在需要實時大量輸入漢字的顯示控制處理應用中，利用傳統單片機實現顯示控制的設計方法是較難實現的。帶漢字字庫的液晶模塊的使用使得小容量ROM單片機的大量漢字信息輸入與顯示成為可能。提出了針對漢字字庫編碼的二級索引拼音輸入檢索方法,介紹了以ST7920作為控制器的帶漢字字庫的液晶顯示模塊的接口方法及漢字顯示和控制原理，給出了通用計算機鍵盤在單片機中的串行接口，采用該技術可大大增強單片機的漢字輸入功能。為小容量ROM單片機的大批量漢字信息處理提供了一種漢字輸入解決方案。
Abstract:
It is difficult to realize Chinese characters input method based on the embedded system by using the traditional design method of display control. It is possible to input and display Chinese characters based on the embedded system with the ROM of small content by using the LCD module with Chinese characters.Chinese characters input method of the quadric index recall in allusion to Chinese characters code is brought forward.The interface and the principle of Chinese characters display control based on the LCD module controlled with the ST7920 is introduced too.The serial interface of the computer keyboard in common use and the embedded system is given at the same time. It can enhance the embedded system function of Chinese characters input by using this technology, and provide a kind of Chinese characters input scheme for the embedded system with small capacity ROM.
Important Notice SUNPLUS INNOVATION technology INC. reserves the right to change this documentation without prior notice. Information provided by SUNPLUS INNOVATION technology INC. is believed to be accurate and reliable. However, SUNPLUS INNOVATION technology INC.makes no warranty for any errors which may appear in this document. Contact SUNPLUS INNOVATION technology INC.to obtain the latest version of device specifications before placing your order. No responsibility is assumed by SUNPLUS INNOVATION technology INC. for any infringement of patent or other rights of third parties which may result from its use. In addition, SUNPLUSIT products are not authorized for use as critical components in life support systems or aviation systems, where a malfunction or failure of the product may reasonably be expected to result in significant injury to the user, without the express written approval of SunplusIT
Although Stellaris microcontrollers have generous internal SRAM capabilities, certain applicationsmay have data storage requirements that exceed the 8 KB limit of the Stellaris LM3S8xx seriesdevices. Since microcontrollers do not have an external parallel data-bus, serial memory optionsmust be considered. Until recently, the ubiquitous serial EEPROM/flash device was the only serialmemory solution. The major limitations of EEPROM and flash technology are slow write speed, slowerase times, and limited write/erase endurance.Recently, serial SRAM devices have become available as a solution for high-speed dataapplications. The N256S08xxHDA series of devices, from AMI Semiconductor, offer 32 K x 8 bits oflow-power data storage, a fast Serial Peripheral Interface (SPI) serial bus, and unlimited write cycles.The parts are available in 8-pin SOIC and compact TSSOP packages.
本文依據集成電路設計方法學，探討了一種基于標準Intel 8086 微處理器的單芯片計算機平臺的架構。研究了其與SDRAM，8255 并行接口等外圍IP 的集成，并在對AMBA協議和8086 CPU分析的基礎上，采用遵從AMBA傳輸協議的系統總線代替傳統的8086 CPU三總線結構，搭建了基于8086 IP 軟核的單芯片計算機系統，并實現了FPGA 功能演示。關鍵詞：微處理器； SoC；單芯片計算機；AMBA 協議
Design of 8086 CPU Based Computer-on-a-chip System（School of Electrical Engineering and Automation, Heifei University of technology, Hefei, 230009,China）Abstract: According to the IC design methodology, this paper discusses the design of one kind of Computer-on-a-chip system architecture, which is based on the standard Intel8086 microprocessor,investigates how to integrate the 8086 CPU and peripheral IP such as, SDRAM controller, 8255 PPI etc. Based on the analysis of the standard Intel8086 microprocessor and AMBA Specification,the Computer-on-a-chip system based on 8086 CPU which uses AMBA bus instead of traditional three-bus structure of 8086 CPU is constructed, and the FPGA hardware emulation is fulfilled.Key words: Microprocessor; SoC; Computer-on-a-chip; AMBA Specification
基于PIC單片機的低功耗讀卡器硬件設計:本文提出了一個完整的基于串口的智能讀卡器子系統設計方案并將其實現。讀卡器的設計突出了小型化的要求，全部器件使用貼片封裝。為了減小讀卡器的體積，設計中還使用了串口竊電的技術，使用串口信號線直接給讀卡器供電。為此，讀卡器使用了省電的設計，采用了省電的集成電路，并大膽簡化了許多傳統的設計電路。關鍵字： 讀卡器， 單片機， 串口竊電
Abstract： This paper aims to put forward a complete design of Smart IC card reader based onSerial Port and propose the way of realizing it for the purpose of Network Security. SMD isadopted to make Smart IC reader smaller in this design. To reduce the volume of Smart ICreader， Serial Port powered technology is employed to get power from the signal line of Serial Port. For this reason， low-power consumption components are adopted in the design and some traditional designs are simplified to reduce the power consumption.Keywords： Card Reader； Single-chip Computer； Serial Port Powered
IC 卡系統保存了加密算法所需要的工作密鑰，供加密算法對網絡上傳輸的數據加密使用，是整個系統網絡安全的核心。在IC 卡子系統中，讀卡器是一個重要的部分。它起著管理IC卡、在IC 卡和PC或網絡計算機間傳遞數據的重要作用。本文以一片PIC單片機為核心完成了基于RS232 串口的讀卡器的硬件設計。
CAN與RS232轉換節點的設計與實現
介紹將CAN總線接口與RS232總線接口相互轉換的設計方法和2種總線電平轉換關系，實現CAN總線與各模塊的接口設計，制定了相應的軟硬件設計方案，并給出軟件設計流程圖以及部分硬件設計原理圖。為CAN總線與RS232總線互聯提供了一種方法，對CAN總線與RS232總線接口設備的互聯和廣泛應用的實現具有重要意義。關鍵詞：CAN總線；RS-232總線；串行通信Design and Realization of CAN and RS232 Transformation NodeZHOU Wei, CHENG Xiao-hong(Information Institute, Wuhan University of technology, Wuhan 430070)【Abstract】This paper introduces one design method of the CAN bus interface and the RS232 bus interface interconversion, emphasizes two kindof bus level transformation relations, realizes the CAN bus and various modules connection design, formulates the design proposal of correspondingsoftware and hardware, and gives the flow chart of software design as well as the partial schematic diagram of hardware design. It providesonemethod for the CAN bus and the RS232 bus interconnection, has the vital significance to widespread application realization of the CAN busand theRS232 bus interface equipment interconnection.【Key words】CAN bus; RS-232 bus; serial communication
