The LTC®3562 quad output step-down regulator is designedfor multicore handheld microprocessor applications thatoperate from a single Li-Ion battery. Its four monolithic, higheffi ciency buck regulators support Intel’s mobile CPU P-Stateand C-State energy saving operating modes. The outputvoltages are independently controllable via I2C, and eachoutput can be independently started and shut down. Designerscan choose from power saving pulse-skipping mode orBurst Mode® operation, or select low noise LDO mode. Thespace-saving LTC3562 is available in a 3mm × 3mm QFNpackage and requires few external components.
針對目前燃氣灶市場的狀況，提出一種基于PIC16C711單片機的燃氣灶脈沖點火控制器設計,具體包括有系統的組成和功能介紹、硬件電路設計及軟件功能實現。
Abstract:
Aiming at today’s gas cooker market, a pulse ignition controler design based on PIC16C711 is presented.The specific descriptions of system components and functions,hardware circuit design and software function are given.
針對材料試驗機等設備中要求測量或控制材料拉伸或壓縮的位移，一般采用光電軸角編碼器檢測位置信號，輸出正交編碼脈沖信號。若采用其他方法檢測位置信號，必然導致電路設計復雜，可靠性降低。因此，提出一種基于LS7266R1的電子式萬能材料試驗機設計方案。給出了試驗機中的控制器工作原理，LS7266R1與單片機的接口硬件設計，以及主程序軟件流程圖。巧妙地把力量傳感器，位移傳感器等機械運動狀態的壓力或拉力以及位置坐標，變成了電壓信號和電脈沖數字信號，供A/D測量和LS7266R1計數，從而實現了獨立完成材料試驗控制或通過PC機串口命令完成材料試驗控制。
Abstract:
Aiming at the requirement that the displacement of the tension and compression always be tested and controlled in the equipement such as material testing machine. The position signal was tested by photoelectric axial angle coder. Therefore， the paper proposes the design of electronic universal testing machine design based on LS7266R1. If the position signal detected by other methods， will inevitably lead to the circuit design complexity， reliability decreased. The work theory of the controller， the hardware interface design between LS7266R1 and single chip， and the flow chart of main program， are presented in this paper. The signal of the compression or tension power and displacement at working， which tested by power sensor and displacement sensor especially， is changed into electric voltage and electric pulse numerical signals. And these signals can be tested by A/D and counted by LS7266R1. Finally the test of the material properties can be controlled by itself， or controlled by the COM command of PC.
This application report discusses the design of non-invasive optical plethysmographyalso called as pulsoximeter using the MSP430FG437 Microcontroller (MCU). Thepulsoximeter consists of a peripheral probe combined with the MCU displaying theoxygen saturation and pulse rate on a LCD glass. The same sensor is used for bothheart-rate detection and pulsoximetering in this application. The probe is placed on aperipheral point of the body such as a finger tip, ear lobe or the nose. The probeincludes two light emitting diodes (LEDs), one in the visible red spectrum (660nm) andthe other in the infrared spectrum (940nm). The percentage of oxygen in the body isworked by measuring the intensity from each frequency of light after it transmitsthrough the body and then calculating the ratio between these two intensities.
基于PIC單片機的脈沖電源:設計了一種金屬凝固過程用脈沖電源。該電源采用PIC16F877作為主控芯片，實現對窄脈沖電流幅值的檢測，以及時電流脈沖幅值根據模糊PID算法進行閑環控制。使用結果表明：該電源的輸出脈沖波形良好，電流幅值穩定，滿足合金材料凝固過程的工藝要求且運行穩定可靠。關鍵詞：脈沖電源；PIC16F877單片機；模糊PID；閑環控制
Abstract：A kind of pulse power supply was designed which uses in the metal solidification process ．．I11is power supply used PIC16F877 to take the master control chip reali on to the narrow pulse electric current peak-to-peak value examination，carried on the closed-loop control to the electric current pulse peak-to-peak value basis fuzzy PID algorithm．The use result indicated ，this power supply output se profile is good，and the electric current peak-to-p~k value is stable，It satisfies the alloy material solidification process the technological requirement and movement stable reliable，Key words：p se po wer supply；PIC16F877single-chip microcontroller；f r PID；closed-loop control
基于單片機的步進電機開環控制系統:通過ATMEL89C51單片機對步進電機進行控制,主要介紹了步進電機控制器、驅動電路和LED顯示電路的設計,實現了步進電機的開環控制。在步進電機控制器的設計中,重點闡述了脈沖產生電路以及對速度的控制。該系統具有成本低、控制方便的特點。關鍵詞: 單片機; 步進電機; 開環控制
Abstract: The design using ATMEL89C51 single chip to control the step2motor with its controller, driving circuit and LED disp lay circuit to realize step motor open2loop controlwere introduced. For the controller in this design,the circuit to p roduce pulse and the speed controlwere expatiated emphatically. This system possesses features of lower cost, easier control.Key words: single ch ip; step2motor; open2loop con trol
Internal Interrupts are used to respond to asynchronous requests from a certain part of themicrocontroller that needs to be serviced. Each peripheral in the TriCore as well as theBus Control Unit, the Debug Unit, the Peripheral Control Processor (PCP) and the CPUitself can generate an Interrupt Request.So what is an external Interrupt?An external Interrupt is something alike as the internal Interrupt. The difference is that anexternal Interrupt request is caused by an external event. Normally this would be a pulseon Port0 or Port1, but it can be even a signal from the input buffer of the SSC, indicatingthat a service is requested.The User’s Manual does not explain this aspect in detail so this ApNote will explain themost common form of an external Interrupt request. This ApNote will show that there is aneasy way to react on a pulse on Port0 or Port1 and to create with this impulse an InterruptService Request. Later in the second part of the document, you can find hints on how todebounce impulses to enable the use of a simple switch as the input device.Note: You will find additional information on how to setup the Interrupt System in theApNote “First steps through the TriCore Interrupt System” (AP3222xx)1. It would gobeyond the scope of this document to explain this here, but you will find selfexplanatoryexamples later on.
The 87C576 includes two separate methods of programming theEPROM array, the traditional modified Quick-Pulse method, and anew On-Board Programming technique (OBP).Quick Pulse programming is a method using a number of devicepins in parallel (see Figure 1) and is the traditional way in which87C51 family members have been programmed. The Quick-Pulsemethod supports the following programming functions:– program USER EPROM– verify USER EPROM– program KEY EPROM– program security bits– verify security bits– read signature bytesThe Quick-Pulse method is quite easily suited to standardprogramming equipment as evidenced by the numerous vendors of87C51 compatible programmers on the market today. Onedisadvantage is that this method is not well suited to programming inthe embedded application because of the large number of signallines that must be isolated from the application. In addition, parallelsignals from a programmer would need to be cabled to theapplication’s circuit board, or the application circuit board wouldneed to have logic built-in to perform the programming functions.These requirements have generally made in-circuit programmingusing the modified Quick Pulse method impractical in almost all87C51 family applications.
