為降低成本和解決現有膜片鉗放大器系統中PC機的干擾問題，研究了一種基于單片機的膜片鉗放大器小系統。該系統采用ADI公司生產的ADuC841作為控制核心，并且配置相應的液晶顯示模塊LCM3202401。模擬電路部分采用高輸入阻抗的AD8627實現微電流信號的采集，并由后級電路進行信號的放大和電阻電容的補償。它具有硬件電路簡單、體積小、使用方便的特點。既可以單獨作為小系統實現采集和顯示，也可以通過紅外方式和PC機進行通訊，在PC機上進行信號的處理。 Abstract: In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on microcontroller is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control core in the system, configuring a liquid crystal module LCM3202401. In the analog circuit, AD8627 with high input impedance is used to detect the low current，signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient operation. It can either be used as an independent system to measure and show signal detected or transmit to PC by infrared ray.
上傳時間： 2013-11-06
上傳用戶：yy_cn
為解決輸油管道溫度壓力參數實時監測的問題，設計了以C8051F930單片機作為控制核心的超低功耗輸油管道溫度壓力遠程監測系統。現場儀表使用高精度電橋采集數據，通過433 MHz短距離無線通信網絡與遠程終端RTU進行通信，RTU通過GPRS網絡與PC上位機進行遠程數據傳輸，在上位機中實現數據存儲和圖形化界面顯示，從而實現輸油管道溫度壓力參數的實時監測和異常報警。經實驗證明，該系統的12位數據采集精度滿足設計要求，漏碼率小于1%，正常工作時間超過5個月，能實時有效地監測輸油管道的溫度壓力參數，節省大量人工成本，有效預防管道參數異常造成的經濟損失和環境污染。 Abstract: In order to solve the problems on real-time monitoring of pipeline temperature and pressure parameters， the ultra-low power remote pipeline temperature and pressure monitoring system was designed by using the single chip processor C8051F930 as the control core. The high-precision electric bridge was used in field instruments for data collection， the 433MHz short-range wireless communication network was used to make communication between field instrument and RTU， the GPRS was used by the RTU to transmit data to the PC host computer， and the data was stored and displayed in the PC host computer， so the real-time monitoring and exception alerts of pipeline temperature and pressure parameters were achieved. The experiment proves that the system of which error rate is less than 1% over five months working with the 12-bit data acquisition accuracy can effectively monitor the pipeline temperature and pressure parameters in real time， it saves a lot of labor costs and effectively prevents environmental pollution and economic losses caused by abnormal channel parameters.
上傳時間： 2013-11-07
上傳用戶：cuibaigao
針對當前安檢力學試驗機所能完成的試驗種類單一、自動化程度低等問題，提出一種以ATmega128單片機為核心控制器的安檢力學試驗機的設計。詳細闡述了該安檢力學試驗機各個組成部分的設計原理和方案，并且給出了各部分的軟件設計思想和操作流程。經過大量測試試驗表明：設計的安檢力學試驗機可以完成多達十余種的力學安檢試驗，完全符合相關國家標準，并且具有數據采集精度高、傳輸速度快、操作安全簡便等特點，實現了安檢設備的多功能化、數字化和自動化。 Abstract: Currently， many mechanical security testing machines have only one function. The degree of automation of them is low. To solve those problems， a new kind of mechanical security testing machine， using ATmega128 micro-controller as its core controller， has been advanced. It describes the components of the machine. The principles and the scheme in the designing processes are presented in detail， and the software architecture and the operation processes of each part are given. After having done many testing， we have reached the following conclusions: the mechanical security testing machine presented can do over ten mechanical security tests complying with related national standards. It has high data acquisition accuracy and high transmission speed. The operation of the machine is simple and safe. In general， this machine is a multi-functional， highly automatic， digitalized security testing device.
上傳時間： 2013-11-05
上傳用戶：a67818601
AVR mega128開發板 聯系 楊迪 15336417867 0531-55508458 QQ：1347978253 http://www.easyele.cn 產品概述:AVR mega128開發板是AVRVi開發的基于Atmega128單片機的綜合學習開發系統，板載學習資源，集成JTAG仿真器和ISP下載功能，核心板可拆卸獨立使用，是你學習AVR單片機，參加各類電子設計競賽，快速搭建產品的不二選擇。AVR mega128開發板亦可以作為單片機培訓，高校實驗室，課程設計等的實驗器材。為了更好的支持客戶的學習和開發，此開發板板通訊接口升級為USB接口，方便計算機沒有串口的朋友，學習起來更加簡捷。貨號：EasyAVRM128SK-A 規格： 套 重量：300克 單價498/套。 參數特色： 1.采用核心板和主板分離的形式，在系統的學習之后，可以把核心板直接用于產品中，快速搭建系統。 2.開發板上集成了AVR JTAG ICE仿真器和AVR ISP編程器，超高性價比。 3.您只需要再擁有一臺計算機，而不需要購買仿真器和編程器就可以學習開發了。 4.信號調理電路，輸入0～10V，軌至軌信號調理。 5.系統資源適中，性價比高。 6.豐富的學習資源，完善的產品支持。 7.EasyAVR教給你從開發環境建立，軟件編譯，到下載，傳真，硬件設計等一系列電子工程師必備的技能，真正學以致用。 AVR mega128開發板板上資源： M128 所有引腳引出，可以利用杜邦頭很方便的進行接插擴展，標準2.54針距，可以直接插在萬用板上使用，便于進行實驗 m128 DB Core 自帶5V、3V3 雙路電源穩壓 m128 DB Core 外部晶振多種選擇，既可以使用板上已經焊接好的14.7456M的晶振，也可以自己根據自己的需求擴展，晶振的切換通過跳線實現m128 DB Core 帶有JTAG ISP 標準接口 m128 DB Core 自帶一路標準RS232－TTL轉換電路，方便實現串口通信 AVR mega128 開發板底板：板載JTAG 仿真器 板載STK500 下載內核 2路獨立可調的信號調理電路，可控增益G=0.1-10 2路RS232 串行接口 1路RS485 接口 8 路LED 顯示 4 位動態7 段數碼管，利用74HC595進行驅動 4 位獨立按鍵 板載IIC 總線PCF8563 實時鐘芯片 板載IIC 總線EEPROM AT24c01 1 路有源蜂鳴器 1 路18B20 溫度傳感器接口，支持單總線器件。(12820可選：10元每個) 1602LCD 接口(送1602液晶) 12232、12864 LCD 接口(LCD12864可選：80元每個) 想找一份好工作嗎？ 你想成為一名電子設計工程師嗎？ 你對電子設計有濃厚興趣，而沒有工具嗎？ 看了很久的程序方面的書籍，卻沒有實踐的機會嗎？ 需要開發產品，想快速入門？ 想參加電子設計大賽，機器人大賽嗎？ 這個性價比高的專業工具是你的不二選擇，它不僅僅是一個AVR mega128 開發板，他還是一個強大的開發工具，通過它進行學習后，對電子產品的設計有進一步的認知，建立起學習ARM，DSP，FPGA的良好基礎。AVR mega128 開發板集成了AVR學習板，AVR開發板，AVR編程器，AVR仿真器，AVR核心板的功能，并且可以分開獨立使用。 銷售清單： 1、調試好的AVR mega128開發板一塊(板載JTAG ISP 二合一，已經寫入自檢程序) 2、ATmega128核心板一塊 3、USB供電線一條 4、標準串口(RS232)通訊線纜一條 5、資料光盤一張 6、使用說明書（實驗講義）一本 7、保修卡即訂單清單一份 8、贈送LCD1602液晶一塊
上傳時間： 2013-11-10
上傳用戶：zm7516678
NXP Semiconductor designed the LPC2400 microcontrollers around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded Trace. The LPC2400 microcontrollers have 512 kB of on-chip high-speedFlash memory. This Flash memory includes a special 128-bit wide memory interface andaccelerator architecture that enables the CPU to execute sequential instructions fromFlash memory at the maximum 72 MHz system clock rate. This feature is available onlyon the LPC2000 ARM Microcontroller family of products. The LPC2400 can execute both32-bit ARM and 16-bit Thumb instructions. Support for the two Instruction Sets meansEngineers can choose to optimize their application for either performance or code size atthe sub-routine level. When the core executes instructions in Thumb state it can reducecode size by more than 30 % with only a small loss in performance while executinginstructions in ARM state maximizes core performance.
上傳時間： 2013-11-15
上傳用戶：zouxinwang
NEC 16位MCU參考手冊 The 78K0R/IC3 is a 16-bit single-chip microcontroller that uses a 78K0R CPU core and incorporates peripheral functions, such as ROM/RAM, a multi-function timer, a multi-function serial interface, an A/D converter, a programmable gain amplifier (PGA), a comparator, a real-time counter, and a watchdog timer.
上傳時間： 2013-11-02
上傳用戶：努力努力再努力
The LPC1769/68/67/66/65/64 are ARM Cortex-M3 based microcontrollers for embedded applications featuring a high level of integration and low power consumption. The ARM Cortex-M3 is a next generation core that offers system enhancements such as enhanced debug features and a higher level of support block integration.
上傳時間： 2014-02-20
上傳用戶：13215175592
MC9S08QG8英文資料 The MC9S08QG8 is the newest member of the Freescale 8-bit family of highly integratedmicrocontrollers, based on the high-performance yet low power HCS08 core. The MC9S08QG8is an excellent solution for power-sensitive applications with extended battery life and maximum performance down to 1.8VDC.
上傳時間： 2014-12-28
上傳用戶：dxxx
世界著名廠家單片機簡介1.Motorola 單片機:Motorola是世界上最大的單片機廠商,品種全,選擇余地大,新產品多,在8位機方面有68HC05和升級產品68HC08,68HC05有30多個系列200多個品種,產量超過20億片.8位增強型單片機68HC11也有30多個品種,年產量1億片以上,升級產品有68HC12.16位單片機68HC16也有十多個品種.32位單片機683XX系列也有幾十個品種.近年來以PowerPC,Codfire,M.CORE等作為CPU,用DSP作為輔助模塊集成的單片機也紛紛推出,目前仍是單片機的首選品牌.Motorola單片機特點之一是在同樣的速度下所用的時鐘較Intel類單片機低的多因而使得高頻噪聲低,抗干擾能力強,更適合用于工控領域以及惡劣環境.Motorola 8位單片機過去策略是掩膜為主,最近推出OTP計劃以適應單片機的發展,在32位機上,M.CORE在性能和功耗上都勝過ARM7.2.Microchip 單片機:Microchip 單片機是市場份額增長最快的單片機.他的主要產品是16C系列8位單片機,CPU采用RISC結構,僅33條指令,運行速度快,且以低價位著稱,一般單片機價格都在1美元以下.Microchip 單片機沒有掩膜產品,全部都是OTP器件(現已推出FLASH型單片機).Microchip強調節約成本的最優化設計,是使用量大,檔次低,價格敏感的產品.3.Scenix單片機:Scenix單片機的I/O模塊最有創意.I/O模塊的集成與組合技術是單片機技術不可缺少的重要方面.除傳統的I/O功能模塊如并行I/O,URT,SPI,I2C,A/D,PWM,PLL,DTMF等,新的I/O模塊不斷出現,如USB,CAN,J1850,最具代表的是Motorola 32位單片機,它集成了包括各種通信協議在內的I/O模塊,而Scenix單片機在I/O模塊的處理上引入了虛擬I/O的概念. Scenix單片機采用了RISC結構的CPU,使CPU最高工作頻率達50MHz.運算速度接近50MIPS.有了強有力的CPU,各種I/O功能便可以用軟件的辦法模擬.單片機的封裝采用20/28引腳.公司提供各種I/O的庫函數,用于實現各種I/O模塊的功能.這些軟件完成的模塊包括多路UART,多種A/D,PWM,SPI,DTMF,FSK,LCD驅動等,這些都是通常用硬件實現起來相當復雜的模塊.4.NEC單片機:NEC單片機自成體系,以8位機78K系列產量最高,也有16位,32位單片機.16位單片機采用內部倍頻技術,以降低外時鐘頻率.有的單片機采用內置操作系統.NEC的銷售策略注重服務大客戶,并投入相當大的技術力量幫助大客戶開發新產品.5.東芝單片機:東芝單片機從4位倒64位,門類齊全.4位機在家電領域仍有較大市場.8位機主要有870系列,90系列等.該類單片機允許使用慢模式,采用32KHz時鐘功耗低至10uA數量級.CPU內部多組寄存器的使用,使得中斷響應與處理更加快捷.東芝公司的32位機采用MIPS3000 ARISC的CPU結構,面向VCD,數字相機,圖象處理市場.6.富士通單片機:富士通也有8位,16位和32位單片機,但是8位機使用的是16位的CPU內核.也就是說8位機與16位機指令相同,使得開發比較容易.8位機有名是MB8900系列,16位機有MB90系列.富士通注重服務大公司,大客戶,幫助大客戶開發產品.7.Epson 單片機:Epson公司以擅長制造液晶顯示器著稱,故Epson單片機主要為該公司生產的LCD配套.其單片機的LCD驅動做的特別好.在低電壓,低功耗方面也很有特色.目前0.9V供電的單片機已經上市,不久LCD顯示手表將使用0.5V供電.
上傳時間： 2014-12-28
上傳用戶：leyesome
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
標簽： Demonstration 3200 USB for
上傳時間： 2014-02-27
上傳用戶：zhangzhenyu
