亚洲xxx大片,国产精品欧美在线观看,亚洲激情精品

serial-port

基于PIC18F1320微控制器的信號采集系統

　　便攜式信號采集在機器健康診斷系統中有較高的應用價值。機器健康診斷的信號特點是包括低頻信號。本文研究是為了實現簡易而且低成本的低頻便攜式信號采集。以Microchip公司單片機PIC18F1320為核心設計信號采集電路，實現了信號的采集和保存。系統采用串行電可擦除芯片24LC32A保存數據，經過有線通信，信號數據由串行口通過MAX232芯片輸送到微型計算機接收和保存，最后繪制出信號波形。微型計算機程序采用Visual Basic編程。研究成功采樣頻率為3 kHz的復雜信號，證明該方案符合設計要求。　　Abstract: 　　Portable signal acquisition is useful in machine health monitoring systems. The signal characteristics of machine health monitoring includes low frequency signals. The goal of this study is to realize simple, inexpensive and portable low frequency signal sampling. This paper provides the project of signal acquisition system design based on PIC18F1320 microcontroller manufactured by the Microchip Technology Incorporation to achieve signal sampling and storage. The system adopted EEPROM 24LC32A to store the signal data. The microcomputer received data via wired link with the MAX232 IC through the serial port. The microcomputer program, programmed in Visual Basic, received the data, stored it and plotted the signal. The study successfully samples 3kHz complicated signals and thus meets the design requirement.

標簽： F1320 1320 PIC 18F

上傳時間： 2013-11-19

上傳用戶：moerwang
基于C8051F020的通用串口適配器的設計

介紹了基于單片機C8051F020的通用串口適配器的設計與實現方法，即由單片機控制的智能化一對多口收發信號轉換器。通過采用C51對單片機進行編程，控制與RS-232（標準RS-232電平）、RS232(TTL電平)、RS-422接口的數據通信；采用C++ Builder作為開發平臺，通過RS-232接口實現上位機對適配器各個通信端口的控制。 Abstract: Design and realization of a universal serial port adapter based on the MCU C8051F020 are introduced.The adapter is an intelligent one-to-more receiving and transmitting signal converter controlled by the MCU. By programming the MCU with the language C51,MCU control data communication between the MCU and RS-232(RS-232 level),RS-232(TTL level),RS-422 port; Using C++ Builder as the development plane, by one RS232 port, the upper PC can control each of the communication port of the adapter.

標簽： C8051F020 串口適配器

上傳時間： 2013-11-19

上傳用戶：hebanlian
用戶程序示例教程

用戶程序示例教程 The Blinky project is a simple program for the LPC2138using Keil MCB2130 Microcontroller Board. It blinks the LEDs at speed according to the Potentiometer setting and prints the current seting to the Serial Port 1.In addition it generates a sine wave with an adjustable frequency on the speaker of the board.

標簽： 用戶教程程序

上傳時間： 2014-12-27

上傳用戶：hongmo
3-V TO 5.5-V MULTICHANNEL RS-2

The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, Contact Discharge)protection on serial-port connection pins. The device meets the requirements of TIA/EIA-232-F and provides theelectrical interface between an asynchronous communication controller and the serial-port connector. Thiscombination of drivers and receivers matches that needed for the typical serial port used in an IBM PC/AT, orcompatible. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-Vsupply. In addition, the device includes an always-active noninverting output (ROUT2B), which allowsapplications using the ring indicator to transmit data while the device is powered down. The device operates atdata signaling rates up to 250 kbit/s and a maximum of 30-V/ms driver output slew rate.

標簽： MULTICHANNEL 5.5 TO RS

上傳時間： 2013-10-19

上傳用戶：ddddddd
基于LabVIEW和單片機的空調溫度場測量系統的研究

基于LabVIEW和單片機的空調溫度場測量系統的研究:室內溫度是空調系統舒適性的重要指標,對其及時、準確地測量顯得非常重要。介紹單片機AT89C51 和數字式、單總線型溫度傳感器DS18B20 組成矩形測量網絡采集空調室內40 點溫度,LabVIEW作為開發平臺,二者之間通過串口實現數據通信,利用LabVIEW強大的數據處理和顯示功能對采集的空調溫度場數據進行實時處理、分析和顯示,詳細介紹了系統的硬件結構和軟件模塊的設計方案。關鍵詞:單片機;DS18B20 ;LabVIEW;串行通信 Abstract : Temperature is a very important criterion of air condition system′s comfort , so it is very significant to measure it accurately and real timely. This paper int roduces a data acquisition system of measuring 40 point s temperature for air condition room based on single wire digital sensor DS18B20 and microcont roller AT89C51 which are composed of rectangle measuring meshwork. The data communication between LabVIEW and microcont roller is executed via serial port ,and the temperature field data of air condition room are processed analyzed and displayed on LabVIEW. The hardware and software modules are also given in detail.Keywords : single chip ;DS18B20 ;LabVIEW; serial communication

標簽： LabVIEW 單片機空調溫度場

上傳時間： 2014-05-05

上傳用戶：KSLYZ
基于PIC單片機的低功耗讀卡器硬件設計

基于PIC單片機的低功耗讀卡器硬件設計:本文提出了一個完整的基于串口的智能讀卡器子系統設計方案并將其實現。讀卡器的設計突出了小型化的要求，全部器件使用貼片封裝。為了減小讀卡器的體積，設計中還使用了串口竊電的技術，使用串口信號線直接給讀卡器供電。為此，讀卡器使用了省電的設計，采用了省電的集成電路，并大膽簡化了許多傳統的設計電路。關鍵字：讀卡器，單片機，串口竊電 Abstract： This paper aims to put forward a complete design of Smart IC card reader based onSerial Port and propose the way of realizing it for the purpose of Network Security. SMD isadopted to make Smart IC reader smaller in this design. To reduce the volume of Smart ICreader， Serial Port powered technology is employed to get power from the signal line of Serial Port. For this reason， low-power consumption components are adopted in the design and some traditional designs are simplified to reduce the power consumption.Keywords： Card Reader； Single-chip Computer； Serial Port Powered IC 卡系統保存了加密算法所需要的工作密鑰，供加密算法對網絡上傳輸的數據加密使用，是整個系統網絡安全的核心。在IC 卡子系統中，讀卡器是一個重要的部分。它起著管理IC卡、在IC 卡和PC或網絡計算機間傳遞數據的重要作用。本文以一片PIC單片機為核心完成了基于RS232 串口的讀卡器的硬件設計。

標簽： PIC 單片機低功耗讀卡器

上傳時間： 2014-04-14

上傳用戶：wanghui2438
LPC1300系列產品勘誤數據手冊

On the LPC13xx, programming, erasure and re-programming of the on-chip flash can be performed using In-System Programming (ISP) via the UART serial port, and also, can be performed using In-Application Programming (IAP) calls directed by the end-user code. For In-System Programming (ISP) via the UART serial port, the ISP command handler (resides in the bootloader) allows erasure of one or more sector (s) of the on-chip flash memory.

標簽： 1300 LPC 勘誤數據手冊

上傳時間： 2013-12-13

上傳用戶：lmq0059
Virtual Serial Port Driver 6.9(虛擬串口)

虛擬串口軟件

標簽： Virtual Serial Driver Port

上傳時間： 2013-10-27

上傳用戶：1234321@q
Virtual Serial Port Driver 6.9(虛擬串口)

虛擬串口軟件

標簽： Virtual Serial Driver Port

上傳時間： 2013-10-23

上傳用戶：JIUSHICHEN
S3C44BOX的BIOS。可使用的命令：help --- show help ? --- = help date --- show or set current date time --

S3C44BOX的BIOS。可使用的命令：help --- show help ? --- = help date --- show or set current date time --- show or set current time setweek --- set weekday clock --- show system running clock setmclk --- set system running clock setbaud ------ set baud rate ipcfg ------ show or set IP address load ------ load file to ram comload ------ load file from serial port run ------ run from sdram prog ------ program flash copy ------ copy flash from src to dst address boot ------ boot from flash backup ------ move bios to the top of flash md ------ show memory data move ------ move program from flash to sdram

標簽： help date show current

上傳時間： 2015-01-22

上傳用戶：ANRAN