The MSP-FET430PIF is a Parallel Port interface (does not include target board) that is used to program and debug MSP430 FET tools and test boards through the JTAG interface. This interface is included in our FET tools, but sold without the development board. This interface uses a Parallel PC Port to communicate to the Debugger Software (IAR Kickstart software included) running on the PC. The interface uses the standard 14 pin header to communicate to the MSP430 device using the standard JTAG protocol.
The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is extremely low power, no external power supply is required. The tool has an integrated software environment and connects directly to the PC which greatly simplifies the set-up and use of the tool. The flash development tool supports development with all MSP430 flash parts.
Features
MSP430 debugging interface to connect a MSP430-Flash-device to a Parallel port on a PC
Supports JTAG debug protocol (NO support for Spy-Bi-Wire (2-wire JTAG) debug protocol, Spy-Bi-Wire (2-wire JTAG) is supported by MSP-FET430UIF)
Parallel Port cable and a 14-conductor target cable
Full documentation on CD ROM
Integrated IAR Kickstart user interface which includes:
Assembler
Linker
Limulator
Source-level debugger
Limited C-compiler
Technical specifications:
Backwardly compatable with existing FET tool boards.
What is New in C51 Version 8.18[Device Support]Added debug support for the NXP P89LPC9408 in the LPC900 EPM Emulator/Programmer.[New supported Device]Nuvoton W681308 device.[New supported Device]NXP P89LPC9201, P89LPC9211, P89LPC922A1, P89LPC9241, P89LPC9251, P89LPC9301, P89LPC931A1, P89LPC9331, P89LPC9341, and P89LPC9351 devices.[New supported Device]SiLabs C8051F500, C8051F501, C8051F504, C8051F505, C8051F506, C8051F507, C8051F508, C8051F509, C8051F510, and C8051F511 devices.[ULINK2 Support]Corrected potential deadlock on ST uPSD targets.[Device Simulation]Corrected simulation of Infineon XC800 MDU.[Device Simulation]Corrected behaviour of EXFn and TOGn on SiLabs C8051F12x/F13x devices.[Device Simulation]Added simulation for Atmel AT89C51RE2, including simulation of second UART.[Cx51 Compiler]Corrected failed initialization on far addresses when the object is located with _at_.
本資料僅供學習評估之用,請勿用于商業用途!請?jiān)趯W(xué)習評估24小時內刪除.
MPLAB C30用戶指南(英文)
HIGHLIGHTSThe information covered in this chapter is as follows:• About this Guide• Recommended Reading• Troubleshooting• The Microchip Web Site• Development Systems Customer Notification Service• Customer Support
Document LayoutThe document layout is as follows:• Chapter 1: Compiler Overview – describes MPLAB C30, development tools andfeature set.• Chapter 2: Differences between MPLAB C30 and ANSI C – describes thedifferences between the C language supported by MPLAB C30 syntax and thestandard ANSI-89 C.• Chapter 3: Using MPLAB C30 – describes how to use the MPLAB C30 compilerfrom the command line.• Chapter 4: MPLAB C30 Runtime Environment – describes the MPLAB C30runtime model, including information on sections, initialization, memory models, thesoftware stack and much more.• Chapter 5: Data Types – describes MPLAB C30 integer, floating point and pointerdata types.• Chapter 6: Device Support Files – describes the MPLAB C30 header and registerdefinition files, as well as how to use with SFR’s.• Chapter 7: Interrupts – describes how to use interrupts.• Chapter 8: Mixing Assembly Language and C Modules – provides guidelines tousing MPLAB C30 with MPLAB ASM30 assembly language modules.
FeaturesThe following standard features are provided.• Choice of RTOS scheduling policy1. Pre-emptive:Always runs the highest available task. Tasks of identical priorityshare CPU time (fully pre-emptive with round robin time slicing).2. Cooperative:Context switches only occur if a task blocks, or explicitly callstaskYIELD().• Co-routines (light weight tasks that utilise very little RAM).• Message queues• Semaphores [via macros]• Trace visualisation ability (requires more RAM)• Majority of source code common to all supported development tools• Wide range of ports and examples
This application note describes how to implement the Bus LVDS (BLVDS) interface in the supported Altera ® device families for high-performance multipoint applications. This application note also shows the performance analysis of a multipoint application with the Cyclone III BLVDS example.
This application note explains the XC9500™/XL/XV Boundary Scan interface anddemonstrates the software available for programming and testing XC9500/XL/XV CPLDs. Anappendix summarizes the iMPACT software operations and provides an overview of theadditional operations supported by XC9500/XL/XV CPLDs for in-system programming.
This application note describes how to implement the Bus LVDS (BLVDS) interface in the supported Altera ® device families for high-performance multipoint applications. This application note also shows the performance analysis of a multipoint application with the Cyclone III BLVDS example.
This application note explains the XC9500™/XL/XV Boundary Scan interface anddemonstrates the software available for programming and testing XC9500/XL/XV CPLDs. Anappendix summarizes the iMPACT software operations and provides an overview of theadditional operations supported by XC9500/XL/XV CPLDs for in-system programming.
This simple SDI Notepad-like application demonstrates how, taking advantage of the MFC support for Unicode, to Turkmenize labels of the specified menu items. Actually, Turkmen is not supported by Windows 2000, therefore, to create such resources as menu so that strings in Turkmen could be displayed I had to invent an additional technique 這是一個與記事本類似的簡單的SDI應用程序，演示了怎樣使用MFC來支持 Unicode，對指定的菜單條目進行Turkmenize標簽化。實際上，Windwos 2000并不支持Turknen,因此,創建了那些菜單資源以便那些字符串可以在Turknen中顯示,為此我必須開發其它的技術。 來源: http://www.codeguru.com/advancedui/SDI_Note.html
