Abstract: This Design idea explains how to implement an 8-bit analog-to-digital converter (ADC), using a microcontroller
上傳時間： 2013-10-30
上傳用戶：愛死愛死
Abstract: A perfect voltage reference produces a stable voltage independent of any external factors. Real-world voltagereferences, of course, are subject to errors caused by many external factors. One causeof these major errors istemperature. Without care, it is easy to operate a voltage reference outside its operating temperature range. Thisapplication note describes how references respond to temperature changes, and how self-heating can cause a voltagereference to operate outside its recommended temperature range. Once understood, this knowledge can then be used toavoid making this Design error.
上傳時間： 2013-11-08
上傳用戶：xianglee
平行耦合微帶線帶通濾波器在微波電路系統中廣泛應用。為了提高帶通濾波器性能，縮短設計周期，采用奇偶模原理分析與ADS（Advanced Design System）仿真相結合的方法，設計出一個中心頻率為2.5 GHz，相對帶寬為10%的平行耦合微帶線帶通濾波器。進一步優化參數，得到電路版圖。最終結果證明，這種方法具有設計周期短、可靠性高的特點，且各項參數滿足設計要求。
上傳時間： 2013-10-12
上傳用戶：jrsoft
Abstract: A laser module Designer can use a fixed resistor, mechanical pot, digital pot, or a digital-to-analogconverter (DAC) to control the laser driver's modulation and bias currents. The advantages of a programmablemethod (POT or DAC) are that the manufacturing process can be automated and digital control can be applied(e.g., to compensate for temperature). Using POTs can be a more simple approach than a DAC. There can be aslight cost advantage to using a POT, but this is usually not significant relative to other pieces of the Design.Using a DAC can offer advantages, including improved linearity (translating to ease of software implementationand ability to hit the required accuracy), increased board density, a wider range of resolutions, a betteroptimization range, ease of use with a negative voltage laser driver, and unit-to-unit consistency
上傳時間： 2013-11-13
上傳用戶：ca05991270
This document and the associated reference Design provide guidance for assigning anddebugging software to or in FLASH memory, specifically for a MicroBlaze™ embeddedprocessor Design.
上傳時間： 2013-11-11
上傳用戶：dgann
Photodiodes can be broken into two categories: largearea photodiodes with their attendant high capacitance(30pF to 3000pF) and smaller area photodiodes withrelatively low capacitance (10pF or less). For optimalsignal-to-noise performance, a transimpedance amplifi erconsisting of an inverting op amp and a feedback resistoris most commonly used to convert the photodiode currentinto voltage. In low noise amplifi er Design, large areaphotodiode amplifi ers require more attention to reducingop amp input voltage noise, while small area photodiodeamplifi ers require more attention to reducing op amp inputcurrent noise and parasitic capacitances.
上傳時間： 2013-10-28
上傳用戶：hanbeidang
Digital-to-analog converters (DACs) are prevalent inindustrial control and automated test applications.General-purpose automated test equipment often requiresmany channels of precisely controlled voltagesthat span several voltage ranges. The LTC2704 is ahighly integrated 16-bit, 4-channel DAC for high-endapplications. It has a wide range of features Designed toincrease performance and simplify Design.
上傳時間： 2013-11-22
上傳用戶：元宵漢堡包
Recent advances in low voltage silicon germaniumand BiCMOS processes have allowed the Design andproduction of very high speed amplifi ers. Because theprocesses are low voltage, most of the amplifi er Designshave incorporated differential inputs and outputs to regainand maximize total output signal swing. Since many lowvoltageapplications are single-ended, the questions arise,“How can I use a differential I/O amplifi er in a single-endedapplication?” and “What are the implications of suchuse?” This Design Note addresses some of the practicalimplications and demonstrates specifi c single-endedapplications using the 3GHz gain-bandwidth LTC6406differential I/O amplifi er.
上傳時間： 2013-11-23
上傳用戶：rocketrevenge
The Reactor Design pattern handles service requests that are delivered concurrently to an application by one or more clients. Each service in an application may consist of serveral methods and is represented by a separate event handler that is responsible for dispatching service-specific requests.
上傳時間： 2013-10-15
上傳用戶：libinxny
This note describes some of the unique IC Design techniques incorporated into a fast, monolithic power buffer, the LT1010. Also, some application ideas are described such as capacitive load driving, boosting fast op amp output current and power supply circuits.
上傳時間： 2013-11-12
上傳用戶：671145514
