The PW4055 is a complete constant-current /constant-voltage linear charger for single cell lithiumion batteries.Its ThinSOT package and low external component count make the PW4055 ideallysuited for portable applications.Furthermore, the PW4055 is specifically designed to work within USBpower specifications.The PW4055 No external sense resistor is needed, and no blocking diode is required due to theinternal MOSFET architecture.Thermal feedback regulates the charge current to limit the dietemperature during high power operation or high ambient temperature. The charge voltage is fixedat 4.2V, and the charge current can be programmed externally with a single resistor. The PW4055automatically terminates the charge cycle when the charge current drops to 1/10th the programmedvalue after the final float voltage is reached. When the input supply (wall adapter or USB supply) isremoved, the PW4055 automatically enters a low current state, dropping the battery drain currentto less than 2μA. The PW4055 can be put into shutdown mode, reducing the supply current to 25μA.The BAT pin has a 7KV ESD(HBM) capability. Other features include charge current monitor, undervoltage lockout, automatic recharge and a status pin to indicate charge termination and the presenceof an input voltage
標簽： pw4055
上傳時間： 2022-02-11
上傳用戶：jason_vip1
電子書-RTL Design Style Guide for Verilog HDL540頁A FF having a fixed input value is generated from the description in the upper portion of Example 2-21. In this case, ’0’ is output when the reset signal is asynchronously input, and ’1’ is output when the START signal rises. Therefore, the FF data input is fixed at the power supply, since the typical value ’1’ is output following the rise of the START signal. When FF input values are fixed, the fixed inputs become untestable and the fault detection rate drops. When implementing a scan design and converting to a scan FF, the scan may not be executed properl not be executed properly, so such descriptions , so such descriptions are not are not recommended. recommended.[1] As in the lower part of Example 2-21, be sure to construct a synchronous type of circuit and ensure that the clock signal is input to the clock pin of the FF. Other than the sample shown in Example 2-21, there are situations where for certain control signals, those that had been switched due to the conditions of an external input will no longer need to be switched, leaving only a FF. If logic exists in a lower level and a fixed value is input from an upper level, the input value of the FF may also end up being fixed as the result of optimization with logic synthesis tools. In a situation like this, while perhaps difficult to completely eliminate, the problem should be avoided as much as possible.
標簽： RTL verilog hdl
上傳時間： 2022-03-21
上傳用戶：canderile
首先下載軟件，解壓軟件，安裝在程序中找到SEGGER,選里面的J-FLASH，進入界面，剛開始的那個界面可以忽略，不用建project也可以；單擊菜單欄的“Options---Project settings”打開設置，進行jlink配置;正在General選項，選擇“USB”，一般都是默認配置，確認一下即可;然后在CPU選項，選擇芯片型號，先選擇“Device”才能選擇芯片型號，芯片型號，要根據你使用的芯片進行選擇;在Target interface選項 里面選擇SWD模式;首先Target里面選“Connection”連接目標芯片，然后 Target--Auto進行程序燒寫;首先Target里面選擇“Connection”連接目標芯片，然后 Target--Auto進行程序燒寫.SEGGER J-Links are the most widely used line of debug probes available today. They've proven their value for more than 10 years in embedded development. This popularity stems from the unparalleled performance, extensive feature set, large number of supported CPUs, and compatibility with all popular development environments.
標簽： JLINK
上傳時間： 2022-03-22
上傳用戶：
本文主要介紹如何在Wado設計套件中進行時序約束，原文出自 xilinx中文社區。1 Timing Constraints in Vivado-UCF to xdcVivado軟件相比于sE的一大轉變就是約束文件，5E軟件支持的是UcF（User Constraints file，而 Vivado軟件轉換到了XDc（Xilinx Design Constraints）。XDC主要基于SDc（Synopsys Design Constraints）標準，另外集成了Xinx的一些約束標準可以說這一轉變是xinx向業界標準的靠攏。Altera從 TimeQuest開始就一直使用SDc標準，這一改變，相信對于很多工程師來說是好事，兩個平臺之間的轉換會更加容易些。首先看一下業界標準SDc的原文介紹：Synopsys widely-used design constraints format, known as sDc, describes the design intent"and surrounding constraints for synthesis, clocking, timing, power, test and environmental and operating conditions. sDc has been in use and evolving for more than 20 years, making it the most popular and proven format for describing design constraints. Essentially all synthesized designs use SDc and numerous EDa companies have translators that can read and process sDc
標簽： vivado
上傳時間： 2022-03-26
上傳用戶：
為設計高效率、低損耗的PFC電路,本文基于UCC28019進行電路設計。以UCC28019輸出的PWM波形來控制Boost升壓斬波為核心電路,使電路中的電容交替地充放電、電感交替的儲存和釋放能量,最后實現在輸入AC20V~24V電壓情況下穩定輸出DC38V。測試結果表明,系統實現效率為95%左右,電壓調整率小于1%,電源功率因數0.99。交流輸入電壓為19.0-25.8 V時,輸出直流電壓穩定性較好,電感無明顯嘯叫且紋波小,具有一定的帶負載能力和實用性。In order to design the PFC circuit with high efficiency and low loss,this paper designs the circuit based on UCC28019.The PWM waveform output by UCC28019 is used to control boost chopper as the core circuit,which alternately charges and discharges capacitors,stores and releases energy by inductors,and finally achieves stable output of DC38 V under the input voltage of AC20 V~24 V.The test results show that the system achieves about 95% efficiency,the voltage adjustment rate is less than 1%,the power factor is 0.99,and the AC input voltage is 19.0-25.8 V.The output DC voltage stability is good,the inductance has no obvious whistle and the ripple is small,so it has certain load capacity and practicability.
上傳時間： 2022-04-03
上傳用戶：
This manual documents the Microcontroller profile of version 7 of the ARM? Architecture, the ARMv7-M architecture profile. For short definitions of all the ARMv7 profiles see About the ARMv7 architecture, and architecture profiles on page A1-20.ARMv7 is documented as a set of architecture profiles. The profiles are defined as follows: ARMv7-A The application profile for systems supporting the ARM and Thumb instruction sets, and requiring virtual address support in the memory management model. ARMv7-R The realtime profile for systems supporting the ARM and Thumb instruction sets, and requiring physical address only support in the memory management model ARMv7-M The microcontroller profile for systems supporting only the Thumb instruction set, and where overall size and deterministic operation for an implementation are more important than absolute performance. While profiles were formally introduced with the ARMv7 development, the A-profile and R-profile have implicitly existed in earlier versions, associated with the Virtual Memory System Architecture (VMSA) and Protected Memory System Architecture (PMSA) respectively.
標簽： arm
上傳時間： 2022-06-02
上傳用戶：
German universities and scientists have repeatedly set the intermational standard in drive technology. Identification and active compensation of natural frequencies in oscillatory mechanics, status controls with monitoring structures incorporating acceleration sensors, adaptive compensation of measurement system deficiencies, self-adjusting detent torque compensation… everything invented with only a single aim in mind: to continue improv-ing the motion control, dynamics, precision and processing speed of your machines. For the industrial applicabability of this technology scientific publications in proceedings and laboratory test rigs are not enough. These features consequenty need to be converted into cost-efficient and easily manageable products. That 's exactly what we have done.So in future, if you should need more than today ' smarket can offer you, now everything isgoing to be alright. With our new high-performance ServoOne drive series you will experi-ence
標簽： servoone
上傳時間： 2022-06-24
上傳用戶：kingwide
PrefaceDuring the past years, there has been a quickly rising interest in radio access technologies for providingmobile as well as nomadic and fixed services for voice, video, and data. The difference indesign, implementation, and use between telecom and datacom technologies is also becoming moreblurred. One example is cellular technologies from the telecom world being used for broadband dataand wireless LAN from the datacom world being used for voice-over IP.Today, the most widespread radio access technology for mobile communication is digital cellular,with the number of users passing 5 billion by 2010, which is more than half of the world’s population.It has emerged from early deployments of an expensive voice service for a few car-borne users,to today’s widespread use of mobile-communication devices that provide a range of mobile servicesand often include camera, MP3 player, and PDA functions. With this widespread use and increasinginterest in mobile communication, a continuing evolution ahead is foreseen.This book describes LTE, developed in 3GPP (Third Generation Partnership Project) and providingtrue 4G broadband mobile access, starting from the first version in release 8 and through the continuingevolution to release 10, the latest version of LTE. Release 10, also known as LTE-Advanced,is of particular interest as it is the major technology approved by the ITU as fulfilling the IMTAdvancedrequirements. The description in this book is based on LTE release 10 and thus provides acomplete description of the LTE-Advanced radio access from the bottom up.Chapter 1 gives the background to LTE and its evolution, looking also at the different standardsbodies and organizations involved in the process of defining 4G. It also gives a discussion of the reasonsand driving forces behind the evolution.Chapters 2–6 provide a deeper insight into some of the technologies that are part of LTE and itsevolution. Because of its generic nature, these chapters can be used as a background not only for LTEas described in this book, but also for readers who want to understand the technology behind othersystems, such as WCDMA/HSPA, WiMAX, and CDMA2000.Chapters 7–17 constitute the main part of the book. As a start, an introductory technical overviewof LTE is given, where the most important technology components are introduced based onthe generic technologies described in previous chapters. The following chapters provide a detaileddescription of the protocol structure, the downlink and uplink transmission schemes, and the associatedmechanisms for scheduling, retransmission and interference handling. Broadcast operation andrelaying are also described. This is followed by a discussion of the spectrum flexibility and the associated
上傳時間： 2022-07-08
上傳用戶：
?This is a high sensitivity type of Nicera Hall element using evaporated InSbfilm.?It performs effectively in low magnetic fields due to the high sensitivity.?The input and output resistance values are suitable for transistor circuitsBrushless motors?DVD drive, CD-ROM drive, floppy disk drive?Other small precision motors?Non-contacting magnetic sensors?Position sensors, rotation sensors, current sensors?Magnetic flux sensors other than those above
標簽： nhe520f
上傳時間： 2022-07-26
上傳用戶：
This is a high sensitivity type of Nicera Hall element using evaporated InSbfilm.It performs effectively in low magnetic fields due to the high sensitivity.The input and output resistance values are suitable for transistor circuits.Sip type packageApplications Brushless motorsPosition sensors, rotation sensors, current sensorsNon-contacting magnetic sensorsCurrent sensorsMagnetic flux sensors other than those above
上傳時間： 2022-07-26
上傳用戶：
