Radio Frequency Integrated Circuit Design I enjoyed reading this book for a number of reasons. One reason is that itaddresses high-speed analog design in the context of microwave issues. This isan advanced-level book, which should follow courses in basic circuits andtransmission lines. Most analog integrated circuit designers in the past workedon applications at low enough frequency that microwave issues did not arise.As a consequence, they were adept at lumped parameter circuits and often notcomfortable with circuits where waves travel in space. However, in order todesign radio frequency (RF) communications integrated circuits (IC) in thegigahertz range, one must deal with transmission lines at chip interfaces andwhere interconnections on chip are far apart. Also, impedance matching isaddressed, which is a topic that arises most often in microwave circuits. In mycareer, there has been a gap in comprehension between analog low-frequencydesigners and microwave designers. Often, similar issues were dealt with in twodifferent languages. Although this book is more firmly based in lumped-elementanalog circuit design, it is nice to see that microwave knowledge is brought inwhere necessary.Too many analog circuit books in the past have concentrated first on thecircuit side rather than on basic theory behind their application in communications.The circuits usually used have evolved through experience, without asatisfying intellectual theme in describing them. Why a given circuit works bestcan be subtle, and often these circuits are chosen only through experience. Forthis reason, I am happy that the book begins first with topics that require anintellectual approach—noise, linearity and filtering, and technology issues. Iam particularly happy with how linearity is introduced (power series). In therest of the book it is then shown, with specific circuits and numerical examples,how linearity and noise issues arise.
上傳時間： 2014-12-23
上傳用戶：han_zh
數字與模擬電路設計技巧IC與LSI的功能大幅提升使得高壓電路與電力電路除外，幾乎所有的電路都是由半導體組件所構成，雖然半導體組件高速、高頻化時會有EMI的困擾，不過為了充分發揮半導體組件應有的性能，電路板設計與封裝技術仍具有決定性的影響。 模擬與數字技術的融合由于IC與LSI半導體本身的高速化，同時為了使機器達到正常動作的目的，因此技術上的跨越競爭越來越激烈。雖然構成系統的電路未必有clock設計，但是毫無疑問的是系統的可靠度是建立在電子組件的選用、封裝技術、電路設計與成本，以及如何防止噪訊的產生與噪訊外漏等綜合考慮。機器小型化、高速化、多功能化使得低頻/高頻、大功率信號/小功率信號、高輸出阻抗/低輸出阻抗、大電流/小電流、模擬/數字電路，經常出現在同一個高封裝密度電路板，設計者身處如此的環境必需面對前所未有的設計思維挑戰，例如高穩定性電路與吵雜(noisy)性電路為鄰時，如果未將噪訊入侵高穩定性電路的對策視為設計重點，事后反復的設計變更往往成為無解的夢魘。模擬電路與高速數字電路混合設計也是如此，假設微小模擬信號增幅后再將full scale 5V的模擬信號，利用10bit A/D轉換器轉換成數字信號，由于分割幅寬祇有4.9mV，因此要正確讀取該電壓level并非易事，結果造成10bit以上的A/D轉換器面臨無法順利運作的窘境。另一典型實例是使用示波器量測某數字電路基板兩點相隔10cm的ground電位，理論上ground電位應該是零，然而實際上卻可觀測到4.9mV數倍甚至數十倍的脈沖噪訊(pulse noise)，如果該電位差是由模擬與數字混合電路的grand所造成的話，要測得4.9 mV的信號根本是不可能的事情，也就是說為了使模擬與數字混合電路順利動作，必需在封裝與電路設計有相對的對策，尤其是數字電路switching時，ground vance noise不會入侵analogue ground的防護對策，同時還需充分檢討各電路產生的電流回路(route)與電流大小，依此結果排除各種可能的干擾因素。以上介紹的實例都是設計模擬與數字混合電路時經常遇到的瓶頸，如果是設計12bit以上A/D轉換器時，它的困難度會更加復雜。
上傳時間： 2013-11-16
上傳用戶：731140412
LAYOUT REPORT .............. 1 目錄.................. 1 1. PCB LAYOUT 術語解釋(TERMS)......... 2 2. Test Point : ATE 測試點供工廠ICT 測試治具使用............ 2 3. 基準點 (光學點) -for SMD:........... 4 4. 標記 (LABEL ING)......... 5 5. VIA HOLE PAD................. 5 6. PCB Layer 排列方式...... 5 7.零件佈置注意事項 (PLACEMENT NOTES)............... 5 8. PCB LAYOUT 設計............ 6 9. Transmission Line ( 傳輸線 )..... 8 10.General Guidelines – 跨Plane.. 8 11. General Guidelines – 繞線....... 9 12. General Guidelines – Damping Resistor. 10 13. General Guidelines - RJ45 to Transformer................. 10 14. Clock Routing Guideline........... 12 15. OSC & CRYSTAL Guideline........... 12 16. CPU
上傳時間： 2013-12-20
上傳用戶：康郎
Integrated EMI/Thermal Design forSwitching Power SuppliesWei ZhangThesis submitted to the Faculty of theVirginia Polytechnic Institute and State Universityin partial fulfillment of the requirements for the degree of Integrated EMI/Thermal Design forSwitching Power SuppliesWei Zhang(ABSTRACT)This work presents the modeling and analysis of EMI and thermal performancefor switch power supply by using the CAD tools. The methodology and design guidelinesare developed.By using a boost PFC circuit as an example, an equivalent circuit model is builtfor EMI noise prediction and analysis. The parasitic elements of circuit layout andcomponents are extracted analytically or by using CAD tools. Based on the model, circuitlayout and magnetic component design are modified to minimize circuit EMI. EMI filtercan be designed at an early stage without prototype implementation.In the second part, thermal analyses are conducted for the circuit by using thesoftware Flotherm, which includes the mechanism of conduction, convection andradiation. Thermal models are built for the components. Thermal performance of thecircuit and the temperature profile of components are predicted. Improved thermalmanagement and winding arrangement are investigated to reduce temperature.In the third part, several circuit layouts and inductor design examples are checkedfrom both the EMI and thermal point of view. Insightful information is obtained.
上傳時間： 2013-11-10
上傳用戶：1595690
Power over Ethernet (PoE) is a new development thatallows for the delivery of power to Ethernet-based devicesvia standard Ethernet CAT5 cable, precluding the need forwall adapters or other external power sources. The PoEspecification defines a hardware detection protocol wherePower Sourcing Equipment (PSE) is able to identify PoEPowered Devices (PDs), thus allowing full backwardscompatibility with non-PoE-aware (legacy) Ethernetdevices.
上傳時間： 2013-11-11
上傳用戶：daoyue
高的工作電壓高達100V N雙N溝道MOSFET同步驅動 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
上傳時間： 2013-10-24
上傳用戶：wd450412225
Although recent popular attention is focused on LithiumIon batteries, one must not forget that other batterychemistries, such as Nickel Cadmium (NiCd) and NickelMetal Hydride (NiMH) have advantages in rechargeablepower systems. Nickel-based batteries are robust, capableof high discharge rates, have good cycle life, do notrequire special protection circuitry and are less expensivethan Li-Ion. Among the two, NiMH batteries are rapidlyreplacing NiCd because of their higher capacity (40% to50% more) and the environmental concerns of the toxiccadmium contained in NiCd batteries.
上傳時間： 2013-11-04
上傳用戶：qq10538412
As the performance of many handheld devices approachesthat of laptop computers, design complexity also increases.Chief among them is thermal management—how doyou meet increasing performance demands while keepinga compact and small product cool in the user’s hand?For instance, as battery capacities inevitably increase,charge currents will also increase to maintain or improvetheir charge times. Traditional linear regulator-based batterychargers will not be able to meet the charge currentand effi ciency demands necessary to allow a product torun cool. What is needed is a switching-based chargerthat takes just about the same amount of space as a linearsolution—but without the heat.
上傳時間： 2013-11-23
上傳用戶：lu2767
為了改變目前電網現場作業管理的變電巡檢、變電檢修試驗、輸電線路巡檢檢修等管理系統各自獨立運行，信息不能共享，功能、效率受限，建設和維護成本高的現狀，提出了采用B/S+C/S構架模式，將各現場作業管理模塊和生產MIS（管理系統）集成為一體的現場作業管理系統的設計方案，做到各子系統和生產MIS軟硬資源共享，做到同一數據唯一入口、一處錄入多處使用。各子系統設備人員等基礎信息來源于生產管理系統，各子系統又是生產管理系統的作業數據、缺陷信息的重要來源。經過研究試用成功和推廣應用，目前該系統已在江西電網220 kV及以上變電站全面應用。 Abstract: In order to improve the status that the substation field inspection system， substation equipments maintenance and testing system， power-line inspection and maintenance system are running independent with each other. They can?蒺t share the resource information which accordingly constrains their functions and efficiency， and their construction and maintenance costs are high. This paper introduces a field standardized work management system based on B/S+C/S mode， integrating all field work management systems based on MIS and share the equipments and employee?蒺s data of MIS，the field work data of the sub systems are the source information of MIS， by which the same single data resouce with one-time input can be utilized in multiple places. After the research and testing， this system is triumphantly using in all 220kV and above substations in Jiangxi grid.
上傳時間： 2013-11-15
上傳用戶：han_zh
為解決直流逆變交流的問題，有效地利用能源，讓電源輸出最大功率，設計了高性能的基于IR2101最大功率跟蹤逆變器，并以SPMC75F2413A單片機作為主控制器。高電壓、高速功率的MOSFET或IGBT驅動器IR2101采用高度集成的電平轉換技術，同時上管采用外部自舉電容上電，能夠穩定高效地驅動MOS管。該逆變器可以實現DC/AC的轉換，最大功率點的跟蹤等功能。實際測試結果表明，該逆變器系統具有跟蹤能力強，穩定性高，反應靈敏等特點，該逆變器不僅可應用于普通的電源逆變系統，而且可應用于光伏并網發電的逆變系統，具有廣泛的市場前景。 Abstract: To solve the problem of DC-AC inverter， and to utilize solar energy more efficiently， the design of maximum power point tracking inverter based on IR2101 was achieved with a high-performance， which can make the system output power maximum. SPMC75F2413A was adopted as main controller. IR2101 is a high voltage， high speed power MOSFET and IGBT driver. It adopted highly integrated voltage level transforming technology， and an external bootstrap capacitor was used， which could drive MOS tube efficiently and stably. Many functions are achieved in the system， such as DC/AC conversion， maximun power point tracking， etc. The actual test result shows that the inverter system has characteristics of strong tracking ability， high stability and reacting quickly. The design can not only be used in ordinary power inverter system， but also be used in photovoltaic power inverter system. The design has certain marketing prospects
上傳時間： 2013-11-17
上傳用戶：lliuhhui
