Xilinx FPGAs require at least two power supplies: VCCINTfor core circuitry and VCCO for I/O interface. For the latestXilinx FPGAs, including Virtex-II Pro, Virtex-II and Spartan-3, a third auxiliary supply, VCCAUX may be needed. Inmost cases, VCCAUX can share a power supply with VCCO.The core voltages, VCCINT, for most Xilinx FPGAs, rangefrom 1.2V to 2.5V. Some mature products have 3V, 3.3Vor 5V core voltages. Table 1 shows the core voltagerequirement for most of the FPGA device families. TypicalI/O voltages (VCCO) vary from 1.2V to 3.3V. The auxiliaryvoltage VCCAUX is 2.5V for Virtex-II Pro and Spartan-3, andis 3.3V for Virtex-II.
上傳時間： 2013-10-22
上傳用戶：liu999666
This application note covers the design considerations of a system using the performance features of the LogiCORE™ IP Advanced eXtensible Interface (AXI) Interconnect core. The design focuses on high system throughput through the AXI Interconnect core with F MAX and area optimizations in certain portions of the design. The design uses five AXI video direct memory access (VDMA) engines to simultaneously move 10 streams (five transmit video streams and five receive video streams), each in 1920 x 1080p format, 60 Hz refresh rate, and up to 32 data bits per pixel. Each VDMA is driven from a video test pattern generator (TPG) with a video timing controller (VTC) block to set up the necessary video timing signals. Data read by each AXI VDMA is sent to a common on-screen display (OSD) core capable of multiplexing or overlaying multiple video streams to a single output video stream. The output of the OSD core drives the DVI video display interface on the board. Performance monitor blocks are added to capture performance data. All 10 video streams moved by the AXI VDMA blocks are buffered through a shared DDR3 SDRAM memory and are controlled by a MicroBlaze™ processor. The reference system is targeted for the Virtex-6 XC6VLX240TFF1156-1 FPGA on the Xilinx® ML605 Rev D evaluation board
上傳時間： 2013-11-14
上傳用戶：fdmpy
XAPP520將符合2.5V和3.3V I/O標準的7系列FPGA高性能I/O Bank進行連接 The I/Os in Xilinx® 7 series FPGAs are classified as either high range (HR) or high performance (HP) banks. HR I/O banks can be operated from 1.2V to 3.3V, whereas HP I/O banks are optimized for operation between 1.2V and 1.8V. In circumstances that require an HP 1.8V I/O bank to interface with 2.5V or 3.3V logic, a range of options can be deployed. This application note describes methodologies for interfacing 7 series HP I/O banks with 2.5V and 3.3V systems
上傳時間： 2013-11-19
上傳用戶：yyyyyyyyyy
SRAM-based FPGAs are non-volatile devices. Upon powerup, They are required to be programmed from an external source. This procedure allows anyone to easily monitor the bit-stream, and clone the device. The problem then becomes how can you effectively protect your intellectual property from others in an architecture where the part is externally programmed?
上傳時間： 2013-11-06
上傳用戶：wl9454
針對嵌入式機器視覺系統向獨立化、智能化發展的要求，介紹了一種嵌入式視覺系統--智能相機。基于對智能相機體系結構、組成模塊和圖像采集、傳輸和處理技術的分析，對國內外的幾款智能相機進行比較。綜合技術發展現狀，提出基于FPGA+DSP模式的硬件平臺，并提出智能相機的發展方向。分析結果表明，該系統設計可以實現脫離PC運行，完成圖像獲取與分析，并作出相應輸出。 Abstract: This paper introduced an embedded vision system-intelligent camera ，which was for embedded machine vision systems to an independent and intelligent development requirements. Intelligent camera architecture， component modules and image acquisition， transmission and processing technology were analyzed. After comparing integrated technology development of several intelligent cameras at home and abroad， the paper proposed the hardware platform based on FPGA+DSP models and made clear direction of development of intelligent cameras. On the analysis of the design， the results indicate that the system can run from the PC independently to complete the image acquisition and analysis and give a corresponding output.
上傳時間： 2013-10-24
上傳用戶：bvdragon
The LogiCORE™ GTP Wizard automates the task of creating HDL wrappers to configure the high-speed serial GTP transceivers in Virtex™-5 LXT and SXT devices. The menu-driven interface allows one or more GTP transceivers to be configured using pre-definedtemplates for popular industry standards, or from scratch, to support a wide variety of custom protocols.The Wizard produces a wrapper, an example design, and a testbench for rapid integration and verification of the serial interface with your custom function Features• Creates customized HDL wrappers to configureVirtex-5 RocketIO™ GTP transceivers• Users can configure Virtex-5 GTP transceivers toconform to industry standard protocols usingpredefined templates, or tailor the templates forcustom protocols• Included protocol templates provide support for thefollowing specifications: Aurora, CPRI, FibreChannel 1x, Gigabit Ethernet, HD-SDI, OBSAI,OC3, OC12, OC48, PCI Express® (PCIe®), SATA,SATA II, and XAUI• Automatically configures analog settings• Each custom wrapper includes example design, testbench; and both implementation and simulation scripts
標簽： Transceiver Virtex Wizar GTP
上傳時間： 2013-10-23
上傳用戶：leyesome
1 Communication Protocol (Computer as master) The communication protocol describes here allows your computer to access 4096 internal registers (W0000-W4095) and 1024 internal relays (B0000-B1023) in the Workstation.. 1.1 Request Message Format Request message is a command message to be sent from the computer to the Workstation. The data structure of request message is shown below. Note that numbers are always in hexadecimal form and converted into ASCII characters. For example, Workstation unit number 14 will appear in the message as character 0(30h) followed by character E(45h); a BCC of 5Ah will appear in the message as character 5(35h) followed by character A(41h).
上傳時間： 2013-10-28
上傳用戶：cxl274287265
The Tri-Mode Ethernet MAC (TEMAC) UltraController-II module is a minimal footprint,embedded network processing engine based on the PowerPC™ 405 (PPC405) processor coreand the TEMAC core embedded within a Virtex™-4 FX Platform FPGA. The TEMACUltraController-II module connects to an external PHY through Gigabit Media IndependentInterface (GMII) and Management Data Input/Output (MDIO) interfaces and supports tri-mode(10/100/1000 Mb/s) Ethernet. Software running from the processor cache reads and writesthrough an On-Chip Memory (OCM) interface to two FIFOs that act as buffers between thedifferent clock domains of the PPC405 OCM and the TEMAC.
上傳時間： 2013-10-26
上傳用戶：yuzsu
In today’s world of modular networking and telecommunications design, it is becomingincreasingly difficult to keep alignment with the many different and often changing interfaces,both inter-board and intra-board. Each manufacturer has their own spin on the way in whichdevices are connected. To satisfy the needs of our customers, we must be able to support alltheir interface requirements. For us to be able to make products for many customers, we mustadopt a modular approach to the design. This modularity is the one issue that drives the majorproblem of shifting our bits from one modular interface to another.
上傳時間： 2013-11-25
上傳用戶：suicone
針對飛行模擬器座艙數據采集的復雜性，設計了一種基于以太網分布式的數據采集控制系統，該系統是RCM5700微處理器模塊上的以太網應用。在系統的基礎上具體討論了PoE技術的應用，在傳輸數據的網線上同時提供電流，提出并實現了一種包括輔助電源在內的完整可靠的PoE供電方案。設計采用美國國家半導體的LM5073和LM5576并根據不同的負載情況，進行穩定可靠的電壓轉換，以滿足數據采集電路的要求。實驗結果表明：該設計穩定可靠，滿足低于13 W的采集節點供電要求，提高了模擬器信號采集系統的通用性和標準化程度，避免了以往數據采集節點單獨繁瑣的電源設計。 Abstract: Aiming at the complexity of large avion simulation and controlling，the simulator cabin distribute data collecting and control system was designed. This system is the application of RCM5700 on Ethernet. Based on this system，PoE technique that makes Ethernet can also provide power were expounded with emphasis and included FAUX design the PoE resolution was realized. To achieve the requirement of this system，LM5073 and LM5576 were used to DC-DC switch. From the data of experiment，the design filled the requirement of power-need of node whose power was lower than 13W. The application of the technique can advance the degree of simulation data collections currency and standardization and avoid designing additional power system.
上傳時間： 2013-11-09
上傳用戶：xyipie
