Recently a new technology for high voltage Power MOSFETshas been introduced – the CoolMOS™ . Based on thenew device concept of charge compensation the RDS(on) areaproduct for e.g. 600V transistors has been reduced by afactor of 5. The devices show no bipolar current contributionlike the well known tail current observed during the turn-offphase of IGBTs. CoolMOS™ virtually combines the lowswitching losses of a MOSFET with the on-state losses of anIGBT.
標簽： COOLMOS
上傳時間： 2013-11-14
上傳用戶：zhyiroy
With more and more multi-frequency clocks being used in today's chips, especially in the communications field, it is often necessary to switch the source of a clock line while the chip is running.
上傳時間： 2013-10-10
上傳用戶：1214209695
This paper presents a space vector modulation(SVM)-based switching strategy for a three-level neutral point clamped (NPC) converter that is adapted as a STATCOM.
上傳時間： 2013-10-20
上傳用戶：zyt
Many applications require a clock signal to be synchronous, phase-locked, or derived fromanother signal, such as a data signal or another clock. This type of clock circuit is important in
上傳時間： 2014-12-23
上傳用戶：qq21508895
Who has never experienced oscillations issues when using an operational amplifier? Opampsare often used in a simple voltage follower configuration. However, this is not the bestconfiguration in terms of capacitive loading and potential risk of oscillations.Capacitive loads have a big impact on the stability of operational amplifier-basedapplications. Several compensation methods exist to stabilize a standard op-amp. Thisapplication note describes the most common ones, which can be used in most cases.The general theory of each compensation method is explained, and based on this, specific
上傳時間： 2013-10-28
上傳用戶：chenbhdt
Control systems are becoming increasingly dependent on digital processing and so require sensors able to provide direct digital inputs. Sensors based on time measurement, having outputs based on a frequency or phase, have an advantage over conventional analogue sensors in that their outputs can be measured directly in digital systems by pulse counting.
上傳時間： 2013-10-08
上傳用戶：wuyuying
Most circuit designers are familiar with diode dynamiccharacteristics such as charge storage, voltage dependentcapacitance and reverse recovery time. Less commonlyacknowledged and manufacturer specifi ed is diode forwardturn-on time. This parameter describes the timerequired for a diode to turn on and clamp at its forwardvoltage drop. Historically, this extremely short time, unitsof nanoseconds, has been so small that user and vendoralike have essentially ignored it. It is rarely discussed andalmost never specifi ed. Recently, switching regulator clockrate and transition time have become faster, making diodeturn-on time a critical issue. Increased clock rates aremandated to achieve smaller magnetics size; decreasedtransition times somewhat aid overall effi ciency but areprincipally needed to minimize IC heat rise. At clock speedsbeyond about 1MHz, transition time losses are the primarysource of die heating.
上傳時間： 2013-10-10
上傳用戶：誰偷了我的麥兜
Low power operation of electronic apparatus has becomeincreasingly desirable. Medical, remote data acquisition,power monitoring and other applications are good candidatesfor battery driven, low power operation. Micropoweranalog circuits for transducer-based signal conditioningpresent a special class of problems. Although micropowerICs are available, the interconnection of these devices toform a functioning micropower circuit requires care. (SeeBox Sections, “Some Guidelines for Micropower Designand an Example” and “Parasitic Effects of Test Equipmenton Micropower Circuits.”) In particular, trade-offs betweensignal levels and power dissipation become painful whenperformance in the 10-bit to 12-bit area is desirable.
上傳時間： 2013-10-22
上傳用戶：rocketrevenge
使用時鐘PLL的源同步系統時序分析一）回顧源同步時序計算Setup Margin = Min Clock Etch Delay – Max Data Etch Delay – Max Delay Skew – Setup TimeHold Margin = Min Data Etch Delay – Max Clock Etch Delay + Min Delay Skew + Data Rate – Hold Time下面解釋以上公式中各參數的意義：Etch Delay：與常說的飛行時間(Flight Time)意義相同，其值并不是從仿真直接得到，而是通過仿真結果的后處理得來。請看下面圖示：圖一為實際電路，激勵源從輸出端，經過互連到達接收端，傳輸延時如圖示Rmin，Rmax，Fmin，Fmax。圖二為對應輸出端的測試負載電路，測試負載延時如圖示Rising，Falling。通過這兩組值就可以計算得到Etch Delay 的最大和最小值。
上傳時間： 2013-11-05
上傳用戶：VRMMO
The equal-area theorem●This is sinusoidal PWM (SPWM)●The equal-area theorem can be appliedto realize any shape of waveforms ●Natural sampling●Calculation based on equal-area criterion●Selected harmonic elimination●Regular sampling●Hysteresis-band control●Triangular wave comparison withfeedback control
上傳時間： 2013-11-22
上傳用戶：linyao
