12bit 低功耗DAC 數模轉換器
The MAX5302 combines a low-power, voltage-output,
12-bit digital-to-analog Converter (DAC) and a precision
output amplifier in an 8-pin μMAX package. It operates
from a single +5V supply, drawing less than 280μA of
supply current.
The AP2406 is a 1.5Mhz constant frequency, slope compensated current mode PWM step-down Converter. The device integrates a main switch and a synchronous rectifier for high efficiency without an external Schottky diode. It is ideal for powering portable equipment that runs from a single cell lithium-Ion (Li+) battery. The AP2406 can supply 600mA of load current from a 2.5V to 5.5V input voltage. The output voltage can be regulated as low as 0.6V. The AP2406 can also run at 100% duty cycle for low dropout operation, extending battery life in portable system. Idle mode operation at light loads provides very low output ripple voltage for noise sensitive applications.
The AP2406 is offered in a low profile (1mm) 5-pin, thin SOT package, and is available in an adjustable version and fixed output voltage of 1.2V, 1.5V and 1.8V
DESCRIPTION
The Texas Instruments MSP430 family of ultra-low-power microcontrollers consists of several devices featuring
different sets of peripherals targeted for various applications. The architecture, combined with five low-power
modes, is optimized to achieve extended battery life in portable measurement applications. The device features a
powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency.
The digitally controlled oscillator (DCO) allows wake-up from low-power modes to active mode in less than 1 μs.
The MSP430G2x13 and MSP430G2x53 series are ultra-low-power mixed signal microcontrollers with built-in 16-
bit timers, up to 24 I/O capacitive-touch enabled pins, a versatile analog comparator, and built-in communication
capability using the universal serial communication interface. In addition the MSP430G2x53 family members
have a 10-bit analog-to-digital (A/D) Converter. For configuration details see Table 1.
Typical applications include low-cost sensor systems that capture analog signals, convert them to digital values,
and then process the data for display or for transmission to a host system.
基于TMS320F2812 光伏并網發電模擬裝置PROTEL設計原理圖+PCB+軟件源碼+WORD論文文檔,硬件采用2層板設計，PROTEL99SE 設計的工程文件，包括完整的原理圖和PCB文件，可以做為你的學習設計參考。 摘要：本文實現了一個基于TMS320F2812 DSP芯片的光伏并網發電模擬裝置，采用直流穩壓源和滑動變阻器來模擬光伏電池。通過TMS320F2812 DSP芯片ADC模塊實時采樣模擬電網電壓的正弦參考信號、光伏電池輸出電壓、負載電壓電流反饋信號等。經過數據處理后，用PWM模塊產生實時的SPWM 波，控制MOSFET逆變?nèi)珮蜉敵稣也ā１疚挠肞I控制算法實現了輸出信號對給定模擬電網電壓的正弦參考信號的頻率和相位跟蹤，用恒定電壓法實現了光伏電池最大功率點跟蹤（MPPT），從而達到模擬并網的效果。另外本裝置還實現了光伏電池輸出欠壓、負載過流保護功能以及光伏電池輸出欠壓、過流保護自恢復功能、聲光報警功能、孤島效應的檢測、保護與自恢復功能。系統測試結果表明本設計完全滿定設計要求。關鍵詞：光伏并網，MPPT，DSP Photovoltaic Grid-connected generation simulator Zhangyuxin，Tantiancheng，Xiewuyang(College of Electrical Engineering, Chongqing University)Abstract: This paper presents a photovoltaic grid-connected generation simulator which is based on TMS320F2812 DSP, with a DC voltage source and a variable resistor to simulate the characteristic of photovoltaic cells. We use the internal AD Converter to real-time sampling the referenced grid voltage signal, outputting voltage of photovoltaic, feedback outputting voltage and current signal. The PWM module generates SVPWM according to the calculation of the real-time sampling data, to control the full MOSFET inverter bridge output sine wave. We realized that the output voltage of the simulator can track the frequency and phase of the referenced grid voltage with PI regulation, and the maximum photovoltaic power tracking with constant voltage regulation, thereby achieved the purpose of grid-connected simulation. Additionally, this device has the over-voltage and over-current protection, audible and visual alarm, islanding detecting and protection, and it can recover automatically. The testing shows that our design is feasible.Keywords: Photovoltaic Grid-connected，MPPT，DSP 目錄引言 11. 方案論證 11.1. 總體介紹 11.2. 光伏電池模擬裝置 11.3. DC-AC逆變橋 11.4. MOSFET驅動電路方案 21.5. 逆變電路的變頻控制方案 22. 理論分析與計算 22.1. SPWM產生 22.1.1. 規則采樣法 22.1.2. SPWM 脈沖的計算公式 32.1.3. SPWM 脈沖計算公式中的參數計算 32.1.4. TMS320F2812 DSP控制器的事件管理單元 42.1.5. 軟件設計方法 62.2. MPPT的控制方法與參數計算 72.3. 同頻、同相的控制方法和參數計算 8
2.7V to 5.5V input voltage Range? Efficiency up to 96%
? 24V Boost Converter with 12A switch
current Limit? 600KHz fixed Switching Frequency? Integrated soft-start? Thermal Shutdown? Under voltage Lockout? Support external LDO auxiliary power
supply? 8-Pin SOP-PP PackageAPPLICATIONSPortable Audio Amplifier Power SupplyPower BankQC 2.0/Type CWireless ChargerPOS Printer Power SupplySmall Motor Power Supply
ABSTRACTThe flyback power stage is a popular choice for single and multiple output dc-to-dc Converters at powerlevels of 150 Watts or less. Without the output inductor required in buck derived topologies, such as theforward or push-pull Converter, the component count and cost are reduced. This application note will reviewthe design procedure for the power stage and control electronics of a flyback Converter. In these isolatedConverters, the error signal from the secondary still needs to cross the isolation boundary to achieveregulation. By using the UC3965 Precision Reference with Low Offset Error Amplifier on the secondaryside to drive an optocoupler and the UCC3809 Economy Primary Side Controller on the primary side, asimple and low cost 50 Watt isolated power supply is realized.
This Section covers the design of power transformers used in buck-derived topologies: forward Converter, bridge, half-bridge, and full-wave centertap. Flyback transformers (actually coupled inductors) are covered in a later Section. For more specialized applications, the principles discussed herein will generally apply.
CHAPTER 1: THE OP AMP CHAPTER 2: OTHER LINEAR CIRCUITS CHAPTER 3: SENSORS CHAPTER 4: RF/IF CIRCUITS CHAPTER 5: FUNDAMENTALS OF SAMPLED DATA SYSTEMS CHAPTER 6: ConverterS CHAPTER 7: DATA Converter SUPPORT CIRCUITS CHAPTER 8: ANALOG FILTERS CHAPTER 9: POWER MANAGEMENT CHAPTER 10: PASSIVE COMPONENTS CHAPTER 11: OVERVOLTAGE EFFECTS ON ANALOG INTEGRATED CIRCUITS CHAPTER 12: PRINTED CIRCUIT BOARD (PCB) DESIGN ISSUES CHAPTER 13: DESIGN DEVELOPMENT TOOLS
The PW5300 is a current mode boost DC-DC Converter. Its PWM circuitry with built-in 0.2? powerMOSFET make this regulator highly power efficient. The internal compensation network alsominimizes as much as 6 external component counts. The non-inverting input of error amplifierconnects to a 0.6V precision reference voltage and internal soft-start function can reduce the inrushcurrent. The PW5300 is available in the SOT23-6L package and provides space-saving PCB for theapplication fields
