微電腦型RS-485顯示電表（24*48mm/48*96mm） 特點： 5位數RS-485顯示電表 顯示范圍-19999-99999位數 通訊協議Modbus RTU模式 寬范圍交直流兩用電源設計 尺寸小,穩定性高 主要規格： 顯示范圍:-19999~99999 digit RS-485傳輸速度: 19200/9600/4800/2400 selective RS-485通訊位址: "01"-"FF" RS-485通訊協議: Modbus RTU mode 顯示幕: Red high efficiency LEDs high 10.16 mm (0.4") (MMX-RS-11X) Red high efficiency LEDs high 20.32 mm (0.8") (MMX-RS-12X) Red high efficiency LEDs high 10.16 mm (0.4")x2 (MMX-RS-22X) 參數設定方式: Touch switches 記憶方式: Non-volatile E²PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/power) 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上傳時間： 2015-01-03
上傳用戶：feitian920
微電腦型單相交流集合式電表（單相二線系統） 特點： 精確度0.25%滿刻度±1位數 可同時量測與顯示交流電壓,電流,頻率,瓦特,(功率因數/視在功率) 交流電壓,電流,瓦特皆為真正有效值(TRMS) 交流電流,瓦特之小數點可任意設定 瓦特單位W或KW可任意設定 CT比可任意設定(1至999) 輸入與輸出絕緣耐壓 2仟伏特/1分鐘( 突波測試強度4仟伏特(1.2x50us) 數位RS-485界面 (Optional) 主要規格： 精確度: 0.1% F.S.±1 digit (Frequency) 0.25% F.S.±1 digit(ACA,ACV,Watt,VA) 0.25% F.S. ±0.25o(Power Factor) (-.300~+.300) 輸入負載: <0.2VA (Voltage) <0.2VA (Current) 最大過載能力: Current related input: 3 x rated continuous 10 x rated 30 sec. 25 x rated 3sec. 50 x rated 1sec. Voltage related input: maximum 2 x rated continuous 過載顯示: "doFL" 顯示值范圍: 0~600.0V(Voltage) 0~999.9Hz(Frequency)(<20% for voltage input) 0~19999 digit adjustable(Current,Watt,VA) 取樣時間: 2 cycles/sec. RS-485通訊位址: "01"-"FF" RS-485傳輸速度: 19200/9600/4800/2400 selective RS-485通信協議: Modbus RTU mode 溫度系數: 100ppm/℃ (0-50℃) 顯示幕: Red high efficiency LEDs high 10.16 mm(0.4") 參數設定方式: Touch switches 記憶型式: Non-volatile E²PROM memory 絕緣抗阻: >100Mohm with 500V DC 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600 Vdc (input/output) 突波測試: ANSI c37.90a/1974,DIN-IEC 255-4 impulse voltage 4KV(1.2x50us) 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上傳時間： 2015-01-03
上傳用戶：幾何公差
特點： 精確度0.25%滿刻度±1位數 可量測交流瓦特/乏爾/功率因數/相角 顯示范圍0- ±19999可任意規劃 輸入與輸出絕緣耐壓2仟伏特/1分鐘(input/output/power)) 突波測試強度4仟伏特(1.2x50us) 2組警報功能 (Optional) 15BIT類比輸出功能 (Optional) 數位RS-485界面 (Optional)
上傳時間： 2013-11-08
上傳用戶：330402686
Abstract: Many modern industrial, medical, and commercial applications require temperature measurements in the extended temperature rangewith accuracies of ±0.3°C or better, performed with reasonable cost and often with low power consumption. This article explains how platinumresistance temperature detectors (PRTDs) can perform measurements over wide temperature ranges of -200°C to +850°C, with absolute accuracyand repeatability better than ±0.3°C, when used with modern processors capable of resolving nonlinear mathematical equation quickly and costeffectively. This article is the second installment of a series on PRTDs. For the first installment, please read application note 4875, "High-Accuracy Temperature Measurements Call for Platinum Resistance Temperature Detectors (PRTDs) and Precision Delta-Sigma ADCs."
上傳時間： 2013-11-06
上傳用戶：WMC_geophy
Modern electronic systems solve so many difficult problems that they often seem like magic. Nonetheless, these systems all have thesame basic limitation: they need a source of electrical power! Most of the time this is a straightforward challenge for the electronicdesigner, because there are many power-delivery solutions. Yet sometimes a device has no direct power source, and running wiresor replacing batteries is impractical. Even when long-life batteries are usable, they eventually need to be replaced, which requires aservice call.
標簽： 能量收集
上傳時間： 2015-01-03
上傳用戶：zukfu
因為測量系統都用50歐姆, 如非特指, 以下所說的Gain均指功率增益(Power Gain). 但是一般的接收機的輸入輸出并非50歐姆, 因此有必要考慮電壓增益(Voltage Gain).
上傳時間： 2015-01-03
上傳用戶：1318695663
Have you had the exasperating experience of a laptop orPDA defi antly not responding to your commands? Youfrantically press key after key, but to no avail. As hopeturns to anger (but just before you throw the company’slaptop through the window) you slam your fi nger againstthe on/off power button. Ten seconds later, your laptopfi nally surrenders and the screen goes black in a highpitched whimper.
上傳時間： 2013-12-10
上傳用戶：Vici
ACPR (adjacent channel power ratio), AltCPR (alternatechannel power ratio), and noise are important performancemetrics for digital communication systems thatuse, for example, WCDMA (wideband code division multipleaccess) modulation. ACPR and AltCPR are bothmeasures of spectral regrowth. The power in the WCDMAcarrier is measured using a 5MHz measurement bandwidth;see Figure 1. In the case of ACPR, the total powerin a 3.84MHz bandwidth centered at 5MHz (the carrierspacing) away from the center of the outermost carrier ismeasured and compared to the carrier power. The resultis expressed in dBc. For AltCPR, the procedure is thesame, except we center the measurement 10MHz awayfrom the center of the outermost carrier.
上傳時間： 2013-11-02
上傳用戶：maricle
Frequently, voltage reference stability and noise defi nemeasurement limits in instrumentation systems. In particular,reference noise often sets stable resolution limits.Reference voltages have decreased with the continuingdrop in system power supply voltages, making referencenoise increasingly important. The compressed signalprocessing range mandates a commensurate reductionin reference noise to maintain resolution. Noise ultimatelytranslates into quantization uncertainty in A to D converters,introducing jitter in applications such as scales, inertialnavigation systems, infrared thermography, DVMs andmedical imaging apparatus. A new low voltage reference,the LTC6655, has only 0.3ppm (775nV) noise at 2.5VOUT.Figure 1 lists salient specifi cations in tabular form. Accuracyand temperature coeffi cient are characteristic ofhigh grade, low voltage references. 0.1Hz to 10Hz noise,particularly noteworthy, is unequalled by any low voltageelectronic reference.
上傳時間： 2013-10-30
上傳用戶：wxhwjf
在Multisim 10軟件環境下，設計一種由運算放大器構成的精確可控矩形波信號發生器，結合系統電路原理圖重點闡述了各參數指標的實現與測試方法。通過改變RC電路的電容充、放電路徑和時間常數實現了占空比和頻率的調節，通過多路開關投入不同數值的電容實現了頻段的調節，通過電壓取樣和同相放大電路實現了輸出電壓幅值的調節并提高了電路的帶負載能力，可作為頻率和幅值可調的方波信號發生器。Multisim 10仿真分析及應用電路測試結果表明，電路性能指標達到了設計要求。 Abstract: Based on Multisim 10， this paper designed a kind of rectangular-wave signal generator which could be controlled exactly composed of operational amplifier， the key point was how to implement and test the parameter indicators based on the circuit diagram. The duty and the frequency were adjusted by changing the time constant and the way of charging and discharging of the capacitor， the width of frequency was adjusted by using different capacitors provided with multiple switch， the amplitude of output voltage was adjusted by sampling voltage and using in-phase amplifier circuit，the ability of driving loads was raised， the circuit can be used as squarewave signal generator whose frequency and amplitude can be adjusted. The final simulation results of Multisim 10 and the tests of applicable circuit show that the performance indicators of the circuit meets the design requirements.
上傳時間： 2014-01-21
上傳用戶：shen007yue
