yright 2002 Cygnal Integrated Products, Inc. // // Filename: LIION_BC_MAIN.c // Target Device: 8051F300 // Created: 11 SEP 2002 // Created By: DKC // Tool chain: KEIL Eval C51 // // This is a stand alone battery charger for a Lithium ION battery. // It utilizes a buck converter, controlled by the on-CHip 8-bit PWM, // to provide constant current followed by constant voltage battery charge.
標簽： LIION_BC_MAIN Integrated Filename Products
上傳時間： 2013-12-23
上傳用戶：牧羊人8920
介紹幾種cpuThe 8xC251SA/SB/SP/SQ improves on the MCS-51 architecture and peripheral features, introducing the advanced register based CPU architecture i.e., the MCS 251 microcontroller architecture. The register based CPU supports a 40-byte register file. In addition, the 8xC251SA/SB/SP/SQ microcontroller has 256-Kbyte expanded external code/data memory space and 64-Kbyte stack space. The new controller is also specially designed to execute C code efficiently. More importantly, the 8xC251SA/SB/SP/SQ maintains binary code compatibility with MCS 51 microcontrollers but at the same time allows the use of the powerful MCS 251 microcontroller instruction set, with many new 8, 16 and 32 bit instructions available. The 8xC251SA/SB/SP/SQ has 512 bytes or 1 Kbyte of on-CHip data RAM options and is available in 16 Kbytes and 8 Kbytes of on-CHip ROM/OTPROM or ROMless options.
標簽： architecture introducin peripheral improves
上傳時間： 2015-03-15
上傳用戶：ccclll
This an adaptive receiver for a direct-sequence spread spectrum (DS-SS) system over an AWGN channel. The adaptive receiver block is modified from the LMS adaptive filter block in DSP Blockset. For DS-SS signal reception, the adaptive filter needs to have multi-rate operation. The input sample rate is equal to CHip rate and the output is at symbol rate. Two rates are related by PG, processing gain
標簽： direct-sequence adaptive receiver spectrum
上傳時間： 2014-01-16
上傳用戶：D&L37
本source code 為s3c4510的bootloader，不同於其他的s3c4510的bootloader，這個bootloader花了很多功夫，完全不需要看data sheet就可以更改register，當週邊CHip改變時，更改bootloader可以很快就完成。只要修改init_gun.h這個文件即可。
標簽： bootloader s3c4510 source code
上傳時間： 2015-03-31
上傳用戶：teddysha
本source code 為s3c4510的bootloader，不同於其他的s3c4510的bootloader，這個bootloader花了很多功夫，完全不需要看data sheet就可以更改register，當週邊CHip改變時，更改bootloader可以很快就完成。只要修改init_gun.h這個文件即可。
標簽： bootloader s3c4510 source code
上傳時間： 2014-11-24
上傳用戶：xieguodong1234
This directory contains the 8051 firmware frameworks source code for the Anchor CHips EZ-USB FX2 CHip.
標簽： frameworks directory the contains
上傳時間： 2014-01-11
上傳用戶：it男一枚
用LPC213X系列的PWM來產生語音。語音數據來源于PC機轉換后得到的。最大可以是16位的。 由于是PWM所以輸出端口需要低通濾波才能夠得到比較干凈的聲音。 可以經過修改使用LPC2132以上的ARM的D/A來產生。 This project outputs audio on PWM0 using wave samples that are stored in the on-CHip Flash ROM.
上傳時間： 2014-11-07
上傳用戶：zhanditian
This project is created using the Keil ARM CA Compiler. The Logic Analyzer built into the simulator may be used to monitor and display any variable or peripheral I/O register. It is already configured to show the PWM output signal on PORT3.0 and PORT3.1 This ARM Example may be debugged using only the uVision Simulator and your PC--no additional hardware or evaluation boards are required. The Simulator provides cycle-accurate simulation of all on-CHip peripherals of the ADuC7000 device series. You may create various input signals like digital pulses, sine waves, sawtooth waves, and square waves using signal functions which you write in C. Signal functions run in the background in the simulator within timing constraints you configure. In this example, several signal functions are defined in the included Startup_SIM.INI file.
標簽： the Analyzer Compiler project
上傳時間： 2013-12-19
上傳用戶：Yukiseop
The project KEIL_IODemo shows how to use memory allocation routines (malloc) and char I/O (printf, scanf) via a serial interface with the Keil ARM toolchain. The I/O functions are adapted for the Analog Devices ADuC7000 series using the SERIAL.C module. The example also shows the efficiency of the Keil CA ARM Compiler run-time library which is tuned for single CHip systems.
標簽： KEIL_IODemo allocation routines project
上傳時間： 2013-12-08
上傳用戶：ve3344
UART I/O and Memory Allocation Example for GNU The project GNU_IODemo shows how to use memory allocation routines (malloc) and char I/O (printf, scanf) via a serial interface with the GNU toolchain. The I/O functions are adapted for the Analog Devices ADuC7000 series using the SERIAL.C module. The example also shows the efficiency of the Keil CA ARM Compiler run-time library which is tuned for single CHip systems.
標簽： Allocation GNU_IODemo Example project
上傳時間： 2015-05-04
上傳用戶：Amygdala
