介紹了一種基于C8051F020單片機的多路壓力測量?jī)x。該測量?jī)x選用電阻應變式壓力傳感器采集壓力信號，并經放大電路處理后送入C8051F020單片機，再由C8051F020單片機內部的A/D轉換器將采集到的壓力信號進行模數轉化，然后分別對數據進行存儲和顯示。該測量?jī)x能測量6路壓力信號，并且各測量點都能單獨檢測和設置。由于采用了C8051F020單片機，簡化了硬件電路，增強了抗干擾能力，使得測量?jī)x具有測量精度高，沖擊小等特點。
Abstract:
A measurement apparatus for multi-channel pressure based on single chip microcomputer is introduced.It can measure 6 channels signal of the pressure，and the pressure measure points can be detection and located individually.The pressure signal sampling is obtained by resistor stress-type pressure sensors，the digital signals of 6 channels are collected through amplifying and adjustment circuit of pressure signals and internal integrated A/D Converter of MCU.Finally，and it realizes the function to store and display data separately.C8051F020 was used to made hardware circuit simple，and it also enhanced the anti-interference ability.It features high precision and little impact.
為了解決磁放大器性能測試過程中，需要對其供給不同數值恒定電流的問題，設計了一種基于DAC7512和單片機的數控恒流源系統。該系統采用AT89C51作為主控器件，將計算機發送的電流控制字命令轉換為D/A轉換器控制字，通過模擬SPI通信接口，寫D/A控制字到DAC7512，從而控制其輸出相應數字電壓值，經差動縮放電路、電壓/電路變換電路和功率驅動電路，最后輸出恒定電流。實驗結果表明，恒流源輸出電流調節范圍為-45~+45 mA、精度為±0.1 mA，分辨率達0.024 4 mA，具有應用靈活，外圍電路簡單，可靠性高的特點。該數控直流恒流源也可為相關產品的測試系統研發提供參考。
Abstract:
In order to solve the need to supply different values constant current for the magnetic amplifier in testing process， numerical control constant current source system was designed based on DAC7512 chip and microcontroller technology. The system used the AT89C51 as the main chip， which can convert the current control word from computer into to D/A control words. And the system wrote D/A control word into the DAC7512 chip to control the output voltage value by the SPI communication interface， which can output corresponding constant current figures by scaling circuit， the V/I Converter and power drive circuit. Experimental results show that the current source output current adjustment range is -45~+45mA， accuracy is ± 0.1mA， and resolution ratio is 0.024 4mA
針對51單片機系統中常用的A/D轉換器價格高、精度低的缺點，介紹TI公司的16 位的帶有I2C串行接口的A/D轉換器ADS1110的工作原理，給出ADS1110與AT89C51單片機系統的接口電路和軟件設計。實踐證明，ADS1110具有高性價比和實用性。
Abstract:
According to the disadvantages of high expense and low accuracy of the general A/D Converter used in MCS51 microchip system,the principle and working process of a high accuracy 16-bit A/D conversion ADS1110 which has I2C bus and belongs to TI Company are proposed here as well as the interface of ADS1110 to AT89C51 and software list.It is proved to be high performance index and practicability.
為深入了解基于UC3854A控制的PFC變換器中的動力學特性，研究系統參數變化對變換器中分岔現象的影響，在建立Boost PFC變換器雙閉環數學模型的基礎上，用Matlab軟件對變換器中慢時標分岔及混沌等不穩定現象進行了仿真。在對PFC變換器中慢時標分岔現象仿真的基礎上，分析了系統參數變化對分岔點的影響，并進行了仿真驗證。仿真結果清晰地顯示了輸入整流電壓的幅值變化對系統分岔點的影響。
Abstract:
In order to better understand the dynamics characteristic of power factor correction Converter based on UC3854A， and make the way that parameters change influences the bifurcation phenomena of the system clearly. The math model of the two closed loop circuits to the Boost PFC （Power Factor Correction） Converter controller was built. Then， with the help of Matlab， the simulation for nonlinear phenomena such as chaos and slow-scale bifurcation in the PFC Converter was made. Finally the factors that have influence to the phenomenon of bifurcation under slow-scale in PFC Converter were analyzed. The simulation results clearly show the parameters change influences the bifurcation point of the system.
詳細介紹了TLC1549系列模數轉換器的特點及工作原理，然后根據TLC1549的工作時序和A/D轉換原理針對實際問題編寫了詳細的匯編語言程序。
Abstract:
A basic principle and characteristic of TLC1549 analog-to-digital Converter are introduced? detailedly in this article.Through engineering-oriented illustration,a microcomputer programmer base on basic principle and time sequence of TLC1549 is writted.
介紹了基于單片機C8051F020的通用串口適配器的設計與實現方法，即由單片機控制的智能化一對多口收發信號轉換器。通過采用C51對單片機進行編程，控制與RS-232（標準RS-232電平）、RS232(TTL電平)、RS-422接口的數據通信；采用C++ Builder作為開發平臺，通過RS-232接口實現上位機對適配器各個通信端口的控制。
Abstract:
Design and realization of a universal serial port adapter based on the MCU C8051F020 are introduced.The adapter is an intelligent one-to-more receiving and transmitting signal Converter controlled by the MCU. By programming the MCU with the language C51,MCU control data communication between the MCU and RS-232(RS-232 level),RS-232(TTL level),RS-422 port; Using C++ Builder as the development plane, by one RS232 port, the upper PC can control each of the communication port of the adapter.
NEC 16位MCU參考手冊
The 78K0R/IC3 is a 16-bit single-chip microcontroller that uses a 78K0R CPU core and incorporates peripheral functions, such as ROM/RAM, a multi-function timer, a multi-function serial interface, an A/D Converter, a programmable gain amplifier (PGA), a comparator, a real-time counter, and a watchdog timer.
The XL6003 regulator is fixed frequency PWM Boost (step-up) DC/DC Converter, capable ofdriving 1050mA load current with excellent line and load regulation. The regulator is simple to use because it includes internal frequency compensation and a fixed-frequency oscillator so that it requires a minimum number of external components to work. The XL6003 could directly drive 5~10 3W LED units at VIN=12V.
The PAM2862 is a continuous mode inductivestep-down Converter, designed for driving singleor multiple series connected LEDs efficientlyfrom a voltage source higher than the LEDvoltage. The device operates from an inputupply between 6V and 30V and provides anexternally adjustable output current of up to 1A.Depending upon supply voltage and externalcomponents, this can provide up to 24 watts ofoutput power.
Luminary Micro provides an analog-to-digital Converter (ADC) module on some members of theStellaris microcontroller family. The hardware resolution of the ADC is 10 bits; however, due to noiseand other accuracy-diminishing factors, the true accuracy is less than 10 bits. This application noteprovides a software-based oversampling technique, resulting in an improved Effective Number OfBits (ENOB) in the conversion result. This document describes methods of oversampling an inputsignal, and the impact on precision and overall system performance.
