iso u-p-o 系列直流電壓信號隔離放大器是一種將電壓信號轉換成按比例輸出的隔離電流或電壓信號的混合集成電路。該ic內部含有一組高隔離的dc/dc電源和電壓信號高效率耦合隔離變換電路等，可以將直流電壓小信號進行隔離放大（u/u）輸出或直接轉換為直流電流（u /i）信號輸出。較大的輸入阻抗（≥1 mω）,較強的帶負載能力（電流輸出＞650ω,電壓輸出≥2kω）能實現小信號遠程無失真的傳輸。 ic內部可采用陶瓷基板、印刷電阻全smt的可靠工藝制作及使用新技術隔離措施，使器件能滿足信號輸入/輸出/輔助電源之間3kv三隔離和工業級寬溫度、潮濕震動等現場環境要求。外接滿度校正和零點校正的多圈電位器可實現 0-5V/0-10v/1-5V4-20ma/0-20ma等信號之間的隔離和轉換。（精度線性高，隔離電壓3000vdc）
上傳時間： 2014-12-23
上傳用戶：392210346
特征： 分辨率： 24 位（無失碼） 有效位數： 21位（ PGA = 128 特征： 分辨率：24位（無失碼） 有效位數：21位 輸出碼率：10Hz/80Hz（可選） 通道固定增益：128倍 對50Hz、60Hz噪聲抑制：-100dB 工作電壓：2.5V – 6v 可選擇的內外置晶振 簡單的SPI接口 應用場合： 電子秤、數字壓力傳感器； 血壓計等醫療儀器； 微弱信號測量及工業控制 其他相關資料需求：18938649401@189.cn 18938649401
上傳時間： 2013-11-19
上傳用戶：英雄
The purpose of this application note is to show an example of how a digital potentiometer can be used in thefeedback loop of a step-up DC-DC converter to provide calibration and/or adjustment of the output voltage.The example circuit uses a MAX5025 step-up DC-DC converter (capable of generating up to 36V,120mWmax) in conjunction with a DS1845, 256 position, NV digital potentiometer. For this example, the desiredoutput voltage is 32V, which is generated from an input supply of 5V. The output voltage can be adjusted in35mV increments (near 32V) and span a range wide enough to account for resistance, potentiometer and DCDCconverter tolerances (27.6V to 36.7V).
上傳時間： 2014-12-23
上傳用戶：781354052
經整流橋整流出的直流電壓 110V，由D906 整流，經R911，R912 后，再由C911 濾波，到UC3842 的⑦腳，當⑦腳，當⑦腳電壓在16V-34V 之間時，UC3842 開始工作，此時⑧腳有了5V 的基準電壓，⑥腳輸出脈沖，使開關管Q901 導通，此時，變壓器初級線圈（4-6）有電流產生，產生感應電動勢，根據互感原理，初級線圈（1-2）也產生感應電壓，經R913，D910 整流C911 濾波后為UC3842 的⑦腳供電...
上傳時間： 2013-11-04
上傳用戶：wuyuying
The LTC®1966 is a true RMS-to-DC converter that uses aDS computational technique to make it dramatically simplerto use, significantly more accurate, lower in powerconsumption and more flexible than conventional logantilogRMS-to-DC converters. The LTC1966 RMS-to-DCconverter has an input signal range from 5mVRMS to1.5VRMS (a 50dB dynamic range with a single 5V supplyrail) and a 3dB bandwidth of 800kHz with signal crestfactors up to four.
上傳時間： 2013-10-12
上傳用戶：qilin
555 定時器是一種模擬和數字功能相結合的中規模集成器件。一般用雙極性工藝制作的稱為555，用CMOS 工藝制作的稱為7555，除單定時器外，還有對應的雙定時器556/7556。555 定時器的電源電壓范圍寬，可在4.5V~16V 工作，7555 可在3~18V 工作，輸出驅動電流約為200mA，因而其輸出可與TTL、CMOS 或者模擬電路電平兼容。
上傳時間： 2013-10-18
上傳用戶：農藥鋒6
Portable, battery-powered operation of electronic apparatushas become increasingly desirable. Medical, remotedata acquisition, power monitoring and other applicationsare good candidates for battery operation. In some circumstances,due to space, power or reliability considerations,it is preferable to operate the circuitry from a single 1.5Vcell. Unfortunately, a 1.5V supply eliminates almost alllinear ICs as design candidates. In fact, the LM10 opamp-reference and the LT®1017/LT1018 comparators arethe only IC gain blocks fully specifi ed for 1.5V operation.Further complications are presented by the 600mV dropof silicon transistors and diodes. This limitation consumesa substantial portion of available supply range, makingcircuit design diffi cult. Additionally, any circuit designedfor 1.5V operation must function at end-of-life batteryvoltage, typically 1.3V. (See Box Section, “Componentsfor 1.5V Operation.”)
標簽： Circuitry Operation Single 1017
上傳時間： 2013-12-20
上傳用戶：Wwill
This reference design (RD) features a fullyassembled and tested surface-mount printed circuitboard (PCB). The RD board utilizes the MAX48851:2 or 2:1 multiplexer and other ICs to implement acomplete video graphics array (VGA) 8:1multiplexer.VGA input/output connections are provided to easilyinterface the MAX4885 RD board with VGAcompatibledevices. The RD board gives the optionto use a single 5V DC power supply (V+), or this RDboard can be powered from any one of the eight VGA sources.
標簽： multiplexer reference VGA
上傳時間： 2013-11-09
上傳用戶：ANRAN
OPTOELECTRONICS CIRCUIT COLLECTION AVALANCHE PHOTODIODE BIAS SUPPLY 1Provides an output voltage of 0V to +80V for reverse biasingan avalanche photodiode to control its gain. This circuit canalso be reconfigured to supply a 0V to –80V output.LINEAR TEC DRIVER–1This is a bridge-tied load (BTL) linear amplifier for drivinga thermoelectric cooler (TEC). It operates on a single +5Vsupply and can drive ±2A into a common TEC.LINEAR TEC DRIVER–2This is very similar to DRIVER–1 but its power output stagewas modified to operate from a single +3.3V supply in orderto increase its efficiency. Driving this amplifier from astandard +2.5V referenced signal causes the output transistorsto have unequal power dissipation.LINEAR TEC DRIVER–3This BTL TEC driver power output stage achieves very highefficiency by swinging very close to its supply rails, ±2.5V.This driver can also drive ±2A into a common TEC. Operationis shown with the power output stage operating on±1.5V supplies. Under these conditions, this linear amplifiercan achieve very high efficiency. Application ReportThe following collection of analog circuits may be useful in electro-optics applications such as optical networkingsystems. This page summarizes their salient characteristics.
上傳時間： 2013-10-27
上傳用戶：落花無痕
電壓源電流源名字上僅差一個字…HE HE.有一些朋友對此不太明白.所以特此說明下…并以軟件仿真…詳細介紹工作原理…以及注意事項….下面就是電壓源和電流的符號…左邊是電流源,右邊是電壓源. 電壓源…電壓源其實就是我們普通經常用的一種電源.比如說電池呀電瓶或自己做的穩壓電路.一般屬于電壓源… 電壓源的特性是: 輸出端,可以開路,但不能短路…總而言之電壓源的輸出電壓是恒定的…比如5V 電壓源輸出的電壓就是5V.隨不同的負載會改變電流…比如在5V 的電壓源上加一個1 歐的負載… 流過的電流就是5/1=5A 電流… 如果接的電阻為2 歐.流過電流就等于5/2=2.5A….這個簡單的計算相信誰都會…電流源電流源和電壓源區別比較大…電流源輸出端不能開路,但可以短路…為什么不能開路呢…HE HE…是因為開路了…電流源輸出的電壓就為無限高了…(實際上電壓也是有一定值的)總而言之電流源的輸出電流是恒定的.不管你負載的大小…就是你短路了.他的電流還是保持不變.改變的是電壓…比如一個1A的恒流源…你接上一個1歐的負載…他輸出的電壓是.1x1=1V 電壓…當你接上一個10 歐電阻的時候…他就是1x10=10V電壓輸出…
上傳時間： 2013-10-08
上傳用戶：kaixinxin196
