-
This application note covers the design considerations of a system using the performance
features of the LogiCORE™ IP Advanced eXtensible Interface (AXI) Interconnect core. The
design focuses on high system throughput through the AXI Interconnect core with F
MAX
and
area optimizations in certain portions of the design.
The design uses five AXI video direct memory access (VDMA) engines to simultaneously move
10 streams (five transmit video streams and five receive video streams), each in 1920 x 1080p
format, 60 Hz refresh rate, and up to 32 data bits per pixel. Each VDMA is driven from a video
test pattern generator (TPG) with a video timing controller (VTC) block to set up the necessary
video timing signals. Data read by each AXI VDMA is sent to a common on-screen display
(OSD) core capable of multiplexing or overlaying multiple video streams to a single output video
stream. The output of the OSD core drives the DVI video display interface on the board.
Performance monitor blocks are added to capture performance data. All 10 video streams
moved by the AXI VDMA blocks are buffered through a shared DDR3 SDRAM memory and are
controlled by a MicroBlaze™ processor.
The reference system is targeted for the Virtex-6 XC6VLX240TFF1156-1 FPGA on the
Xilinx® ML605 Rev D evaluation board
標簽：
XAPP
740
AXI
互聯
上傳時間：
2013-11-14
上傳用戶：fdmpy
-
1 Communication Protocol (Computer as master)
The communication protocol describes here allows your computer to access 4096 internal registers (W0000-W4095) and 1024 internal relays (B0000-B1023) in the Workstation..
1.1 Request Message Format
Request message is a command message to be sent from the computer to the Workstation. The data structure of request message is shown below. Note that numbers are always in hexadecimal form and converted into ASCII characters. For example, Workstation unit number 14 will appear in the message as character 0(30h) followed by character E(45h); a BCC of 5Ah will appear in the message as character 5(35h) followed by character A(41h).
標簽：
HITECH
電腦
通信協議
上傳時間：
2013-10-28
上傳用戶：cxl274287265
-
附件是一款PCB阻抗匹配計算工具，點擊CITS25.exe直接打開使用，無需安裝。附件還帶有PCB連板的一些計算方法，連板的排法和PCB聯板的設計驗驗。
PCB設計的經驗建議:
1.一般連板長寬比率為1：1~2.5：1,同時注意For FuJi Machine:a.最大進板尺寸為:450*350mm,
2.針對有金手指的部分,板邊處需作掏空處理,建議不作為連板的部位.
3.連板方向以同一方向為優先,考量對稱防呆,特殊情況另作處理.
4.連板掏空長度超過板長度的1/2時,需加補強邊.
5.陰陽板的設計需作特殊考量.
6.工藝邊需根據實際需要作設計調整,軌道邊一般不少於6mm,實際中需考量板邊零件的排布,軌道設備正常卡壓距離為不少於3mm,及符合實際要求下的連板經濟性.
7.FIDUCIAL MARK或稱光學定位點,一般設計在對角處,為2個或4個,同時MARK點面需平整,無氧化,脫落現象;定位孔設計在板邊,為對稱設計,一般為4個,直徑為3mm,公差為±0.01inch.
8.V-cut深度需根據連板大小及基板板厚考量,角度建議為不少於45°.
9.連板設計的同時,需基於基板的分板方式考量<人工(治具)還是使用分板設備>.
10.使用針孔(郵票孔)聯接：需請考慮斷裂后的毛刺,及是否影響COB工序的Bonding機上的夾具穩定工作,還應考慮是否有無影響插件過軌道,及是否影響裝配組裝.
標簽：
PCB
阻抗匹配
計算工具
教程
上傳時間：
2014-12-31
上傳用戶：sunshine1402
-
附件是一款PCB阻抗匹配計算工具，點擊CITS25.exe直接打開使用，無需安裝。附件還帶有PCB連板的一些計算方法，連板的排法和PCB聯板的設計驗驗。
PCB設計的經驗建議:
1.一般連板長寬比率為1：1~2.5：1,同時注意For FuJi Machine:a.最大進板尺寸為:450*350mm,
2.針對有金手指的部分,板邊處需作掏空處理,建議不作為連板的部位.
3.連板方向以同一方向為優先,考量對稱防呆,特殊情況另作處理.
4.連板掏空長度超過板長度的1/2時,需加補強邊.
5.陰陽板的設計需作特殊考量.
6.工藝邊需根據實際需要作設計調整,軌道邊一般不少於6mm,實際中需考量板邊零件的排布,軌道設備正常卡壓距離為不少於3mm,及符合實際要求下的連板經濟性.
7.FIDUCIAL MARK或稱光學定位點,一般設計在對角處,為2個或4個,同時MARK點面需平整,無氧化,脫落現象;定位孔設計在板邊,為對稱設計,一般為4個,直徑為3mm,公差為±0.01inch.
8.V-cut深度需根據連板大小及基板板厚考量,角度建議為不少於45°.
9.連板設計的同時,需基於基板的分板方式考量<人工(治具)還是使用分板設備>.
10.使用針孔(郵票孔)聯接：需請考慮斷裂后的毛刺,及是否影響COB工序的Bonding機上的夾具穩定工作,還應考慮是否有無影響插件過軌道,及是否影響裝配組裝.
標簽：
PCB
阻抗匹配
計算工具
教程
上傳時間：
2013-10-15
上傳用戶：3294322651
-
This application note covers the design considerations of a system using the performance
features of the LogiCORE™ IP Advanced eXtensible Interface (AXI) Interconnect core. The
design focuses on high system throughput through the AXI Interconnect core with F
MAX
and
area optimizations in certain portions of the design.
The design uses five AXI video direct memory access (VDMA) engines to simultaneously move
10 streams (five transmit video streams and five receive video streams), each in 1920 x 1080p
format, 60 Hz refresh rate, and up to 32 data bits per pixel. Each VDMA is driven from a video
test pattern generator (TPG) with a video timing controller (VTC) block to set up the necessary
video timing signals. Data read by each AXI VDMA is sent to a common on-screen display
(OSD) core capable of multiplexing or overlaying multiple video streams to a single output video
stream. The output of the OSD core drives the DVI video display interface on the board.
Performance monitor blocks are added to capture performance data. All 10 video streams
moved by the AXI VDMA blocks are buffered through a shared DDR3 SDRAM memory and are
controlled by a MicroBlaze™ processor.
The reference system is targeted for the Virtex-6 XC6VLX240TFF1156-1 FPGA on the
Xilinx® ML605 Rev D evaluation board
標簽：
XAPP
740
AXI
互聯
上傳時間：
2013-11-23
上傳用戶：shen_dafa
-
PCB Layout Rule Rev1.70, 規範內容如附件所示, 其中分為:
(1) ”PCB LAYOUT 基本規範”:為R&D Layout時必須遵守的事項, 否則SMT,DIP,裁板時無法生產.
(2) “錫偷LAYOUT RULE建議規範”: 加適合的錫偷可降低短路及錫球.
(3) “PCB LAYOUT 建議規範”:為製造單位為提高量產良率,建議R&D在design階段即加入PCB Layout.
(4) ”零件選用建議規範”: Connector零件在未來應用逐漸廣泛, 又是SMT生產時是偏移及置件不良的主因,故製造希望R&D及採購在購買異形零件時能顧慮製造的需求, 提高自動置件的比例.
標簽：
LAYOUT
PCB
設計規范
上傳時間：
2013-11-03
上傳用戶：tzl1975
-
There are many manufacturers of dot matrix LCD modules. However, most of these displaysare similar. They all have on-board controllers and drivers capable of displaying alpha numericsand a wide variety of other symbols (including Japanese "Katakana" characters). The internaloperation of LCD controller devices is determined by signals sent from a central processing unit(in this case, a CoolRunner-II CPLD).
標簽：
CoolRunner-II
XAPP
904
LCD
上傳時間：
2013-12-17
上傳用戶：haiya2000
-
Debussy是NOVAS Software, Inc(思源科技)發展的HDL Debug & Analysis tool，這套軟體主要不是用來跑模擬或看波形，它最強大的功能是：能夠在HDL source code、schematic diagram、waveform、state bubble diagram之間，即時做trace，協助工程師debug。
可能您會覺的：只要有simulator如ModelSim就可以做debug了，我何必再學這套軟體呢? 其實Debussy v5.0以後的新版本，還提供了nLint -- check coding style & synthesizable，這蠻有用的，可以協助工程師了解如何寫好coding style，並養成習慣。
下圖所示為整個Debussy的原理架構，可歸納幾個結論：
標簽：
Analysis
Software
Debussy
Debug
上傳時間：
2014-01-14
上傳用戶：hustfanenze
-
dvbsnoop is a DVB/MPEG stream analyzer program.
The program can be used to sniff, monitor, debug, dump
or view DVB/MPEG/DSM-CC/MHP stream information (digital
television or data broadcasts) sent via satellite, cable
or terrestrial.
標簽：
program
dvbsnoop
analyzer
monitor
上傳時間：
2013-12-14
上傳用戶：zhangyi99104144
-
The touch screen driver reads input from touch screen hardware and converts it to touch events that are sent to the input system. The driver is also responsible for converting uncalibrated coordinates
標簽：
touch
screen
converts
hardware
上傳時間：
2014-01-17
上傳用戶：大三三
