-
The LTC®1966 is a true RMS-to-DC converter that uses aDS computational technique to make it dramatically simplerto use, significantly more accurate, lower in powerconsumption and more flexible than conventional logantilogRMS-to-DC converters. The LTC1966 RMS-to-DCconverter has an input signal range from 5mVRMS to1.5VRMS (a 50dB dynamic range with a single 5V supplyrail) and a 3dB bandwidth of 800kHz with signal crestfactors up to four.
標簽：
真有效值
轉換器
自動調節
上傳時間：
2013-10-12
上傳用戶：qilin
-
High input impedance and a wide input range are twohighly desirable features in a precision analog-to-digitalconverter, and the LTC®2449 delta-sigma ADC has both.With just a few external components, the LTC2449 formsan exceptional measurement system with very high inputimpedance and an input range that extends 300mV beyondthe supply rails.
標簽：
ADC
精密測量
高輸入阻抗
上傳時間：
2013-11-02
上傳用戶：ywcftc277
-
Digital-to-analog converters (DACs) are prevalent inindustrial control and automated test applications.General-purpose automated test equipment often requiresmany channels of precisely controlled voltagesthat span several voltage ranges. The LTC2704 is ahighly integrated 16-bit, 4-channel DAC for high-endapplications. It has a wide range of features designed toincrease performance and simplify design.
標簽：
DAC
集成
四通道
工業
上傳時間：
2013-11-22
上傳用戶：元宵漢堡包
-
Designers of signal receiver systems often need to performcascaded chain analysis of system performancefrom the antenna all the way to the ADC. Noise is a criticalparameter in the chain analysis because it limits theoverall sensitivity of the receiver. An application’s noiserequirement has a signifi cant infl uence on the systemtopology, since the choice of topology strives to optimizethe overall signal-to-noise ratio, dynamic range andseveral other parameters. One problem in noise calculationsis translating between the various units used by thecomponents in the chain: namely the RF, IF/baseband,and digital (ADC) sections of the circuit.
標簽：
數字接收器
信號鏈
噪聲分析
上傳時間：
2014-12-05
上傳用戶：cylnpy
-
Portable, battery-powered operation of electronic apparatushas become increasingly desirable. Medical, remotedata acquisition, power monitoring and other applicationsare good candidates for battery operation. In some circumstances,due to space, power or reliability considerations,it is preferable to operate the circuitry from a single 1.5Vcell. Unfortunately, a 1.5V supply eliminates almost alllinear ICs as design candidates. In fact, the LM10 opamp-reference and the LT®1017/LT1018 comparators arethe only IC gain blocks fully specifi ed for 1.5V operation.Further complications are presented by the 600mV dropof silicon transistors and diodes. This limitation consumesa substantial portion of available supply range, makingcircuit design diffi cult. Additionally, any circuit designedfor 1.5V operation must function at end-of-life batteryvoltage, typically 1.3V. (See Box Section, “Componentsfor 1.5V Operation.”)
標簽：
Circuitry
Operation
Single
1017
上傳時間：
2013-12-20
上傳用戶：Wwill
-
Radio Frequency Integrated Circuit Design
I enjoyed reading this book for a number of reasons. One reason is that itaddresses high-speed analog design in the context of microwave issues. This isan advanced-level book, which should follow courses in basic circuits andtransmission lines. Most analog integrated circuit designers in the past workedon applications at low enough frequency that microwave issues did not arise.As a consequence, they were adept at lumped parameter circuits and often notcomfortable with circuits where waves travel in space. However, in order todesign radio frequency (RF) communications integrated circuits (IC) in thegigahertz range, one must deal with transmission lines at chip interfaces andwhere interconnections on chip are far apart. Also, impedance matching isaddressed, which is a topic that arises most often in microwave circuits. In mycareer, there has been a gap in comprehension between analog low-frequencydesigners and microwave designers. Often, similar issues were dealt with in twodifferent languages. Although this book is more firmly based in lumped-elementanalog circuit design, it is nice to see that microwave knowledge is brought inwhere necessary.Too many analog circuit books in the past have concentrated first on thecircuit side rather than on basic theory behind their application in communications.The circuits usually used have evolved through experience, without asatisfying intellectual theme in describing them. Why a given circuit works bestcan be subtle, and often these circuits are chosen only through experience. Forthis reason, I am happy that the book begins first with topics that require anintellectual approach—noise, linearity and filtering, and technology issues. Iam particularly happy with how linearity is introduced (power series). In therest of the book it is then shown, with specific circuits and numerical examples,how linearity and noise issues arise.
標簽：
Rogers
Radio
John
Freq
上傳時間：
2014-12-23
上傳用戶：han_zh
-
Abstract: This application note illustrates an intermediate 8V switching power supply for an automotive radio and infotainment system.The design withstands the complete automotive input voltage range (including cold crank and load dump conditions), assuring a stable8V supply for common subsystems such as a CD driver, LCDs, and a radio module in modern infotainment systems. To avoiddisturbance in the AM and FM bands, the switching power supply runs at a fixed frequency of 2MHz, enabling an ideal solution forradio systems.
標簽：
汽車無線電
信息娛樂系統
開關電源
上傳時間：
2013-11-20
上傳用戶：feitian920
-
Abstract: This document details the Lakewood (MAXREFDES7#) subsystem reference design, a 3.3V input, ±12V (±15V) output, isolated power supply. The Lakewood reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and two wide input range and adjustable output low-dropout linear regulators (LDOs). Test results and hardware files are included.
標簽：
MAXREFDES
Lakewood
Isolated
Output
上傳時間：
2013-11-02
上傳用戶：fengzimili
-
Abstract: This document details the Riverside (MAXREFDES8#) subsystem reference design, a 3.3V input, 12V (15V) output, isolated power supply. The Riverside reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and one wide input range and adjustable output low-dropout linear regulator (LDO). Test results and hardware files are included.
標簽：
Riverside
MAXREFDES
Isolated
Output
上傳時間：
2013-11-16
上傳用戶：會稽劍客
-
Abstract: This document details the Oceanside (MAXREFDES9#) subsystem reference design, a 3.3V to 15V input,±15V (±12V) output, isolated power supply. The Oceanside design includes a high-efficiency step-up controller, a36V H-bridge transformer driver for isolated supplies, a wide input range, and adjustable output low-dropout linearregulator (LDO). Test results and hardware files are included.
標簽：
隔離電源
設計手冊
上傳時間：
2013-10-12
上傳用戶：jinyao
