This is an example program showing how to use the LMX2326 chip. The program configures the chip and then prompts the user for a channel number. When the channel number is entered, the pll tunes to the desired frequency.
標簽： program chip configures the
上傳時間： 2017-08-04
上傳用戶：小儒尼尼奧
this is a document about radio frequency identification RFID, this was a project ,i have done last year ,actually this technology is a very inpotrtant one due to its relation with newest technologies , like GPS , or the miniturization of integrated circuits ,and that is described in chapter 3 . chapter 1 gives an introduction of the technology RFID , chapter 2 gives a discussion of a library using RFID , and chapter 3 is about the future of RFID , and finally the conclusion .
標簽： this identification frequency document
上傳時間： 2014-01-10
上傳用戶：gtzj
Feeding antennas with proper signals can be difficult. The signal is often described as a voltage, and voltages are not well defined in electromagnetic wave formulations. There are several tricks to model voltage generators in such situations, and one is the magnetic frill. This model shows the basic steps of defining a magnetic frill voltage generator for a dipole antenna, and it also compares the resulting antenna impedance with known results.
標簽： difficult described antennas Feeding
上傳時間： 2013-12-25
上傳用戶：yulg
Feeding antennas with proper signals can be difficult. The signal is often described as a voltage, and voltages are not well defined in electromagnetic wave formulations. There are several tricks to model voltage generators in such situations, and one is the magnetic frill. This model shows the basic steps of defining a magnetic frill voltage generator for a dipole antenna, and it also compares the resulting antenna impedance with known results.
標簽： difficult described antennas Feeding
上傳時間： 2013-12-21
上傳用戶：GavinNeko
The UMTS Physical Layer model consists of an end-to-end (transmitter-to-receiver) simulation of the Frequency Division Duplex (FDD) Downlink physical layer for several Dedicated Channels (DCH) as specified by the 3GPP standard (Release 99).
標簽： transmitter-to-receiver end-to-end simulation Physical
上傳時間： 2014-01-11
上傳用戶：it男一枚
This is an analog signal communication simulator, usign frequency modulation. It is designed in MATLAB-Simulink. The communications channel beetween the transmitter and the reciever is supposed to be affected by additive white Gaussian noise.
標簽： communication modulation frequency simulator
上傳時間： 2013-12-25
上傳用戶：王楚楚
The AP2406 is a 1.5Mhz constant frequency, slope compensated current mode PWM step-down converter. The device integrates a main switch and a synchronous rectifier for high efficiency without an external Schottky diode. It is ideal for powering portable equipment that runs from a single cell lithium-Ion (Li+) battery. The AP2406 can supply 600mA of load current from a 2.5V to 5.5V input voltage. The output voltage can be regulated as low as 0.6V. The AP2406 can also run at 100% duty cycle for low dropout operation, extending battery life in portable system. Idle mode operation at light loads provides very low output ripple voltage for noise sensitive applications. The AP2406 is offered in a low profile (1mm) 5-pin, thin SOT package, and is available in an adjustable version and fixed output voltage of 1.2V, 1.5V and 1.8V
上傳時間： 2017-02-23
上傳用戶：w124141
This book is intended to help electric power and telephone company personnel and individuals interested in properly protecting critical tele- communications circuits and equipment located in high voltage (HV) environments and to improve service reliability while maintaining safe working conditions. Critical telecommunications circuits are often located in HV environments such as electric utility power plants, substations, cell sites on power towers, and standalone telecommuni- cations facilities such as 911 call centers and mountaintop telecom- munications sites.
標簽： Protection Voltage High
上傳時間： 2020-05-27
上傳用戶：shancjb
OSCILLATORS are key building blocks in integrated transceivers. In wired and wireless communication terminals, the receiver front-end selects, amplifies and converts the desired high-frequency signal to baseband. At baseband the signal can then be converted into the digital domain for further data processing and demodula- tion. The transmitter front-end converts an analog baseband signal to a suitable high- frequency signal that can be transmitted over the wired or wireless channel.
標簽： High-Frequency Oscillator Design
上傳時間： 2020-05-27
上傳用戶：shancjb
With the rapid expansion of wireless consumer products,there has been a con- siderable increase in the need for radio-frequency (RF) planning, link plan- ning, and propagation modeling.A network designer with no RF background may find himself/herself designing a wireless network. A wide array of RF planning software packages can provide some support, but there is no substi- tute for a fundamental understanding of the propagation process and the lim- itations of the models employed. Blind use of computer-aided design (CAD) programs with no understanding of the physical fundamentals underlying the process can be a recipe for disaster. Having witnessed the results of this approach, I hope to spare others this frustration.
標簽： Introduction Propagation to RF
上傳時間： 2020-05-27
上傳用戶：shancjb
