在研究傳統家用燃氣報警器的基礎上，以ZigBee協議為平臺，構建mesh網狀網絡實現網絡化的智能語音報警系統。由于傳感器本身的溫度和實際環境溫度的影響，傳感器標定后采用軟件補償方法。為了減少系統費用，前端節點采用半功能節點設備，路由器和協調器采用全功能節點設備，構建mesh網絡所形成的家庭內部報警系統，通過通用的電話接口連接到外部的公用電話網絡，啟動語音模塊進行報警。實驗結果表明，在2.4 GHz頻率下傳輸，有墻等障礙物的情況下，節點的傳輸距離大約為35 m，能夠滿足家庭需要，且系統工作穩定，但在功耗方面仍需進一步改善。
Abstract:
On the basis of studying traditional household gas alarm system, this paper proposed the platform for the ZigBee protocol，and constructed mesh network to achieve network-based intelligent voice alarm system. Because of the sensor temperature and the actual environment temperature, this system design used software compensation after calibrating sensor. In order to reduce system cost, semi-functional node devices were used as front-end node, however, full-function devices were used as routers and coordinator，constructed alarm system within the family by building mesh network，connected to the external public telephone network through the common telephone interface, started the voice alarm module. The results indicate that nodes transmit about 35m in the distance in CASE of walls and other obstacles by 2.4GHz frequency transmission, this is able to meet family needs and work steadily, but still needs further improvement in power consumption.
Calculation of the Differential Impedance of Tracks on FR4 substrates
There is a discrepancy between calculated and measured values of impedance for differential transmission lineson FR4. This is especially noticeable in the CASE of surface microstrip configurations. The anomaly is shown tobe due to the nature of the substrate material. This needs to be considered as a layered structure of epoxy resinand glass fibre. Calculations, using Boundary Element field methods, show that the distribution of the electricfield within this layered structure determines the apparent dielectric constant and therefore affects theimpedance. Thus FR4 cannot be considered to be uniform dielectric when calculating differential impedance.
ACPR (adjacent channel power ratio), AltCPR (alternatechannel power ratio), and noise are important performancemetrics for digital communication systems thatuse, for example, WCDMA (wideband code division multipleaccess) modulation. ACPR and AltCPR are bothmeasures of spectral regrowth. The power in the WCDMAcarrier is measured using a 5MHz measurement bandwidth;see Figure 1. In the CASE of ACPR, the total powerin a 3.84MHz bandwidth centered at 5MHz (the carrierspacing) away from the center of the outermost carrier ismeasured and compared to the carrier power. The resultis expressed in dBc. For AltCPR, the procedure is thesame, except we center the measurement 10MHz awayfrom the center of the outermost carrier.
There are many manufacturers of dot matrix LCD modules. However, most of these displaysare similar. They all have on-board controllers and drivers capable of displaying alpha numericsand a wide variety of other symbols (including Japanese "Katakana" characters). The internaloperation of LCD controller devices is determined by signals sent from a central processing unit(in this CASE, a CoolRunner-II CPLD).
a Java program that reads a file containing instructions written in self-defined file (TPL in this CASE), and executes those instructions. This program should take the name of the TPL file as a command line parameter, and write its output to the console.
access the database using Flash MX. Please remember that Flash is unable to natively access a database. A programming language (ASP in this CASE) provides the programming logic, while Flash works at the presentation tier of the application.
