本論文設計了一種基于FPGA的高速FIR數字濾波器,濾波器實現低通濾波,截止頻率為1MHz,通帶波紋小于1 dB,阻帶最大衰減為-40 dB,輸入輸出數據為8位二進制,采樣頻率為10MHz。 論文首先簡要介紹了數字濾波器的基本原理和線性FIR數字濾波器的性質、結構,根據濾波器的性能要求選擇窗函數、確定系數,在算法上為了滿足數字濾波器的要求,對系數放大512倍并取整,并用Matlab對數字濾波器原理進行了證明。同時簡述了EDA技術和FPGA設計流程。 其次,論文說明了FIR數字濾波器模塊的劃分,并用Verilog語言在Modelsim環境下進行了功能測試。對于數字濾波器系數中的-1,-2,4這些簡單的系數乘法直接進行移位和取反,可以極大的節省資源和優化設計。而對普通系數乘法采用4-BANT(4bits-at-a-time)的并行算法,用加法累加快速實現了乘積的運算；另外,在本設計進行部分積累加時,采用舍取冗余位,主要是根據設計時已對系數進行了放大,而輸出時又要將結果相應的縮小,所以在累加時,提前對部分積縮小,從而減少了運算量,從時間和資源上都得到了優化。 論文的最后分別用Modelsim和Quartus II進行了FIR數字濾波器的前仿真和后仿真,將仿真的結果和Matlab中原理驗證時得到的理想值進行了比較,并對所產生的誤差進行了分析。仿真結果表明：本16階FIR數字濾波器設計能夠實現截止頻率為1MHz的低通濾波,并且工作頻率可達150MHz以上。
上傳時間： 2013-07-15
上傳用戶：lanwei
華為的MG323 TCP/IP 常用AT命令
上傳時間： 2013-04-24
上傳用戶：jacking
適用于64位系統的AT單片機下載軟件，avr fighter 很適用，已調試！！！
上傳時間： 2013-04-24
上傳用戶：f1364628965
電腦硬件更新換代快，而主機電源更新較慢，十幾年的發展，就是由AT結構變化為ATX電源。
上傳時間： 2013-05-18
上傳用戶：小小小熊
M AT L A B是一個可視化的計算程序，被廣泛地使用于從個人計算機到超級計算機范圍內 的各種計算機上。 M AT L A B包括命令控制、可編程，有上百個預先定義好的命令和函數。這些函數能通過 用戶自定義函數進一步擴展。 M AT L A B有許多強有力的命令。例如， M AT L A B能夠用一個單一的命令求解線性系統， 能完成大量的高級矩陣處理。 M AT L A B有強有力的二維、三維圖形工具。 M AT L A B能與其他程序一起使用。例如， M AT L A B的圖形功能，可以在一個 F O RT R A N 程序中完成可視化計
上傳時間： 2013-04-24
上傳用戶：xinshou123456
This document was developed under the Standard Hardware and Reliability Program (SHARP) TechnologyIndependent Representation of Electronic Products (TIREP) project. It is intended for use by VHSIC HardwareDescription Language (VHDL) design engineers and is offered as guidance for the development of VHDL modelswhich are compliant with the VHDL Data Item Description (DID DI-EGDS-80811) and which can be providedto manufacturing engineering personnel for the development of production data and the subsequent productionof hardware. Most VHDL modeling performed to date has been concentrated at either the component level orat the conceptual system level. The assembly and sub-assembly levels have been largely disregarded. Under theSHARP TIREP project, an attempt has been made to help close this gap. The TIREP models are based upon lowcomplexity Standard Electronic Modules (SEM) of the format A configuration. Although these modules are quitesimple, it is felt that the lessons learned offer guidance which can readily be applied to a wide range of assemblytypes and complexities.
上傳時間： 2014-12-23
上傳用戶：xinhaoshan2016
電位計訊號轉換器 AT-PM1-P1-DN-ADL 1．產品說明 AT系列轉換器/分配器主要設計使用于一般訊號迴路中之轉換與隔離；如 4~20mA、0~10V、熱電偶(Type K, J, E, T)、熱電阻(Rtd-Pt100Ω)、荷重元、電位計(三線式)、電阻(二線式)及交流電壓/電流等訊號，機種齊全。 此款薄型設計的轉換器/分配器，除了能提供兩組訊號輸出（輸出間隔離）或24V激發電源供傳送器使用外，切換式電源亦提供了安裝的便利性。上方并設計了電源、輸入及輸出指示燈及可插拔式接線端子方便現場施工及工作狀態檢視。 2.產品特點 可選擇帶指撥開關切換，六種常規輸出信號0-5V/0~10V/1~5V/2~10V/4~20mA/ 0~20mA 可自行切換。 雙回路輸出完全隔離，可選擇不同信號。 設計了電源、輸入及輸出LED指示燈，方便現場工作狀態檢視。 規格選擇表中可指定選購0.1%精度 17.55mm薄型35mm導軌安裝。 依據CE國際標準規范設計。 3.技術規格 用途：信號轉換及隔離 過載輸入能力：電流：10×額定10秒 第二組輸出：可選擇 輸入范圍：P1：0 Ω ~ 50.0 Ω / ~ 2.0 KΩ P2：0 Ω ~ 2.0 KΩ / ~ 100.0 KΩ 精確度: ≦±0.2% of F.S. ≦±0.1% of F.S. 偵測電壓：1.6V 輸入耗損: 交流電流:≤ 0.1VA; 交流電壓:≤ 0.15VA 反應時間: ≤ 250msec (10%~90% of FS) 輸出波紋: ≤ ±0.1% of F.S. 滿量程校正范圍:≤ ±10% of F.S.，2組輸出可個別調整 零點校正范圍:≤ ±10% of F.S.，2組輸出可個別調整 隔離:AC 2.0 KV 輸出1與輸出2之間 隔離抗阻：DC 500V 100MΩ 工作電源: AC 85~265V/DC 100~300V, 50/60Hz 或 AC/DC 20~56V (選購規格) 消耗功率: DC 4W, AC 6.0VA 工作溫度: 0~60 ºC 工作濕度: 20~95% RH, 無結露 溫度系數: ≤ 100PPM/ ºC (0~50 ºC) 儲存溫度: -10~70 ºC 保護等級: IP 42 振動測試: 1~800 Hz, 3.175 g2/Hz 外觀尺寸: 94.0mm x 94.0mm x 17.5mm 外殼材質: ABS防火材料，UL94V0 安裝軌道: 35mm DIN導軌 (EN50022) 重量: 250g 安全規范(LVD): IEC 61010 (Installation category 3) EMC: EN 55011:2002; EN 61326:2003 EMI: EN 55011:2002; EN 61326:2003 常用規格：AT-PM1-P1-DN-ADL 電位計訊號轉換器，一組輸出，輸入范圍：0 Ω ~ 50.0 Ω / ~ 2.0 KΩ，輸出一組輸出4-20mA，工作電源AC/DC20-56V
上傳時間： 2013-11-05
上傳用戶：feitian920
The LT®6552 is a specialized dual-differencing 75MHzoperational amplifier ideal for rejecting common modenoise as a video line receiver. The input pairs are designedto operate with equal but opposite large-signal differencesand provide exceptional high frequency commonmode rejection (CMRR of 65dB at 10MHz), therebyforming an extremely versatile gain block structure thatminimizes component count in most situations. The dualinput pairs are free to take on independent common modelevels, while the two voltage differentials are summedinternally to form a net input signal.
上傳時間： 2014-12-23
上傳用戶：13691535575
A fully differential amplifi er is often used to converta single-ended signal to a differential signal, a designwhich requires three signifi cant considerations: theimpedance of the single-ended source must match thesingle-ended impedance of the differential amplifi er,the amplifi er’s inputs must remain within the commonmode voltage limits and the input signal must be levelshifted to a signal that is centered at the desired outputcommon mode voltage.
上傳時間： 2013-11-09
上傳用戶：wweqas
Most circuit designers are familiar with diode dynamiccharacteristics such as charge storage, voltage dependentcapacitance and reverse recovery time. Less commonlyacknowledged and manufacturer specifi ed is diode forwardturn-on time. This parameter describes the timerequired for a diode to turn on and clamp at its forwardvoltage drop. Historically, this extremely short time, unitsof nanoseconds, has been so small that user and vendoralike have essentially ignored it. It is rarely discussed andalmost never specifi ed. Recently, switching regulator clockrate and transition time have become faster, making diodeturn-on time a critical issue. Increased clock rates aremandated to achieve smaller magnetics size; decreasedtransition times somewhat aid overall effi ciency but areprincipally needed to minimize IC heat rise. At clock speedsbeyond about 1MHz, transition time losses are the primarysource of die heating.
上傳時間： 2013-10-10
上傳用戶：誰偷了我的麥兜
