達到了設計要求。 Abstract: Based on Multisim 10， this paper designed a kind of rectangular-wave signal generator which could be controlled exactly composed of operational amplifier， the key point was how to implement and test the parameter indicators based on the circuit diagram. The duty and the frequency were adjusted by changing the time constant and the way of charging and discharging of the capacitor， the width of frequency was adjusted by using different capacitors provided with multiple switch， the amplitude of output voltage was adjusted by sampling voltage and using in-phase amplifier circuit，the ability of driving loads was raised， the circuit can be used as squarewave signal generator whose frequency and amplitude can be adjusted. The final simulation results of Multisim 10 and the tests of applicable circuit show that the performance indicators of the circuit meets the design requirements.
標簽： Multisim 矩形波 信號發生器 仿真
上傳時間： 2014-01-21
上傳用戶：shen007yue
蟲蟲下載站版權所有 京ICP備2021023401號-1
