為了使音頻信號分析儀小巧可靠，成本低廉，設計了以2片MSP430F1611單片機為核心的系統。該系統將音頻信號送入八階巴特沃茲低通濾波器，對信號進行限幅放大、衰減、電平位移、緩沖，并利用一單片機負責對前級處理后的模擬信號進行采樣，將采集得到的音頻信號進行4 096點基2的FFT計算，并對信號加窗函數提高分辨率，另一單片機負責對信號的分析及控制顯示設備。此設計精確的測量了音頻信號的功率譜、周期性、失真度指標，達到較高的頻率分辨率，并能將測量結果通過紅外遙控器顯示在液晶屏上。 Abstract: o make the audio signal analyzer cheaper， smaller and more reliable， this system sends the audio signal to the eight-order butterworth filter， and then amplifies， attenuates， buffers it in a limiting range， transfers the voltage level of the signal before utilizing two MSP430F1611 MCU to realize the audio analysis. One is charged for sampling and dealing with the processed audio signal collected by the 4096 point radix-2 FFT calculation and imposes the window function to improve the frequency resolution. The other one controls the display and realizes the spectrum， periodicity， power distortion analysis in high resolution which is displayed in the LCD screen through the infrared remote control.
上傳時間： 2013-12-11
上傳用戶：jasonheung
通過比較各種隔離數字通信的特點和應用范圍，指出塑料光纖在隔離數字通信中的優勢。使用已經標準化的TOSLINK接口，有利于節省硬件開發成本和簡化設計難度。給出了塑料光纖的硬件驅動電路，說明設計過程中的注意事項，對光收發模塊的電壓特性和頻率特性進行全面試驗，并給出SPI口使用塑料光纖隔離通信的典型應用電路圖。試驗結果表明，該設計可為電力現場、電力電子及儀器儀表的設計提供參考。 Abstract: y comparing characteristics and applications area of various isolated digital communications， this article indicates advantages of plastic optical fiber in isolated digital communications. Using the standardized TOSLINK interface， it helps to control costs and difficulty in hardware development and design. Then it gives the hardware driver circuit of plastic optical fiber module， explains the noticed details in design process， gives results on the basis of the optical transceiver module voltage characteristics and frequency characteristics tests. Finally，it gives typical application circuit of the SPI communication port by using plastic optical fiber isolation .The results show that this design can be referenced for the power field， power electronics and instrumentation design.
上傳時間： 2014-01-10
上傳用戶：gundan
微電腦型單相交流集合式電表（單相二線系統） 特點： 精確度0.25%滿刻度±1位數 可同時量測與顯示交流電壓,電流,頻率,瓦特,(功率因數/視在功率) 交流電壓,電流,瓦特皆為真正有效值(TRMS) 交流電流,瓦特之小數點可任意設定 瓦特單位W或KW可任意設定 CT比可任意設定(1至999) 輸入與輸出絕緣耐壓 2仟伏特/1分鐘( 突波測試強度4仟伏特(1.2x50us) 數位RS-485界面 (Optional) 主要規格： 精確度: 0.1% F.S.±1 digit (Frequency) 0.25% F.S.±1 digit(ACA,ACV,Watt,VA) 0.25% F.S. ±0.25o(Power Factor) (-.300~+.300) 輸入負載: <0.2VA (Voltage) <0.2VA (Current) 最大過載能力: Current related input: 3 x rated continuous 10 x rated 30 sec. 25 x rated 3sec. 50 x rated 1sec. Voltage related input: maximum 2 x rated continuous 過載顯示: "doFL" 顯示值范圍: 0~600.0V(Voltage) 0~999.9Hz(Frequency)(<20% for voltage input) 0~19999 digit adjustable(Current,Watt,VA) 取樣時間: 2 cycles/sec. RS-485通訊位址: "01"-"FF" RS-485傳輸速度: 19200/9600/4800/2400 selective RS-485通信協議: Modbus RTU mode 溫度系數: 100ppm/℃ (0-50℃) 顯示幕: Red high efficiency LEDs high 10.16 mm(0.4") 參數設定方式: Touch switches 記憶型式: Non-volatile E²PROM memory 絕緣抗阻: >100Mohm with 500V DC 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600 Vdc (input/output) 突波測試: ANSI c37.90a/1974,DIN-IEC 255-4 impulse voltage 4KV(1.2x50us) 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上傳時間： 2015-01-03
上傳用戶：幾何公差
在Multisim 10軟件環境下，設計一種由運算放大器構成的精確可控矩形波信號發生器，結合系統電路原理圖重點闡述了各參數指標的實現與測試方法。通過改變RC電路的電容充、放電路徑和時間常數實現了占空比和頻率的調節，通過多路開關投入不同數值的電容實現了頻段的調節，通過電壓取樣和同相放大電路實現了輸出電壓幅值的調節并提高了電路的帶負載能力，可作為頻率和幅值可調的方波信號發生器。Multisim 10仿真分析及應用電路測試結果表明，電路性能指標達到了設計要求。 Abstract: Based on Multisim 10， this paper designed a kind of rectangular-wave signal generator which could be controlled exactly composed of operational amplifier， the key point was how to implement and test the parameter indicators based on the circuit diagram. The duty and the frequency were adjusted by changing the time constant and the way of charging and discharging of the capacitor， the width of frequency was adjusted by using different capacitors provided with multiple switch， the amplitude of output voltage was adjusted by sampling voltage and using in-phase amplifier circuit，the ability of driving loads was raised， the circuit can be used as squarewave signal generator whose frequency and amplitude can be adjusted. The final simulation results of Multisim 10 and the tests of applicable circuit show that the performance indicators of the circuit meets the design requirements.
上傳時間： 2014-01-21
上傳用戶：shen007yue
A simple C program to strobe the LEDsvia Port D. The strobe rate is to be set by adjusting the voltage drop over a potentiometer that is sampled by an ADC.
上傳時間： 2014-01-09
上傳用戶：lifangyuan12
Routine mampres: To obtain amplitude response from h(exp(jw)). input parameters: h :n dimensioned complex array. the frequency response is stored in h(0) to h(n-1). n :the dimension of h and amp. fs :sampling frequency (Hz). iamp:If iamp=0: The Amplitude Res. amp(k)=abs(h(k)) If iamp=1: The Amplitude Res. amp(k)=20.*alog10(abs(h(k))). output parameters: amp :n dimensioned real array. the amplitude-frequency response is stored in amp(0) to amp(n-1). Note: this program will generate a data file "filename.dat" . in chapter 2
標簽： dimensione parameters amplitude response
上傳時間： 2013-12-19
上傳用戶：xfbs821
Rotating shafts experience a an elliptical motion called whirl. It is important to decompose this motion into a forward and backward whil orbits. The current function makes use of two sensors to generate a bi-directional spectrogram. The method can be extended to any time-frequency distribution ％ ％ compute the forward/backward Campbell/specgtrogram ％ ％ INPUT: ％ y (n x 2) each column is measured from a different sensor ％ /////// ％ __ ％ |s1| y(:,1) ％ |__| ％ __ ％ / \ ________|/ ％ | | | s2 |/ y(:,2) ％ \____/ --------|/ ％ ％ Fs Sampling frequnecy ％ ％ OUTPUT: ％ B spectrogram/Campbel diagram ％ x x-axis coordinate vector (time or Speed) ％ y y-axis coordinate vector (frequency [Hz])
標簽： experience elliptical decompose important
上傳時間： 2015-06-23
上傳用戶：372825274
in this paper,wo propose an extension of the zerotree-based space-frequency quantization algorithm by adding a wedgelet symbol to its tree-pruning optimization.
標簽： space-frequency zerotree-based quantization algorithm
上傳時間： 2015-10-22
上傳用戶：yxgi5
t transistor has the characteristics of components of the sensor real-time measurement of voltage and current signals through, obtained quality factor correction circuit for the feedback and the feedback time, IBM used the feedback field effect transistor implementation, in order to achieve quality factor correction circ
標簽： characteristics measurement transistor components
上傳時間： 2014-12-22
上傳用戶：杜瑩12345
This directory contains example ADSPBF535 code, written in assembly, that changes the frequency and voltage using the push button switches on the board.
標簽： directory frequency contains assembly
上傳時間： 2014-01-03
上傳用戶：evil
