友善之臂的QtEmbedded實例教程 第一章 LINUX 圖形用戶界面 GUI 介紹.....................................................................................1 1.1 常用 GUI 介紹...................................................................................................................1 1.2 關于 Qt...............................................................................................................................2 1.3 Qt/Embedded 簡介.............................................................................................................4 1.4 Qtopia 介紹.........................................................................................................................4 第二章 QT的安裝..........................................................................................................................6 2.1 Qt X11 的安裝....................................................................................................................6 2.2 Qt/Embedded 安裝..............................................................................................................9 2.3 Qtopia 編譯.......................................................................................................................11 第三章 QT的編程........................................................................................................................12 實驗一 “Hello word！ ”Qt初探............................................................................................12 實驗二 創建一個窗口并添加按鈕.......................................................................................17 實驗三 對象間通信：Signal 和 Slot 機制........................................................................20 實驗四 菜單和快捷鍵...........................................................................................................29 實驗五 工具條和狀態欄.......................................................................................................38 實驗六 鼠標和鍵盤事件.......................................................................................................48 實驗七 對話框.......................................................................................................................63 實驗八 Qt 中的繪圖..............................................................................................................75 實驗九 Qt 中的多線程編程..................................................................................................85 實驗十 Qt 中的網絡編程......................................................................................................97 第四章 QT常用工具的介紹...................................................................................................... 111 4.1 Qt 設計器（Qt Designer）............................................................................................ 111 4.2 Tmake..............................................................................................................................113 4.3 Qvfb ................................................................................................................................114
標簽： QtEmbedded 教程
上傳時間： 2013-12-21
上傳用戶：laozhanshi111
altium dedigned 安裝地址！
標簽： Altium_Designer 10.0 破解版
上傳時間： 2013-11-06
上傳用戶：ztj182002
With the Altera Nios II embedded processor, you as the system designercan accelerate time-critical software algorithms by adding custominstructions to the Nios II processor instruction set. Using custominstructions, you can reduce a complex sequence of standard instructionsto a single instruction implemented in hardware. You can use this featurefor a variety of applications, for example, to optimize software innerloops for digital signal processing (DSP), packet header processing, andcomputation-intensive applications. The Nios II configuration wizard,part of the Quartus® II software’s SOPC Builder, provides a graphicaluser interface (GUI) used to add up to 256 custom instructions to theNios II processor
上傳時間： 2013-11-07
上傳用戶：swing
電力設備熱點溫度與電流在線監測預警系統工作在大型變壓器旁，極易受電磁輻射干擾，針對該預警系統的子系統：無線傳輸部分進行了抗電磁干擾設計，采用Ansoft Designer軟件仿真分析了PCB（Printed Circuit Board）中電磁波對PCB電磁兼容性產生的影響，根據其得出的PCB的電流圖及近場分布圖，分析PCB的電磁兼容性，針對結果中的電磁輻射過高區域進行了重新設計，經Ansoft Designer驗證，重新設計后的PCB各項指數有所下降，電磁兼容性得到提高。
上傳時間： 2013-11-11
上傳用戶：ggwz258
AltiumDesigner安裝包
標簽： DesignerSummer Altium 18802 Build
上傳時間： 2014-12-31
上傳用戶：zhaistone
AltiumDesigner安裝包
標簽： DesignerSummer Altium 18802 Build
上傳時間： 2013-10-26
上傳用戶：wyc199288
制作此教程的目的旨在學習， 網上也有很多講的比較好的教程，此做并不是想跟他們比什么，希望此教程能對大家學習有所幫助。每個教程講的內容不盡相同，希望此教程能夠幫助大家快速學習Alitum Designer、PADS 和Cadence。
上傳時間： 2013-11-04
上傳用戶：fudong911
Proteus和Altium的聯合使用
上傳時間： 2013-12-22
上傳用戶：Zero_Zero
Nios II定制指令用戶指南：With the Altera Nios II embedded processor, you as the system designer can accelerate time-critical software algorithms by adding custom instructions to the Nios II processor instruction set. Using custom instructions, you can reduce a complex sequence of standard instructions to a single instruction implemented in hardware. You can use this feature for a variety of applications, for example, to optimize software inner loops for digital signal processing (DSP), packet header processing, and computation-intensive applications. The Nios II configuration wizard,part of the Quartus® II software’s SOPC Builder, provides a graphical user interface (GUI) used to add up to 256 custom instructions to the Nios II processor. The custom instruction logic connects directly to the Nios II arithmetic logic unit (ALU) as shown in Figure 1–1.
上傳時間： 2013-10-12
上傳用戶：kang1923
初學altium 教程
標簽： Altium_Designer 使用教程
上傳時間： 2013-11-13
上傳用戶：誰偷了我的麥兜
