The main oscillator allows either a crystal or single-ended input clock signal. Cost-sensitiveapplications typically use an external crystal with the on-chip oscillator circuit since it is the mostcost-effective solution. It is also possible to use the internal oscillator to clock the device after theboot process has completed.
The CAT9555 is a CMOS device that provides 16-bitparallel input/output port expansion for I²C and SMBuscompatible applications. These I/O expanders providea simple solution in applications where additional I/Osare needed: sensors, power switches, LEDs,pushbuttons, and fans.
The CAT9534 is an 8-bit parallel input/output portexpander for I²C and SMBus compatible applications.These I/O expanders provide a simple solution inapplications where additional I/Os are needed: sensors,power switches, LEDs, pushbuttons, and fans.The CAT9534 consists of an input port register, anoutput port register, a configuration register, a polarityinversion register and an I²C/SMBus-compatible serialinterface.
基于單DSP的VoIP模擬電話適配器研究與實現:提出和實現了一種新穎的基于單個通用數字信號處理器(DSP)的VoIP模擬電話適配器方案。DSP的I/O和存儲資源非常有限，通常適于運算密集型應用，不適宜控制密集型應用[5]。該系統高效利用單DSP的I/O和片內外存儲器資源，采用μC/OS-II嵌入式實時操作系統，支持SIP和TCP-UDP/IP協議，通過LAN或者寬帶接入，使普通電話機成為Internet終端，實現IP電話。該系統軟硬件結構緊湊高效，運行穩定，成本低，具有廣闊的應用前景。關鍵詞：模擬電話適配器；IP電話；數字信號處理器；μC/OS-II
【Abstract】This paper presents a VoIP ATA solution based on a single digital signal processor (DSP). DSPs are suitable for arithmetic-intensiveapplication and unsuitable for control-intensive application because of the limitation of I/O and memory resources. This solution is based on a 16-bitfixed-point DSP and μC/OS-II embedded real-time operating system. It makes good use of the limited resources, supports SIP and TCP-UDP/IPprotocol. It can connect the analog telephone to Internet and realize the VoIP application. This system has a great future for its high efficiency andlow cost.【Key words】Analog telephone adapter (ATA); Voice over Internet protocol (VoIP); Digital signal processor (DSP); μC/OS-II
Research and Implementation of VoIPATA Based on Single DSP
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using SW routines implemented in C. The code is focused onthe SAB C513, but will fit to all C500 derivatives.Beyond the low level software drivers a test shell is delivered. This shell allows a quicktest of the software drivers by an emulator or a starter kit demo board.
The AT89C52 is a low-power, high-performance CMOS 8-bit microcomputer with 8Kbytes of Flash programmable and erasable read only memory (PEROM). The deviceis manufactured using Atmel’s high-density nonvolatile memory technology and iscompatible with the industry-standard 80C51 and 80C52 instruction set and pinout.The on-chip Flash allows the program memory to be reprogrammed in-system or by aconventional nonvolatile memory programmer. By combining a versatile 8-bit CPUwith Flash on a monolithic chip, the Atmel AT89C52 is a powerful microcomputerwhich provides a highly-flexible and cost-effective solution to many embedded controlapplications.
Abstract: This application note discusses the development and deployment of 3G cellular femtocell base stations. The technicalchallenges for last-mile residential connectivity and adding system capacity in dense urban environments are discussed, with 3Gfemtocell base stations as a cost-effective solution. Maxim's 3GPP TS25.104-compliant transceiver solution is presented along withcomplete radio reference designs such as RD2550. For more information on the RD2550, see reference design 5364, "FemtocellRadio Reference Designs Using the MAX2550–MAX2553 Transceivers."
6小時學會labview,
labview Six Hour Course – Instructor Notes
This zip file contains material designed to give students a working knowledge of labview in a 6 hour timeframe. The contents are:
Instructor Notes.doc – this document.
labviewIntroduction-SixHour.ppt – a PowerPoint presentation containing screenshots and notes on the topics covered by the course.
Convert C to F (Ex1).vi – Exercise 1 solution VI.
Convert C to F (Ex2).vi – Exercise 2 solution subVI.
Thermometer-DAQ (Ex2).vi – Exercise 2 solution VI.
Temperature Monitor (Ex3).vi – Exercise 3 solution VI.
Thermometer (Ex4).vi – Exercise 4 solution subVI.
Convert C to F (Ex4).vi – Exercise 4 solution subVI.
Temperature Logger (Ex4).vi – Exercise 4 solution VI.
Multiplot Graph (Ex5).vi – Exercise 5 solution VI.
Square Root (Ex6).vi – Exercise 6 solution VI.
State Machine 1 (Ex7).vi – Exercise 7 solution VI.
The slides can be presented in two three hour labs, or six one hour lectures. Depending on the time and resources available in class, you can choose whether to assign the exercises as homework or to be done in class. If you decide to assign the exercises in class, it is best to assign them in order with the presentation. This way the students can create VI’s while the relevant information is still fresh. The notes associated with the exercise slide should be sufficient to guide the students to a solution. The solution files included are one possible solution, but by no means the only solution.
Abstract: High-speed and low-speed data converters serve critical functions in modern broadband mobile radios. This application note outlines how todetermine high-speed data converter performance requirements in baseband sampling radio architectures. Also, system partition strategies andadvantages are outlined when considering a high-speed analog front-end (AFE) solution.
