The MAX9257/MAX9258 programmable serializer/deserializer (SerDes) devices transfer both video data and control signals over the same twisted-pair cable. However, control data can only be transmitted during the vertical blank time, which is indicated by the control-channel-enabled output (CCEN) signal. The electronic control unit (ECU) firmware designer needs to know how quickly to respond to the CCEN signal before it times out and how to calculate this duration. This application note describes how to calculate the duration of the CCEN for the MAX9257/MAX9258 SerDes chipset. The calculation is based on STO timeout, clock frequency, and UART bit timing. The CCEN duration is programmable and can be closed if not in use.
標簽： SerDes MAXX 9257 9258
上傳時間： 2014-01-24
上傳用戶：xingisme
針對科研實驗中對拉壓千斤頂加載過程控制的需要，采用ATmega128單片機控制步進電機進而實現對執行系統的電動泵站實行自動控制。對力和位移的數據采集與處理及用步進電機控制電動泵站手柄的技術細節作了重點描述。通過單片機的A/D變換器對AMP放大模塊采集的電橋信號作量化處理，千斤頂?shù)牟倏厥直恢靡离妱?dòng)油泵閥門開啟的方向和大小作若干定位，單片機根據力或位移傳感器信號，實時控制步進電機驅動手柄旋轉到相應操控位置。 Abstract: This article describes the use of ATmega128 AVR microcontroller series of DBS electric pumping stations and QF100/200 separate twoway hydraulic jack to automate the process of manipulating the work of the technical content. Articles on force and displacement data acquisition and processing， and stepper motor control electric pump with the handle of the key technical details were described. Through the MCU’s A / D converter module is collected on the AMP amplification quantify the signal bridge， jack handle position control valve opening according to the direction of electric pumps for a number of positioning and size of the microcontroller based on force or displacement sensor signals， real-time control stepper motor drive control handle rotate to the appropriate location.
標簽： AVR 單片機 閉環控制
上傳時間： 2014-01-16
上傳用戶：hasan2015
Designing Boards with Atmel AT89C51,AT89C52, AT89C1051, and AT89C2051 for Writing Flash at In-Circuit Test. Recent improvements in chips and testers have made it possible for the tester to begin taking over the role tradi-tionally assigned to the PROM program-mer. Instead of having a PROM pro- grammer write nonvolatile memories before assembling the board, the in-cir- cuit tester writes them during in-circuit testing operations. Many Teradyne Z18- series testers are now in use loading code into nonvolatile memories, micro- controllers and in-circuit programmable logic devices. The purpose of this note is to explain how the Z18 approaches the writing task for Atmel AT89C series IC’s, so that designers of boards using these chips can get the best results.
上傳時間： 2013-11-17
上傳用戶：xiaozhiqban
現有基于MAX7219芯片的數碼管驅動電路只適用于小尺寸LED，為擴展其使用范圍，在介紹動態顯示芯片MAX7219功能的基礎上，提出了一個基于該芯片的8位高亮度8英寸數碼管驅動電路。電路保留了MAX7219芯片的功能強大、編程簡單等優點，通過74LS273鎖存器和ULN2803達林頓驅動器，實現了對任意大尺寸數碼管提供較高電壓和電流驅動的靜態顯示，并亮度可調。 Abstract: The existing display-driving circuit based on MAX7219 was only applicable to small-size LED. To expand its use, based on the function introduction of dynamic display chip MAX7219, a display-driving circuit for high-brightness 8-bit LED with the size of 8-inch was proposed. The advantages of MAX7219 were retained, such as powerful function and simple programming. Static display with adjustable brightness for large-size LED with higher voltage and current was achieved with the help of 74LS273 and ULN2803.
標簽： 7219 MAX LED 數碼顯示
上傳時間： 2013-10-23
上傳用戶：31633073
為提高太陽能的利用率，以ATmega8單片機為控制核心，設計了一套光電跟蹤與視日運動軌跡跟蹤互補控制的雙軸太陽跟蹤器。該跟蹤器在晴天時，利用光敏電阻采集光強判斷太陽位置,控制步進電機實現光電跟蹤；在陰天時，采集時鐘器件PCF8583的時間信息,計算當前太陽位置來實現視日運動軌跡跟蹤。實驗表明：該太陽跟蹤器能在不同天氣狀況下對太陽進行較準確地跟蹤，能量接收效率提高了30%，達到充分利用太陽能的目的。 Abstract: To improve the utilization rate of solar energy，a kind of solar tracking controller which effectively combined the sun angle tracking and photo electric tracking based on ATmega8is designed.In the sunny days，the solar tracking con-troller determines the sun's position by using photosensitive resistances to collect light intensity and control stepper motors to achieve photo electric tracking，n cloudy days，it collects clock chip PCF8583time information to calculate the current position of the sun and achieve the sun angle tracking.Experimental results show the solar tracking controller accurately tracks the sun in different weather conditions，improves received energy efficiency by30%and reaches the purpose of full use of solar energy.
上傳時間： 2013-10-15
上傳用戶：urgdil
介紹一種基于CAN總線的牽引變電站自動化系統通訊規約的設計，CAN通訊規約采用標準幀，報文采用主動發送和發送查詢兩種處理形式。該設計在城市輕軌與地鐵牽引變電站中的應用表明：可實現間隔層和通訊處理層的數據快速、可靠的交換，提高牽引變電站的安全性和穩定性 。 Abstract: This paper firstly presents a kind of design dealing with communicational protocol to the traction substation automation system based on CAN bus,and then comes up with the ideas that all frames of CAN communicational protocol should adopt the standard frame,and that messages be processed by two ways:sending initiatively and sending quiries.Subway and light rail application shows that the use of the CAN bus is possible to exchange data quickly and reliably between the layers of the middle and the communicational processing,hence to improve the safety and stability of traction substations.
上傳時間： 2013-11-07
上傳用戶：bs2005
在汽車發動機起動時，若發動機起動后起動機不能及時斷電，將會燒毀起動機或損壞飛輪齒環；若變速器不在空檔位置起動，則起動機的瞬間動力將使汽車位移，還可能引起交通事故和人身安全。為此介紹一種利用NXP P89LPC901單片機控制的汽車起動保護控制器，通過檢測汽車起動開關、變速箱檔位、發動機轉速，實現對汽車發動機起動過程檢測和保護。起動保護控制器在發動機起動過程中通過采用逐個關閉打開負載系統，解決汽車發動機過程中因起動電流大而對汽車電源的沖擊影響,延長了電瓶壽命。 Abstract: When the automotive engine is started, the engine start motor and flywheel gear may be damaged， even traffic accidents and personal safeties may be caused by wrong operation or other factors.In order to ensure the automotive engine can be started normally and safely,it is necessary that the protecting measures and methods are considered in the automotive electrical control system.This paper introduces a kind of the automotive engine starting protect controller based on NXP P89LPC901 MCU.The controller can protect the engine starting process by detecting the starter key switch,transmission stall and engine speed.Through the use of close and open load system,the controller can solve the impact on automotive power because of the high-current load in the process of the automobile engine starting, and extend battery life.
上傳時間： 2013-10-15
上傳用戶：mikesering
Mega16是一款采用先進RISC精簡指令，內置A/D的8位單片機，可支持低電壓聯機 Flash和EEPROM 寫入功能；同時還支持 Basic和C 等高級語言編程。用它設計電子時鐘不僅成本低，硬件簡單，而且很容易實現系統移植。介紹了如何利用AVR系列單片機Mega16及1602字符液晶來設計電子時鐘的方法，同時給出了相應的電路原理及部分語言程序。 Abstract: ?Mega16 is a high-performance, low power consumption, the use of advanced RISC concise instructions, built-in A/D 8-bit microcontrollers, the on-line support for low-voltage Flash, EEPROM write function. Except Mega16 also support the Basic, C, and other high-level language programming.The electronic clock which is deisgned by Mega16 is not only low-cost, simple hardware, but easy to achieve system migration.The design method of electrioic clock based on the AVR Mega16 and character LCD1602 is introduced in this paper,and the corresponding circuit electrionic and some language program are given.
上傳時間： 2014-12-27
上傳用戶：zl5712176
在需要實時大量輸入漢字的顯示控制處理應用中，利用傳統單片機實現顯示控制的設計方法是較難實現的。帶漢字字庫的液晶模塊的使用使得小容量ROM單片機的大量漢字信息輸入與顯示成為可能。提出了針對漢字字庫編碼的二級索引拼音輸入檢索方法,介紹了以ST7920作為控制器的帶漢字字庫的液晶顯示模塊的接口方法及漢字顯示和控制原理，給出了通用計算機鍵盤在單片機中的串行接口，采用該技術可大大增強單片機的漢字輸入功能。為小容量ROM單片機的大批量漢字信息處理提供了一種漢字輸入解決方案。 Abstract: It is difficult to realize Chinese characters input method based on the embedded system by using the traditional design method of display control. It is possible to input and display Chinese characters based on the embedded system with the ROM of small content by using the LCD module with Chinese characters.Chinese characters input method of the quadric index recall in allusion to Chinese characters code is brought forward.The interface and the principle of Chinese characters display control based on the LCD module controlled with the ST7920 is introduced too.The serial interface of the computer keyboard in common use and the embedded system is given at the same time. It can enhance the embedded system function of Chinese characters input by using this technology, and provide a kind of Chinese characters input scheme for the embedded system with small capacity ROM.
上傳時間： 2013-11-19
上傳用戶：jhksyghr
The PCF8578 is a low power CMOS1 LCD row and column driver, designed to drive dotmatrix graphic displays at multiplex rates of 1:8, 1:16, 1:24 or 1:32. The device has40 outputs, of which 24 are programmable and configurable for the following ratios ofrows/columns: 32¤8, 24¤16, 16¤24 or 8¤32. The PCF8578 can function as a stand-alone LCDcontroller and driver for use in small systems. For larger systems it can be used inconjunction with up to 32 PCF8579s for which it has been optimized. Together these twodevices form a general purpose LCD dot matrix driver chip set, capable of driving displaysof up to 40960 dots. The PCF8578 is compatible with most microcontrollers andcommunicates via a two-line bidirectional bus (I2C-bus). Communication overhead isminimized by a display RAM with auto-incremented addressing and display bankswitching.
標簽： 8578 PCF LCD 圖形點陣
上傳時間： 2013-10-23
上傳用戶：頂?shù)弥?/p>
蟲蟲下載站版權所有 京ICP備2021023401號-1
