WHAT MIME64 IS: MIME64 is an encoding described in RFC1341 as MIME base64.Its purpose is to encode binary files into ASCII so that they may be passedthrough e-mail gates. In this regard, MIME64 is similar to UUENCODE.Although most binaries these days are transmitted using UUENCODE, Ihave seen a few using MIME64, and I have had requests from friends thatI decode MIME64 files that have fallen into their hands. As long assome MIME64 continues to exist, a package such as this one is usefulto have.
Information in this document is subject to change without notice. Companies, names, and data used in examples herein are fictitious unless otherwise noted. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Microsoft Corporation.
OLE Programmer s Reference
Information in this online help system is subject to change without notice and does not represent a commitment on the part of Microsoft Corporation. The software and/or files described in this online help system are furnished under a license agreement or nondisclosure agreement. The software and/or files may be used or copied only in accordance with the terms of the agreement. The purchaser may make one copy of the software for backup purposes. No part of this online help system may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording, or information and retrieval systems, for any purpose other than the purchaser s personal use, without the written permission of Microsoft Corporation.
Streaming refers to the ability of an application to play synchronised media streams like audio and video streams in a continuous way while those streams are being transmitted to the client over a data network.
This paper examines the asymptotic (large sample) performance
of a family of non-data aided feedforward (NDA FF) nonlinear
least-squares (NLS) type carrier frequency estimators for burst-mode
phase shift keying (PSK) modulations transmitted through AWGN and
flat Ricean-fading channels. The asymptotic performance of these estimators
is established in closed-form expression and compared with the
modified Cram`er-Rao bound (MCRB). A best linear unbiased estimator
(BLUE), which exhibits the lowest asymptotic variance within the family
of NDA FF NLS-type estimators, is also proposed.
This program demonstrates operation of ADC0 in polled mode. The ADC0 is
// configured to use writes to AD0BUSY as its start of conversion source and
// to measure the output of the on-chip temperature sensor. The temperature
// sensor output is converted to degrees Celsius and is transmitted out UART0
This program demonstrates operation of ADC0 in polled mode. The ADC0 is
// configured to use writes to AD0BUSY as its start of conversion source and
// to measure the output of the on-chip temperature sensor. The temperature
// sensor output is converted to degrees Celsius and is transmitted out UART0
This article describes a sniffer for Windows. WinSniff is an application for capturing packets on the network. It displays all the packets that are transmitted on the local network and gives detailed information about each header in the packet. In order to keep it simple, I am not dealing with application level protocols. If you are interested, you can add features to support various application level protocols such as SMTP, FTP, NETBIOS etc
基于OFDM的無線寬帶系統仿真It contains mainly two parts, i.e. link-level simulator and system-level simulator.
Link-level simulator focus on a single-cell single-user scenario, where signal is transmitted from tx, and estimated at rx. Comparing the difference in tx/rx signal, the error rate can be found out. The output of the link-level simulator is the BLER/BER vs. SNR mapping table, that can be used for the system-level simulation.
System-level simulator focus on a multi-cell multi-user scenario. For the sake of simplicity, it takes the mapping table aquired in the link-level simulation, measure the actural SNR, and finds the corresponding error rate.
This example provides a description of how to use a DMA channel to transfer a
word data buffer from memory (Flash) to memory (RAM).
The dedicated DMA channel is configured to transfer once a time a 32 word data buffer
stored as constant in the Flash memory to another buffer in the RAM memory.
The received data are stored in the DST_Buffer.
The DMA channel transfer complete interrupt is enabled to generate an interrupt at
the end of the buffer transfer. As soon as the transfer is completed an interrupt is
generated and in the DMA channel interrupt routine the transfer complete interrupt
pending bit is cleared.
The data counter is stored before and after the transfer to show that all data has been
transfered.
TransferStatus gives the data transfer status where it is PASSED if transmitted and
received data are the same otherwise it is FAILED
