特點 最高輸入頻率 10KHz 計數速度 50/10000脈波/秒可選擇 四種輸入模式可選擇(加算,減算,加減算,90度相位差加減算) 90度相位差加減算具有提高解析度4倍功能 輸入脈波具有預設刻度功能 計數暫時停止功能 3組報警功能 15BIT類比輸出功能 數位RS-485界面 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脈波觸發電位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高輸入頻率: <10KHz (up,down,up/down mode) <3KHz (quadrature mode) 輸出動作時間 : 0.1 to 99.9 second adjustable 輸出復歸方式: Manual(N) or automatic (R or C) can be modif 繼電器容量: AC 250V-5A, DC 30V-7A 顯示值范圍: -199999 to 999999 類比輸出解析度: 15 bit DAC 輸出反應速度: < 1/f+10ms(0-90%) 輸出負載能力: < 10mA for voltage mode < 10V for current mode <[(V+)-7.5V]/20mA for two-wire mode 輸出之漣波: < 0.1% F.S. 通訊位址: "01"-"FF" 傳輸速度: 19200/9600/4800/2400 selective 通信協議: Modbus RTU mode 顯示幕: Red high efficiency LEDs high 14.22mm (.56") 參數設定方式: Touch switches 感應器電源: 12VDC +/-3%(<60mA) 記憶方式: Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
We offer a broad line of high performance low dropout (LDO) linear regulators with fasttransient response, excellent line and load regulation, and very wide input voltage rangefrom 0.9V to 100V. Output currents range from 20mA to 10A, with positive, negative andmultiple output versions available. Many devices offer output voltage operation <0.8V andsome feature operation as low as 0V, even with a single supply. Most are stable with ceramicoutput capacitors. LDO regulators can be applied in virtually any application.
Applying power to a standard logic chip, SRAM, or EPROM, usually results in output pinstracking the applied voltage as it rises. Programmable logic attempts to emulate that behavior,but physics forbids perfect emulation, due to the device programmability. It requires care tospecify the pin behavior, because programmable parts encounter unknown variables – yourdesign and your power environment.
為了提高直接轉矩控制（DTC）系統定子磁鏈估計精度，降低電流、電壓測量的隨機誤差，提出了一種基于擴展卡爾曼濾波（EKF）實現異步電機轉子位置和速度估計的方法。擴展卡爾曼濾波器是建立在基于旋轉坐標系下由定子電流、電壓、轉子轉速和其它電機參量所構成的電機模型上，將定子電流、定子磁鏈、轉速和轉子角位置作為狀態變量，定子電壓為輸入變量，定子電流為輸出變量，通過對磁鏈和轉速的閉環控制提高定子磁鏈的估計精度，實現了異步電機的無速度傳感器直接轉矩控制策略，仿真結果驗證了該方法的可行性,提高了直接轉矩的控制性能。
Abstract:
In order to improve the Direct Torque Control（DTC） system of stator flux estimation accuracy and reduce the current， voltage measurement of random error， a novel method to estimate the speed and rotor position of asynchronous motor based on extended Kalman filter was introduced. EKF was based on d-p axis motor and other motor parameters （state vector: stator current， stator flux linkage， rotor angular speed and position； input: stator voltage； output: staror current). EKF was designed for stator flux and rotor speed estimation in close-loop control. It can improve the estimated accuracy of stator flux. It is possible to estimate the speed and rotor position and implement asynchronous motor drives without position and speed sensors. The simulation results show it is efficient and improves the control performance.
Semiconductor memory, card readers, microprocessors,disc drives, piezoelectric devices and digitally based systemsfurnish transient loads that a voltage regulator mustservice. Ideally, regulator output is invariant during a loadtransient. In practice, some variation is encountered andbecomes problematic if allowable operating voltage tolerancesare exceeded. This mandates testing the regulatorand its associated support components to verify desiredperformance under transient loading conditions. Variousmethods are employable to generate transient loads, allowingobservation of regulator response
在Multisim 10軟件環境下，設計一種由運算放大器構成的精確可控矩形波信號發生器，結合系統電路原理圖重點闡述了各參數指標的實現與測試方法。通過改變RC電路的電容充、放電路徑和時間常數實現了占空比和頻率的調節，通過多路開關投入不同數值的電容實現了頻段的調節，通過電壓取樣和同相放大電路實現了輸出電壓幅值的調節并提高了電路的帶負載能力，可作為頻率和幅值可調的方波信號發生器。Multisim 10仿真分析及應用電路測試結果表明，電路性能指標達到了設計要求。
Abstract:
Based on Multisim 10， this paper designed a kind of rectangular-wave signal generator which could be controlled exactly composed of operational amplifier， the key point was how to implement and test the parameter indicators based on the circuit diagram. The duty and the frequency were adjusted by changing the time constant and the way of charging and discharging of the capacitor， the width of frequency was adjusted by using different capacitors provided with multiple switch， the amplitude of output voltage was adjusted by sampling voltage and using in-phase amplifier circuit，the ability of driving loads was raised， the circuit can be used as squarewave signal generator whose frequency and amplitude can be adjusted. The final simulation results of Multisim 10 and the tests of applicable circuit show that the performance indicators of the circuit meets the design requirements.
