The C500 microcontroller family usually provides only one on-CHip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the CHip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-CHip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-CHip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
標簽： synchronous Emulating serial
上傳時間： 2014-01-31
上傳用戶：z1191176801
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the CHip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
標簽： Demonstration 3200 USB for
上傳時間： 2014-02-27
上傳用戶：zhangzhenyu
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 Microcontroller Core. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementation of the USB hardware directly on the CHip, complying with the Universal Serial Bus Specification, Revision 1.1.This application note describes a demonstration program that has been written for the DK3200 hardware demonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to work with the device, using the HID class as a ready-made device driver for the USB connection.
上傳時間： 2014-04-03
上傳用戶：lizhizheng88
The P90CL301 is a highly integrated 16/32 bit micro-controller especially suitable for applications requiring lowvoltage and low power consumption. It is fully software compatible with the 68000. Furthermore, it provides bothstandard as well as advanced peripheral functions on-CHip.One of these peripheral functions is the I2C bus. This report describes worked-out driver software (written in C) toprogram the P90CL301 I2C interface. It also contains interface software routines offering the user a quick start inwriting a complete I2C system application.
上傳時間： 2014-01-06
上傳用戶：氣溫達上千萬的
The XA-S3 is a member of Philips Semiconductors’ XA (eXtended Architecture) family of high performance 16-bit single-CHip Microcontrollers. The XA-S3 combines many powerful peripherals on one CHip. Therefore, it is suited for general multipurpose high performance embedded control functions.One of the on-CHip peripherals is the I2C bus interface. This report describes worked-out driver software (written in C) to program / use the I2C interface of the XA-S3. The driver software, together with a demo program and interface software routines offer the user a quick start in writing a complete I2C - XAS3 system application.
上傳時間： 2013-11-10
上傳用戶：liaofamous
提出了一個由AT89C52單片機控制步進電機的實例。可以通過鍵盤輸入相關數據, 并根據需要, 實時對步進電機工作方式進行設置, 具有實時性和交互性的特點。該系統可應用于步進電機控制的大多數場合。實踐表明, 系統性能優于傳統的步進電機控制器。關鍵詞: 單片機; 步進電動機; 直流固態繼電器; 實時控制Con trol System of Stepp ingMotor Ba sed on AT89C52 CHipM icrocomputerMENGWu2sheng, L ILiang (College of Automatization, Northwestern Polytechnical Unversity, Xipan 710072, China)ABSTRACT: A stepp ing motor control system based on AT89C52 CHip microcomputer was described.The data can be inputwith keyboard, and stepp ingmotorwas controlled by these data. According to the demand, users can set the workingmodel of stepp ingmotor in real2time. This system can be widely used in stepp ing motor controlling. The p ractice showed that the performance of this system outdid the tradi tional stepp ing motor controller.KEY WORDS: CHip microcomputer; Stepp ingmotor; DCSSR; Real2time control
標簽： Control System ingMot Stepp
上傳時間： 2013-11-19
上傳用戶：leesuper
The MC68HC05K0 is a low cost, low pin countsingle CHip microcomputer with 504 bytes of userROM and 32 bytes of RAM. The MC68HC05K0 isa member of the 68HC05K series of devices whichare available in 16-pin DIL or SOIC packages.It uses the same CPU as the other devices in the68HC05 family and has the same instructions andregisters. Additionally, the device has a 15-stagemulti-function timer and 10 general purposebi-directional I/0 lines. A mask option is availablefor software programmable pull-downs on all ofthe I/O pins and four of the pins are capable ofgenerating interrupts.The device is ideally suited for remote-controlkeyboard applications because the pull-downs andthe interrupt drivers on the port pins allowkeyboards to be built without any externalcomponents except the keys themselves. There isno need for external pull-up or pull-down resistors,or diodes for wired-OR interrupts, as these featuresare already designed into the device.
上傳時間： 2014-01-24
上傳用戶：zl5712176
用C51寫的普通拼音輸入法源程序代碼:原作使用了一個二維數組用以查表，我認為這樣比較的浪費空間，而且每個字表的索引地址要手工輸入，效率不高。所以我用結構體將其改寫了一下。就是大家現在看到的這個。 因為代碼比較的大，共有6,000多漢字，這樣就得要12,000 byte來存放GB內碼，所以也是沒辦法的.編譯結果約為3000h,因為大部分是索引表，代碼優化幾乎無效。 在Keil C里仿真芯片選用的是華邦的W77E58，它有32k ROM, 256B on-CHip RAM, 1K on-CHip SRAM (用DPTR1指針尋址,相當于有1K的片上xdata)。條件有限，沒有上片試驗，仿真而已。 打算將其移植到AVR上，但CodeAVRC與IAR EC++在結構體、指針的定義使用上似乎與C51不太一樣，現在還未搞定。還希望在這方面有經驗的網友能給予指導。 #include<stdio.h> char * py_ime(char *); void main(void){ while(1) { char input_string[]="yI"; xdata char chinese_string[255]; sprintf(chinese_string,"%s",py_ime(input_string)); }}
上傳時間： 2013-10-30
上傳用戶：cainaifa
基于單片機的汽車多功能報警系統設計The Design of Automobile Multi-function AlarmingBased on Single CHip Computer劉法治趙明富寧睡達(河 南 科 技 學 院 ，新 鄉 453 00 3)摘要介紹了一種基于單片機控制的汽車多功能報警系統，它能對汽車的潤滑系統油壓、制動系統氣壓、冷卻系統溫度、輪胎欠壓及防盜進行自動檢測，并在發現異常情況時，發出聲光報警。闡述了該報警系統的硬件組成及軟件設計方法。關鍵詞單片機傳感器數模轉換報警Abstract Am ulti-fimctiona utomobilea larnungs ystemb asedo ns inglec hipc omputerco ntorlis in torducedin th isp aper.Th eo ilpr essuero flu bricatesystem, air pressure of braking system, temperature of cooling system, under pressure of tyre and guard against theft， detected automaticaly場thesystem. Audio and visual alarms wil be provided under abnormal conditions廠The hardware composition and software design of the system， described.Keywords Singlec hipc omputer Sensor Digital-t-oanaloguec onversion Alarmin 汽車多功能報苦器硬件系統設計根據 系 統 實際需要和產品性價比，選用ATMEL公司新生產的采用CMOs工藝的低功耗、高性能8位單片機AT89S52作為系統的控制器。AT89S52的片內有8k Bytes LSP Flash閃爍存儲器，可進行100(〕次寫、擦除操作;256Bytes內部數據存儲器(RAM);3 2 根可編程輸N輸出線;2個可編程全雙工串行通道;看門狗(WTD)電路等。系統由傳感器、單片機、模數轉換器、無線信號發射電路、指示燈驅動電路、聲光報警驅動電KD一9563，發出三聲二閃光。并觸發一個高電平，驅動無線信號發射電路。
上傳時間： 2013-11-09
上傳用戶：gxmm
隨著 微 電 子技術的飛速發展，電子產品越來越微型化，集成化，自動化，低廉化，進而推動著其它許多產業的發展。特別進人21世紀以來，生物技術與電子技術的結合，成為高科技領域的研究熱點。199()年由瑞士的Manz和Widmer首先提出的“微全分析系統”〔’〕(microto talan alysissy stems，即ptTAS)，通俗地稱為“建在芯片上的實驗室”(Lab on a CHip)或簡稱芯片實驗室(Lab CHip)，主要組成部分為電泳芯片，同時是進樣，分離和檢測為一體的微型裝置，其在電泳實驗中的高效檢測性能為生物化學分析儀器發展提供了一種借鑒。p.TAS廣泛應用于生物醫學、環境檢測、食品衛生、科學以及國防等眾多領域。目前 應 用 的大多為多通道的毛細管電泳芯片，這也是芯片發展的一個必然趨勢。這不僅對電泳芯片本身的設計和制作提出了更高的要求，也對傳感器和數據處理技術提出了新的挑戰。考慮成本，集成度，控制能力以及可靠性方面的因素，本系統采用單片機作為實時數據處理、控制以及通訊的硬件平臺。如果系統中既有實時的通信任務，同時又有其他實時任務，采用一個廉價的單片機，資源會比較緊張，不僅實現困難，結構復雜，而且效果可能不滿意。而采用高性能的處理器，又浪費了其有效資源，所以本系統采用兩個MCU協同工作，以并行/分布式多機的思想，構成了電泳芯 片核心的雙單片機系統結構。微全 分 析 系 統 進行的多項實時任務，可以劃分為以下 幾個模塊:①采集模塊。負責對外圍檢驗設備進行控 制以及對傳送過來的信號進行采集和分析;②交互模 塊。通過液晶顯示，鍵盤掃描，以及打印等實現實驗人 員對前端采集電路的交互操作;③雙單片機控制和通 信模塊。協調雙單片機之間的數據傳輸和指令傳輸 ;④網絡傳輸模塊。其中一個單片機通過以太網發送接 收數據到上位機。本文提出一種實時多任務的雙單片 機控制和通信系統[31的設計，一個MCU基于TCP /IP網絡模塊的實現。
上傳時間： 2013-11-15
上傳用戶：wangdean1101
